miseno MNO163620F6040 User manual

General Recommendations:
Tools and Materials needed:
1
Please read installation and maintenance instructions thoroughly.
Inspect your sink for any noticeable damage before installation.
Check all local applicable plumbing and building codes.
These instructions are based on application to composite material or solid surface countertop installation
only; countertop application to stone, marble, granite or butcher-block should be referred to an
experienced countertop fabricator for custom installation.
Because Miseno Farmhouse sinks are individually handmade, we suggest using experienced and
professional installers only. For custom cutting of countertop and installation of the actual sink, on-site
installation is also recommended. Acceptable variances are approximately 1/8 of an inch. Alignment to
the cut-out and precise application and trimming of any adhesive sealant are critical to a superior fit and
finished look. Please take extra care in this regard.
Miseno Farmhouse sinks require custom cabinetry. Consult a contractor or cabinet maker.
Miseno does not accept any liability for damage to countertop, sink fixture, faucets or personal injury
during installation. Warranty is void if installation instructions are not followed.
Be sure to use proper tools and always wear personal safety devices for your protection.
Tape Measure
Hacksaw / Jigsaw
Rags
Pencil (NOT ink)
Framing Square
Ear Protection
Shims
Denatured Alcohol
Eye Protection
Silicone Adhesive Sealant
Wood Braces
Handmade Farmhouse Sinks
Installation Instructions
Contact Miseno at [phone] or email [email protected] with any questions. Copyright ©2019, Miseno. All rights reserved
MNO163620F6040

Installation Options:
Miseno farmhouse sinks offer several installation options depending on your design.
Caution: All installation types need to allow room for your faucet. Be sure there is adequate clearance
behind the sink for any faucet(s) and your backsplash, as well as clearance for a full range of motion
for faucet spouts and handles.
Typical undermount installation with 1/4" reveal recommended.
Typical flush mount and protruding installation
Protruding installation exposes the sides of the sink up to 1" above the countertop.
Undermount Installation Flush mount Installation Protruding Installation
!
Handmade Farmhouse Sinks
Installation Instructions
Contact Miseno at [phone] or email [email protected] with any questions. Copyright ©2019, Miseno. All rights reserved

1. Prepare the Sink Base Cabinet:
Due to the variety of potential installation options, this guide is a general overview and not a plan.
Farmhouse sinks require custom cabinets with a front cutout to accommodate a 10" deep sink. Build a
plywood platform on a support frame inside of the cabinet. Platform must be able to support the weight of
the sink and any attachments such as garbage disposals. When the sink is placed onto a platform, make
sure the top of the sink is evenly flush against the bottom of the countertop. Allow clearance for water
supply line and drains or garbage disposal, as necessary.
Set the sink on top of the cabinet or into the cabinet front cutout. Apply sealant as necessary as a gasket
between the sink and cabinet, and to hold the sink in place.
2. Make a Template and Cutout
3. Set the Sink
For undermount installations, carefully clean bottom of countertop and top flange of sink with denatured
alcohol. Apply bead of silicone adhesive (not supplied) around the top edge of the sink. Place countertop
onto the sink. Remove excess sealant from the lip or any surfaces with a cleaner recommended by the
sealant manufacturer. For flushmount or protruding installations apply a bead of silicone in the seam
between the countertop and sink. Wipe off any excess and allow to cure for 24 hours before use.
4. Install the Countertop
The installation option you choose will
determine how you cut your countertop.
Miseno recommends a 1/4" reveal on 3 sides
when installed undermount style. For a flush
mount or protruding installation, cut countertop along
the outside line of the sink profile. The front of a Miseno
Farmhouse sink is designed to be installed with 3/4” of the face
extended out beyond the front edge of the countertop. Cut the
countertop accordingly. No template is provided due to the custom
nature of each application and installation. The actual sink is used
as the template guide. After centering the sink and allowing for
any faucets and backsplash, use a pencil to outline the sink as
your guide for the cutout. Check your reveal
on all sides before cutting.
Handmade Farmhouse Sinks
Installation Instructions
Contact Miseno at [phone] or email [email protected] with any questions. Copyright ©2019, Miseno. All rights reserved