Microplex SOLID F44 User manual

User’s Manual
SOLID F44

Acknowledgements
PCL is a Trademark of Hewlett Packard Company.
A Publication of MICROPLEX Printware Corp
http://www.microplex-
usa.com Version: 5112
991 21751 August 2012
Great care has been taken to ensure that the information in this handbook is accurate and
complete. However, should any errors or omissions be discovered or should any user wish to
make suggestions for improving this handbook, please feel encouraged to send us the
relevant details.
The contents of this manual are subject to change without notice.
Copyright © by MICROPLEX Printware Corp.
All rights strictly reserved. Reproduction or issue to third parties in any form is not permitted
without written authorization from the publisher.

I
Safety Regulations for the Laser Printer SOLID F44 and the
intelligent Paper Stacker iPS F44
The laser printer SOLID F44 and the intelligent Paper Stacker iPS F44 fulfil
the safety regulations according to IEC EN 60950-1for information technology
equipments.
The mains cable must be connected only to a grounded protected wall-socket. The
printer´s mains voltage must agree with the local mains voltage.
The power plug must be easily accessible at any time so that it can be disconnected
immediately in case of danger or for maintenance purposes.
Before installing the printer, check the surrounding conditions in which the printer is
intended to be used (see next page, Operating Environment).
During thunderstorm you should never attempt to connect or disconnect any data
transfer cable.
The power supply should only be opened and checked by authorized personnel.
Maintenance beyond the descriptions of chapter 5 may only be attempted by
authorized personnel. Considerable dangers can arise through inappropriate repairs
for the user.
This symbol is standing for a hot surface.
Attention: danger of burning!
Note: It is to guarantee for the printer standing in a well ventilated room.

Safety Regulation
II
Electromagnetic Compatibility
We certify that the equipment at issue,
Type: Printer SOLID F44 and the intelligent Paper Stacker iPS F44 correspond
to the laws and regulations ruling electromagnetic compatibility of appliances
(2004/108/EC) and, therefore, fulfil the requirements for conformity marking with the
CE-sign.
To guarantee that the device stays within the limits according to the approval
regulations for conducted and radiated emission (EN 55022, Class B) and immunity
(EN 55024) in any case shielded interface cables are to be used only.
Note: This equipment has been tested and found to comply with the limits for a
CLASS A digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Changes and modifications not explicitly allowed by the equipment's manufacturer
could void the user's authority to operate the equipment
.
Operating Environment
Avoid installing the printer where it is exposed to moisture or heat (e.g. direct
sunlight).
The printer is designed to operate in a wide range of environmental conditions.
– Temperature: + 10°C to + 35°C (+50°F to + 95°F)
– Humidity: 30% up to 85%
For best performance, store and use fanfold paper at 19°to 23°C (68°to 73°F) and
a relative humidity of 33 to 47 percent.
Note: In case of higher values for temperature and humidity the print quality will
degrade!
Power Requirements
– 100 - 110 V (-10/+6%) AC, 12 A
– 110 - 120 V (-10/+6%) AC, 11A
– 220 - 240 V (-10/+6%) AC, 6 A
– 50 - 60 Hz
Note: To avoid an overload of the electric circuit support (particularly for 100 to 110
or 110 to 120V) connects the power supply plug of the printer into a
separate protected power wall socket.

