Microtronics myDatalogEx User manual

301022 | Rev.05
Cover
Valid from:
lFirmware version: 01v018
lApp. version: 01v000
lServer version: 49v011
lHardware version: 2.0
User manual
myDatalogEx

Chapter 1 Table of contents
Chapter 1 Table of contents
Cover 1
Chapter 1 Table of contents 3
Chapter 2 Declaration of conformity 7
Chapter 3 Ex certification 9
Chapter 4 Specifications 13
Chapter 5 General specifications 15
5.1 Translation 15
5.2 Copyright 15
5.3 General descriptive names 15
5.4 Ex protection 16
5.5 Safety instructions 16
5.5.1 Use of the hazard warnings 17
5.5.2 General safety instructions 17
5.5.3 Safety and preventative measures for handling GSM/GPRS modems 17
5.5.3.1 Safety and precautionary measures for the GSM/GPRS modem installation 18
5.5.3.2 Safety measures for installing the antenna 18
5.6 Overview 19
5.6.1 Block diagram 20
5.7 Intended use 20
5.8 General product information 21
5.9 Device labelling 21
5.10 Installation of spare and wear parts 22
5.11 Storage of the product 22
5.12 Warranty 22
5.13 Disclaimer 23
5.14 Obligation of the operator 23
5.15 Personnel requirements 24
Chapter 6 Functional principle 25
6.1 Functionality of the internal data memory 26
6.2 Procedure in case of connection aborts 27
6.3 Setup mode 27
Rev. 05 3

6.4 Automatic selection of the GSM network 31
Chapter 7 Storage, delivery and transport 33
7.1 Inspection of incoming deliveries 33
7.2 Scope of supply 33
7.3 Storage 33
7.4 Transport 33
7.5 Return 34
Chapter 8 Installation 35
8.1 Dimensions 35
8.2 Installing the myDatalogEx 36
8.2.1 Suspended installation 37
8.3 Electrical installation 38
8.3.1 Connecting the sensor 38
8.3.1.1 Connection examples 40
8.3.1.2 Use of the clamping tubes 41
8.3.2 Connecting the GSM antenna 41
8.3.2.1 Optimum antenna positioning for assembly in a shaft 42
8.3.2.1.1 Typical influences on the signal quality 42
8.3.2.1.2 Possibilities for improving the signal quality 42
8.3.2.1.3 Procedure for determining the optimum position of the antenna 42
8.3.3 Technical details about universal input 43
8.3.3.1 0/4...20mA mode 44
8.3.4 Technical details regarding the sensor supply 44
Chapter 9 Initial Start-Up 47
9.1 User information 47
9.2 Applicable documents 47
9.3 General principles 47
9.4 Placing the system into operation 47
9.4.1 Using the mobile connection (2G/3G) and the myDatanet server 47
9.5 Testing communication with the device 49
9.5.1 Testing communication between the myDatalogEx and the myDatanet server (mobile
connection) 49
Chapter 10 User interfaces 51
4Rev. 05

Chapter 1 Table of contents
10.1 User interface on the myDatalogEx 51
10.1.1 Operating elements 51
10.1.1.1 Reed switch 51
10.1.1.2 Display 52
10.2 User interface on the myDatanet server 54
10.2.1 Site configuration 54
10.2.1.1 Setup data 54
10.2.2 Device configuration 54
10.2.2.1 Comments 54
10.2.2.2 Measurement instrument 55
10.2.2.3 GPRS 56
Chapter 11 myDatanet server 57
11.1 Overview 57
11.1.1 Explanation of the symbols 57
11.2 "Customer" area 58
11.3 "Site" area at customer level 60
11.3.1 Reports 61
11.3.2 Map view 61
11.4 Recommended procedure 61
11.4.1 Creating the site 61
Chapter 12 API 65
12.1 Frontend API 65
12.2 rapidM2M PlaygroundrapidM2M Playground 65
12.2.1 Overview 66
Chapter 13 Maintenance 67
13.1 General maintenance 67
Chapter 14 Removal/disposal 69
Chapter 15 Troubleshooting and repair 71
15.1 General problems 71
15.2 Log entries and error codes 72
15.2.1 Modem error 74
15.3 Evaluating the device log 75
15.3.1 Evaluating the device log on the myDatanet server 75
Rev. 05 5

15.3.2 Evaluating the device log using DeviceConfig 76
Chapter 16 Spare parts and accessories 77
16.1 Assembly sets 77
16.2 Antennas 77
16.3 Cable 77
16.4 Other accessories 77
Chapter 17 Document history 79
Chapter 18 Glossary 81
Chapter 19 Contact information 83
6Rev. 05

Chapter 2 Declaration of conformity
Chapter 2 Declaration of conformity
Rev. 05 7

Chapter 3 Ex certification
Chapter 3 Ex certification
Rev. 05 9

10 Rev. 05