Midea NYERF User manual

OWNER’S MANUAL
OIL FILLED HEATER
MODEL:NYERF
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.
GD Midea Environment Appliances MFG.Co.,Ltd.
No.28, Dong Fu Road, Hesui East Industrial Area, Dong Feng Town,
Zhongshan, Guangdong 528425 P.R.China
145X210MM

1
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic precautions
should always be followed to reduce the risk of fire,
electrical shock and injury to persons , including the
following:
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the heater. Allow
heater to cool before moving and then use the built-in
handle for easy movement.
3. Extreme caution is necessary when heater is used by or
near children and whenever heater is left unattended.
4. Always unplug the heater when it is not in use.
5. Do not operate any heater with a damaged cord or plug,
or after the heater malfunctions, or has been dropped or
damaged in any manner. Return heater to the
manufacturer for examination, electrical or mechanical
adjustment, or repair.
6. Do not use heater outdoors. This product is intended for
normal household indoor use only.
7. This heater is not intended for use in bathrooms, laundry
areas or similar moist indoor locations. Never locate
heater where it may fall into a bathtub or other water
container.
8. Do not run power cord under carpeting. Do not cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be tripped
over.
9. To disconnect heater, set controls to OFF, then remove
plug from outlet.

2
10. Keep this heater clean. DO NOT allow foreign objects
to enter any ventilation or exhaust opening as this may
cause electric shock, or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces, like
a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or flammable
liquids are used or stored.
13. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
14. Warning: In order to avoid overheating, do not cover
the heater.
15. Do not use this heater in the immediate surroundings of
a bath, a shower or a swimming pool.
16. The heater must not be located immediately below a
socket-outlet.
17. If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
18. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

3
19.
20. This heater is filled with a precise quantity of special oil.
Repairs requiring opening of oil-container are only to be
made by the manufacturer or his service agent who
should be contacted if there is an oil leak. When
scrapping the heater, follow the regulations concerning
the disposal of oil.
21. Children of less than 3 years should be kept away
unless continuously supervised. Children aged from 3
years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in
its intended normal operating position and they have
been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the appliance
or perform user maintenance.
22. CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe
recycling.

4
WARNING: IN ORDER TO AVOID OVERHEATING,
DO NOT COVER THE HEATER.
PART FIGURE
Cord wrap
Caster assembly
Air Outlet
Power Indicator Light
Power Switch Knob
Thermostat Knob
Radiating unit
Air Outlet
Air Inlet
USE OF OIL FILLED RADIATOR
[Installation of the wheel carrier plate assembly]
1.Place the heater body inversely with the bottom upward.
2.Connect and tighten two wheel carrier plates to the body
with butterfly nuts as shown in the figure.
3.Place the heater upward after it is installed securely with
the wheels touching the ground.

5
OPERATING INSTRUCTION
[Inspection before start]
(1) The power cord shall not be damaged or fractured.
(2) This machine uses 220-240V AC power so please verify the rated current of the
power socket is in line with the requirements in the table above and is equipped
with a safety grounding device before use; otherwise, replace the socket.
[Start and power selection]
1. Start
Plug in the power, clockwise turn the thermostat knob to the "MAX" mark position,
then turn on the power switch, the heater starts to work.
2. Power selection
Under normal circumstances, please use the maximum power "HI" gear for rapid
heating. If the room temperature reaches a suitable temperature, please choose a
lower power "MED" or "LO" gear to reduce energy consumption so as to prevent
the room becoming overheated.
Note: To use the machine for the first time or to re-insert the socket, please pay
attention to check whether the plug and the socket are fitted well.
Inspection method: Insert the power plug into the socket and start for use; after
about half an hour, turn off and pull out the plug. Check whether the plug pins are
hot; replace the socket if so (more than about 50 °C) to avoid burning the plug or
even causing a fire caused by overheating of the socket due to poor contact.
[Temperature adjustment]
During use, if you feel it is necessary to lower the room temperature since it is too
high, you can use the following adjustment modes:
(1) Turn the power switch to gear "MED" or "LO".
(2) Counterclockwise turn the thermostat knob back by a certain angle, for which it
indicates that the set temperature is lower when the temperature indication is
closer to the "MIN" position.
[Fan function]
Press the fan switch to the "ON" position so that the fan heater starts working and
the room temperature will rise rapidly.
Note:
a. If the room temperature is below the set temperature, the indicator light will be
always illuminate.
b. The room shall be sealed; otherwise, the heating effect will be affected.
[Stop]
Turn the power switch to indication point "0FF", and then pull out the power plug.
[Movement of the heater]
To move the heater, turn it off first, and pull out the power plug; then push the body
to make the four casters below the body to roll.

6
MAIN TECHNOLOGY SPECIFICATIONS
Power supply: AC220-240V~ 50Hz
MODEL FAN LO MED HI
POWER REGULATION RANGE (W)
NY15ERF-7L
NY20ERF-9L
NY23ERF-11L
NY23ERF-13L
500
500
500
500
600
800
1000
1000
900
1200
1300
1300
1500
2000
2300
2300
TROUBLESHOOTING
If the product does not operate or does not operate properly, first check according
to the following list. If the reason the product does not operate or does not operate
properly is not included in the following list, the product may have failed. At this time,
it is recommended to send the product to the dealer or the Media Service Center for
treatment.
Problem Possible Cause Soluon
Aer the power is
engaged, the power
indicator light does not
illuminate and the
machine does not work.
The plug may not be
plugged well.
Check whether the plug is
properly inserted into the
receptacle.
The temperature control
knob is not turned in
place.
Check whether the
temperature control knob
is turned to the ON
posion.
The machine suddenly
stops during heang.
The temperature exceeds
the threshold of the
thermal cut-off.
Cool the machine before
use.