Safety Regulation
III
Power Consumption
Operating power < 800 Watt average; (<1.300 W peak during Warming Up)
Operating current < 110 Watt
Power save ≤45 W
Notes: Slots and openings in the printer's housing are provided for ventilation.
Always ensure that these openings are not obstructed.
Also ensure that the cables of the printer do not interfere with the output
paper path.
The intelligent Paper Stacker iPS F44 can only be used in conjunction with the
printer SOLID F44.
Caution: Connector not located in limited Power Source! It is only for connecting the
Paper Stacker (iPS F44).
Use only Psi Interconnection Cable Type 5112-293-11563 to
Connect the Paper Stacker with the Printer SOLID F44
Caution, the chain of the motor to move the paper exit tray up
and own will start automatically or after pushing the key at the
front side of the table.
Caution, the paper exit tray moves up and down automatically
or after pushing the key at the front side of the table. Keep your
feet clear when the paper exit tray moves down. Ensure that the
cables at the rear of the printer do not interfere with the paper
path within the stacker.
The feet of the laser printer SOLID F44 should be positioned into the depressions of
the stacker's table.
Note: Open windows, airing, and also draught disturb the paper flow!
Move the Printer SOLID F44 (1) until to the
edge (3) of the iPS F44 (2). The right and left
side (4) must be flush with the iPS.

Safety Regulation
IV
Notes to Operators and Key Operators
1 The following safety rules should be observed
−The unit should be kept free from moisture, dirt, dust and exposure to eat and
direct sunlight at all times.
– Keep hands, hair and clothing away from rollers and other moving parts.
– Be sure that the proper voltage is used and that the machine is well rounded. The
use of electrical extension cords is strongly discouraged.
– For best performance, only our authorized supplies are recommended for use
with this unit. Failure to use our authorized supplies may cause damage to the
unit, in which case the warranty may be rendered void.
– Do not attempt to remove any Cover that is secured.
1.1 FCC Part 15 - Radio Frequency Devices (For U.S.A. Users)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
– This device may not cause harmful interference.
– This device must accept any interference received, including interference that
may cause undesired operation.
1.2 WARNING
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
hers own expense.
The design and production of this unit conforms to FCC regulations, and any
changes or modifications must be registered with the FCC and are subject to
FCC control. Any changes made by the purchaser or user without first contacting
the manufacturer will be subject to penalty under FCC regulations.
1.3 Interference-Causing Equipment Standard (ICES-003 ISSUE 4)
(For Canada Users)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.

Safety Regulation
V
1.4 CE Marking (Declaration of Conformity) (For European Users)
This product complies with the following EU directives:
2006/95/EC and 2004/108/EC directives.
This declaration is valid for the area of the European Union(EU) only.
This device must be used with shielded interface cable and shielded network
cable.
The use of non-shielded cable is likely to result in interference with radio
communications and is prohibited under rules.
1.5 Acoustic Noise
Machine Noise Regulation 3 GSGV, 18.01.1991: The sound pressure level
at the operator position according to EN27779 is equal to or less than 70dB
(A).
2 Safety Information
2.1 Laser Safety
This printer is a page printer which operates by means of a laser. There is no
possibility of danger from the laser, provided the printer is operated according
to the instructions provided in this manual.
Since radiation emitted by the laser is completely confined within protective
housing and external covers, the laser beam cannot escape from the machine
during any phase of user operation.
This printer is certified as a Class 1 laser product: This means that the printer
does not produce hazardous laser radiation.
2.2 Internal Laser Radiation
Maximum Average Radiation Power: 37 µW at laser Aperture of mirror unit
Wave Length: 770-800 nm
This product employs a Class IIIb Laser Diode that has an invisible laser
beam. The Laser Diode and Scanning Polygon Mirror are incorporated in the
print head unit.
The print head (in the interior of the printer in front of the toner cartridge)
consists of the print head unit and the mirror unit. The laser beam is emitted
from the print head unit, passes through the mirror unit, and then is radiated
through the laser aperture of the mirror unit to the interior of the printer.
2.3 CDRH Regulations
(For United States)
This printer is certified as a Class I laser product under the Regulation
Performance Standard according to the Food, Drug, and Cosmetic Act of
1990.
Compliance is mandatory for laser products marketed in the United States,
and is reported to the Center for Devices and Radiological Health (CDRH) of
the U.S. Food and Drug Administration (FDA) of the Department of Health
and Human Services (DHHS). This means that the product does not produce
hazardous laser radiation.
The label shown the indicated compliance with the CDRH regulations and
must be attached to laser products marketed in the United States.

