Midea NY1506-18SRA User manual

维修手册 Service Manual, 2017 v1.0
1/ 11
维修手册 Service Manual
适用机型 Applicable Models
机型编码 Model No.
机械式油汀 NY1506-18SRA
22057010001759
（本图片为参考示意图，具体外观和配置以实物为准）(The picture is only for reference, and
specific appearance and configuration are subject to the real product)
编制 Prepared by
钟少华
审核 Reviewed by
刘松
批准 Approved by
谭成波
重要安全通知

维修手册 Service Manual, 2017 v1.0
2/ 11
本维修手册仅用于具有适当电气、电子和机械经验背景的维修人员使用。
任何修理主要装置的测试均可能导致人身伤害和财产损失。
制造商或经销商不对本资料的内容和解释负责。
美的生活电器
技术手册
版权@2017
保留全部版权。未经美的生活电器外销书面批准，不得以任何形式全部或部分复制本手册。
Important Safety Notice
The Maintenance Manual is only for the use of maintenance personnel with certain experience and
background in electrical, electronic and mechanical field.
Any attempt to repair main devices may lead to personal injury and property loss.
Manufacturers or distributors are not responsible for the content of the Manual and interpretation
thereof.
Midea Environment Appliance
Technical Maintenance Manual
Copyright @2017
All rights reserved. Replication of all or part of the Manual in any forms shall not be allowed without
written approval by the Overseas Sales of Midea Environment Appliance.

维修手册 Service Manual, 2017 v1.0
3/ 11
1. 安全警示规范 Safety Warning Code
WARNING
1Read these instructions.
2Keep these instructions.
3Follow all instructions.
4Do not use this appliance near water. This appliance is intended to be used in
household and similar environments.
5Clean only with a damp cloth.
6Install in accordance with the manufacturer’s instructions.
7Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
8Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where the exit from the appliance.
9Do not attempt to modify or extend the power cord of this appliance.
10 Unplug this appliance during lightning storms or when it will not be used for long
periods of time.
11 Make sure that the available AC power matches the voltage requirements of this
appliance.
12 Do not handle the plug with wet hands. This could result in an electric shock.
13 Unplug the power cord by holding the plug, never by pulling the cord.
14 Do not turn the appliance on or off by plugging or unplugging the power cord.
15 Refer all servicing to qualified service personnel. Servicing is required when the
appliance has been damaged in any way, such as the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the appliance, the
appliance has been exposed to rain or moisture, does not operate normally, or has
been dropped.
16 To reduce the risk of fire or electric shock, do not expose this appliance to rain,
moisture, dripping, or splashing.
17 This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
18 Children should be supervised to ensure that they do not play with the appliance.
19 If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent, or similarly qualified person, in order to avoid a hazard.

维修手册 Service Manual, 2017 v1.0
4/ 11
2. 整机拆卸 Dismantling of appliance
2.1 盖板拆卸 coverplate disassemble
如图：使用一字螺丝刀从顶板散热孔处撬开盖
板，为防止划伤顶板，螺丝刀下面应垫棉布或
厚纸张。(As shown in the figure: Use a flat-blade
screwdriver to open the cover plate from the top
panel heat dissipation hole. To avoid scratching
the top panel, you can place a cotton cloth or
thick paper under the screwdriver.)
2.2 控制箱的拆卸 Control Box disassemble
逆时针拧下八颗螺钉，上下各四颗（Unscrew
eight screws counterclockwise, four up and four
down.）

维修手册 Service Manual, 2017 v1.0
5/ 11
2.3 拆卸零部件 parts disassemble
用十字螺丝刀到、尖嘴钳、电烙铁（拆卸插线
端子）拆下各个零部件（Use a Phillips
screwdriver , a needle nose pliers and a
soldering iron( remove the terminals) to remove
the parts）
3. 整机的安装 Function and operation
3.1 提手、控制面板的安装 Operation handle
将提手装饰件对应控制箱孔位套入并卡住。
同样的方法装好前面板。（Place the handle
decoration into the hole of the control box. The
same method installs the front panel.）

维修手册 Service Manual, 2017 v1.0
6/ 11
3.2 限温器的安装 thermostat assemble
将限温器装入壳体限温器支架离发热管较远
处，用两个螺钉固定（Place the temperature
limiter in the supporting far away from the heat
element. Then fix it with two screws.）
3.3 电路板的安装 PCB assemble
将控制板与电源板通过数据导线连接
3.4 支架与接线座的安装 support assemble
取一安装好电源线的连体支架对应控制箱底
部孔位插入安装，螺钉孔对位；
分别取 2颗盘头自攻螺钉 ST3.9*13 将连体支
架紧固在壳体上。（Take the connection
support with a power cable installed. Then
insert and install the hole in the bottom of the
control box, and align the screw holes; Finally,
take two pan head self-tapping screws
ST3.9*13 to fasten the connection support to

维修手册 Service Manual, 2017 v1.0
7/ 11
the control box.）
3.6 线束接线 wiring disassemble
按如图将线束插好，在接线座组件、限温器、
发热管、倾倒开关的插线端子上焊锡。（Insert
the terminals referring to the picture. Then
solder the terminals connecting to tip-over
switch, heating element, temperature limiter
and terminal block assembly. ）

维修手册 Service Manual, 2017 v1.0
8/ 11
3.7 顶板的安装 top plate assemble
将顶板放置于与壳体上方，取四颗螺钉固
定（Match up the top plate with cover well.
Then fix them with four screws.）
3.8 控制箱的安装 control box assemble
将前后控制箱与壳体配合，并用八颗螺钉固
定（Match up the front and back control boxes
with cover. Then fix them with eight screws.）
4. 常见及解决方法 Fault code and solutions
故障代
码Fault
code
故障内容
Fault
content
代码可
见Code
visible
显示 Display
维修方法步骤 Steps for maintenance methods
不通电 No
power
检查倾倒开关是否脱落 Check if the tip-over switch
fall off

维修手册 Service Manual, 2017 v1.0
9/ 11
5附录 Appendix:
5.1 整机接线图 Electrical Schematic Diagram
5.2 维修常用工具、设备和材料 refrigerator maintenance tooling and equipment and
material
工具 Tooling
No.
名称 Name
图片 Photo
主要用途 Main Usage
1
十字螺丝刀 Phillips
screwdriver
拆卸螺钉 screw assemble and
disassemble

维修手册 Service Manual, 2017 v1.0
10 / 11
2
平口螺丝刀 slotted
screwdriver
拆卸顶板 top plate disassemble
3
尖嘴钳 Nipper pliers
辅助工具 assistive tool
4
电烙铁 Soldering iron
拆卸插线端子 terminal
disassemble

维修手册 Service Manual, 2017 v1.0
11 / 11
美的生活电器
如需获得厂家详细技术咨询，请联系：
[e-mail]
生活电器事业部
外销
地址：中国广东省中山市东凤镇东阜路和穗工业园东区 28 号
Midea Environment Appliance
If you need to get detailed technical information from the manufacturer, please contact:
[e-mail]
EnvironmentAppliance Division
Overseas Sales
Address: Eastern 28th, Hesui industrial Park, Dongfu Road, Dongfeng Town, Zhongshan City,
Guangdong Province China