Midea NY2311-13AL User manual

OWNER’S MANUAL
OIL HEATER
MODEL: NY2311-13AL
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2016
GD Midea Environment Appliances MFG. Co.Ltd.
Attention: Pictures in the IM are for reference only.
No.28, Dong Fu Road, HeSui East Industrial Area, Dong Feng Town,
ZhongShan, GuangDong, China.

1
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic precautions
should always be followed to reduce the risk of fire,
electrical shock and injury to persons , including the
following:
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the heater. Allow
heater to cool before moving and then use the built-in
handle for easy movement.
3. Extreme caution is necessary when heater is used by or
near children and whenever heater is left unattended.
4. Always unplug the heater when it is not in use.
5. Do not operate any heater with a damaged cord or plug,
or after the heater malfunctions, or has been dropped or
damaged in any manner. Return heater to the
manufacturer for examination, electrical or mechanical
adjustment, or repair.
6. Do not use heater outdoors. This product is intended for
normal household indoor use only.
7. This heater is not intended for use in bathrooms, laundry
areas or similar moist indoor locations. Never locate
heater where it may fall into a bathtub or other water
container.
8. Do not run power cord under carpeting. Do not cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be tripped
over.
9. To disconnect heater, set controls to OFF, then remove
plug from outlet.

Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe
recycling.
2
10. Keep this heater clean. DO NOT allow foreign objects
to enter any ventilation or exhaust opening as this may
cause electric shock, or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces, like
a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or flammable
liquids are used or stored.
13. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
14. Warning: In order to avoid overheating, do not cover
the heater.
15. Do not use this heater in the immediate surroundings of
a bath, a shower or a swimming pool.
16. The heater must not be located immediately below a
socket-outlet.
17. If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
18.

3
19. This heater is filled with a precise quantity of special oil.
Repairs requiring opening of oil-container are only to be
made by the manufacturer or his service agent who
should be contacted if there is an oil leak. When
scrapping the heater, follow the regulations concerning
the disposal of oil.
20. CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
21. This heater is filled with a precise quantity of special oil.
Repairs requiring opening of oil-container are only to be
made by the manufacturer or his service agent who
should be contacted if there is an oil leak.
When scrapping the heater, follow the regulations
concerning the disposal of oil.

4
ASSEMBLY INSTRUCTIONS
PART FIGURE
WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER
THE HEATER.
Unpack your heater and find the wheel-holding plate and butterfly nuts
between the fins assemblies.
1. Make sure the heater is unplugged and in the "0" position.
2. Turn the heater upside down.
3. Attach the wheel-holding plates onto the heater as
Fig.1 shows. The U plate is fixed between the last
tow fins and the other one is fixed under metal
control box.
Fix the castors to the vertical axis of both the wheel
holding plates.
4. Insert the butterfly nuts and tighten them securely.
5. Turn the heater upright.
Your heater is now ready to use.
Radiating unit
Air inlet
Caster assembly
Power switch knob
Air inlet
Cord wrap
Carry handle
Thermostat knob
Air inlet

OPERATING INSTRUCTIONS
WARNING: Risk of fire. Do not operate heater without wheel
assemblies attached. Operate heater in upright position only
(wheels on bottom, controls on top). Any other position could create
a hazardous situation. Ensure that the surface beneath the heater is
clean and free of any obstructions. It is not recommended that this
heater be placed on high-pile carpeting or any other surface that
impedes the flow of air underneath the heater.
1. Plug in the heater.
2. Turn the thermostat knob to the maximum position.
3. Switch the heater on by setting the power switch to the desired heat
setting.
1 ― Low heat 2― Medium heat 3 ― High heat
The power indicator light will illuminate.
4. When the room has reached the required temperature, turn the
thermostat knob slowly anticlockwise until the power indicator light
goes out (or until a click is heard).
5. Turn the thermostat knob to this position to set the desired
temperature.
The power indicator light will turn on and off, indicating the thermostat
is keeping room temperature at the selected setting.
6. To turn the heater off, set the power switch to the “0” position and
remove plug from the mains socket.
5
SAFETY FEATURES
Safety Tip-over switch:
The heater features a tip-over switch. If the heater tips over, it will
automatically switch off. Once placed back into the upright position, the
heater will automatically switch on again.
Overheat protection:
The heater is equipped with a safety device. The safety device will trip
and turn the heater off in the event of overheating.

6
CLEANING AND MAINTENANCE INSTRUCTIONS
1. The electric heater should be cleaned regularly to wipe out the dust
on the surface of flanges. As this may influence the radiating
efficiency.
2. Disconnect electricity supply and allow radiator to cool, wipe out dust
with a soft damp cloth. Do not use detergent or abrasives.
3. Do not scrap the surfaces of flanges with sharp hard tools, to avoid
surfaces getting rusty, because of damage of the paint coat.
TECHNICAL SPECIFICATIONS
Model No. NY2311-13AL
Voltage 230-240V AC
Frequency 50Hz
Power Low 880-960W / Middle 1320-1440W / High 2200-2400W