Safety Regulation
VI
2.4 Laser treatment
WARNING
The print head unit is NOT A FIELD
SERVICE ITEM. Therefore, the print head
unit should not be opened under any
circumstances.
2.5 Label Indications
–For United States
CAUTION
Use of controls, adjustments or performance of procedures other than those
specified in this manual may result in hazardous radiation exposure.
This is a semiconductor laser. The maximum power of the laser diode is
15mW, and the wavelength is 770-800 nm
–All other users
Warning
Use of controls, adjustments of performance or procedures other than those
specified in this manual may result in hazardous radiation exposure.
This is a semiconductor laser. The maximum power of the laser diode is
15mW, and the wavelength is 770-800 nm.
Mirror Unit
Lase
r
Aperture
Print
Head
Unit

Safety Regulation
VII
–For Denmark
ADVARSEL
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion.
Undgå udsttelse for stråling. Klasse 1 laser produkt der opfylder IEC60825
sikkerheds kravene.
–For Finland, Sweden
VAROIUS!
Laitteen käyttäminen muulla kuin tässä köyttöohjeessa mainitulla tavalla
saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNNING
Om apparaten används på annat sätt än i denna bruksanvisning specificerats,
kan använderen utsattasr för osynling laserstrålnig, som överskrider gränsen
för laserklass 1.
VARO
Avattaessa ja suojalukitus ohitettaessa olet alttiina nakymattomalle
lasersateilylle. Aja katso sateeseen.
VARNING
Osynlig laserstråining när denna del är öppnad och spärren är urkopplad.
Betrakta ej stråien.
–For Norway
ADVARSEL
Dersum apparatet brukes på annen måte enn spesifisert i denne
bruksanvisning, kan brukeren utsettes for unsynlig laserstråling som
overskrider grensen for laser klasse 1.
Dette er en halvleder laser. Maksimal effeckt til laserdiode er 15mW, og
bolgelengde er 770-800 nm.

VIII
Table of Contents
Preface ............................................................................................................. XV
About this Manual................................................................................................. XV
Conventions used in this Guide ............................................................................ XVI
1. Installing the Printer and the intelligent Paper Stacker .............................. 1-1
1.1 Requirements to the location of the Printer............................................. 1-1
1.1.1 Environmental Conditions.................................................................... 1-1
1.2 A first look at the Device............................................................................ 1-4
1.3 Installing the intelligent Paper Stacker - iPS............................................ 1-5
1.3.1 Check delivery of Completeness ......................................................... 1-5
1.3.2 Unpack the iPS F44 ................................................................................. 1-5
1.3.3 Removing the transport locks .................................................................. 1-5
1.4 Unpacking and Installing the Printer ........................................................ 1-6
1.4.1 Delivery check for completeness.......................................................... 1-6
1.4.2 Unpacking the Printer SOLID F44 ........................................................ 1-7
1.4.3 Remove the Transport Locks............................................................... 1-8
1.5 Installing the Image Cartridge ................................................................... 1-9
1.6 Mounting the Tear off bar .......................................................................... 1-10
1.7 Align the Printer on the iPS ....................................................................... 1-10
1.8 Mount the Pendulum at the iPS F44 .......................................................... 1-11
1.9 Connect the Printer SOLID F44 with the iPS F44 ..................................... 1-12
1.10 Operating the iPS F44 ................................................................................ 1-12
1.10.1 Adjusting the Paper Exit Tray to the used paper length........................ 1-12
1.10.2 Open the Extensions of the Paper Tray................................................ 1-13
1.10.3 Remove Paper...................................................................................... 1-14
1.11 Connection to a Computer or to a Network ............................................. 1-14
1.12 Power ON/OFF Switch................................................................................ 1-15
1.13 Inserting Fanfold Paper ............................................................................. 1-16
1.13.1 Inserting paper for the first time or chaining to another
paper width ......................................................................................... 1-16