Mocka Activity Table User manual

Activity Table
1
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Hardware Supplied
B
AC
DE
x52
x52 x48
x16
x4
bolt
locking nut dowel
screw
wheels
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
Phillips screwdriver required
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
Thank you for your purchase.
Please follow the instructions below for correct assembly.

1x 2
Activity Table
2
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Begin assembly by screwing in 24x bolts (A) into all corresponding
holes as shown in both panels [4] using a Phillips screwdriver. Take
care not to overtighten bolts.
A
x24
A
A
A
A
A
A
A
A
AAA
A
2x 2
Screw in 2x bolts (A) and insert 2x dowels (C) into holes in each of the
panels [1] and [3]. Slot together with the rest of panel [2] as shown.
Place locking 4x nuts (B) into holes in the panel and tighten with
screwdriver. Repeat step.
A
x4
B
B
B
B
C
C
A
A
2
3
1
C
C
A
A
B
x4
4

3
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Slot both the components assembled in the previous step together with
one panel [4]. Place 6x locking nuts (B) and 8x dowels (C) into holes in
the panels as shown an tighten with screwdriver.
Activity Table
3
B
B
4
B
B
B
x6
C
C
CC
CC
CC
4
Screw in 2x bolts (A) and insert 2x dowels (C) into holes in each of
panels [6]. Slot together with the table panel [5] as shown. Place
locking 4x nuts (B) into holes in the panel [5] and tighten with
screwdriver.
B
B
B
B
A
A
C
C
A
C
5
6
6
A
C
B
x4
A
x4

4
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Activity Table
5
Slot the tray together onto the rest of the table structure as shown.
Place 6x locking nuts (B) and 4x dowels (C) into holes. Insert 8x dowels
(C) into the top and slot on side panel [4]. Fasten with 12x locking nuts
(B) and tighten with a screwdriver.
5
C
C
B
B
B
BB
x18
C
C
CC
4
C
B
B
B
B
B
B
To assemble the drawers first screw 2x bolts (A) and insert 2x dowels
(C) into each of the panels [7]. Fit together with panel [8] as shown.
Secure using 4x locking nuts (B) and fasten with a screwdriver.
6Drawer
8
7
7
A
C
A
C
A
C
A
C
B
B
B
B
B
x4
A
x4

Attach the sides by screwing 6x bolts (A) and inserting 6x dowels (C)
into each of the panels [9]. Slot both panels [9] down into holes in
panels [7] and [8]. Secure using 12x locking nuts (B) and fasten with a
screwdriver.
7Drawer
Activity Table
5
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
8
9
Cx2 A
A
Cx2 A
A
A
A
A
A
9
B
B
B
B
7
B
x12
A
x12
Cx2
A
AC
C
B
C
C
Cx2
8Drawer
Attach 4x wheels (E) in position to the base of the drawer unit using 4x
screws (D) with each wheel piece. Tighten all screws securely with a
screwdriver.
Dx4
E
Dx4
E
x4
D
Dx4
E
Dx4
E

9Drawer
Activity Table
6
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
The drawer assembly is all done! Flip the drawer up onto its wheels as
shown, and follow on to final steps to complete assembly of the Activity
Table.
10
Slide the completed drawer under the activity table. Finally check all
screws and locking nuts are securely fastened with a screwdriver
before use.

11
Activity Table
7
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Place the lid [10] over the activity table when it’s not in use. You’re
done, enjoy!
10