Mocka Kennedy Entertainment Unit User manual

Phillips & Flathead screwdrivers required
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing
device provided should fit most wall types, but please note that different wall materials may require
different fixing devices from those supplied.
Wall Strap
x2
washer
Z
Y
wall
anchor
x1
X
safety
strap x1
WV
screw
x1
wall
screw
x1
A B C D E F G HJKL
M N
I
O
Hardware Supplied
PQR
dowel
x20
screw
x41
bolt
x24
locking
nut x24
bolt
x4
screw
x5
slide
rail x1
wedge
x12
slide
rail x1
slide
rail x1
slide
rail x1
allen
key x1
bracket
x3
cover
x3
stopper
x3
hinge
x4
small
bolt x16
bracket
x4
ST
screw screw
x10 x12
U
adjuster
x1
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
A1
washer
x16
Kennedy Entertainment Unit
1
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

12
19
Attach 2x brackets (M) to panel [1] and secure with 4x screws (E). Place 2x
covers (N) over them as shown. Attach panel [8] to panel [1] using 2x screws
(S). Attach 1x bracket (M) to panel [2] and secure with 2x screws (E). Place
1x cover (N) over the bracket. Attach the support leg [19] to the underside of
panel [2] with 1x screw (F). Tighten with a screwdriver.
Attach 1x slide rail (H) to panel [5] and secure with 2x screws (E).
Attach 1x slide rail (J) to panel [6] and secure with 2x screws (E).
Tighten with a screwdriver.
8
2
1
EE
E
SE
EE
M
M
M
N
M
E
6
5
H
E
E
J
EE
M
S
E
F
F
EE
H x1 & J x1
Kennedy Entertainment Unit
2
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions

12
19
Attach 2x brackets (M) to panel [1] and secure with 4x screws (E). Place 2x
covers (N) over them as shown. Attach panel [8] to panel [1] using 2x screws
(S). Attach 1x bracket (M) to panel [2] and secure with 2x screws (E). Place
1x cover (N) over the bracket. Attach the support leg [19] to the underside of
panel [2] with 1x screw (F). Tighten with a screwdriver.
Attach 1x slide rail (H) to panel [5] and secure with 2x screws (E).
Attach 1x slide rail (J) to panel [6] and secure with 2x screws (E).
Tighten with a screwdriver.
8
2
1
EE
E
SE
EE
M
M
M
N
M
E
6
5
H
E
E
J
EE
M
S
E
F
F
EE
H x1 & J x1
34
Attach panels [5] and [6] to panel [7] using 4x dowels (A) and 4x bolts
(B). Secure with 4x locking nuts (C) and tighten with a screwdriver.
Attach panels [4], [6], [5] and [3] to panel [1] using 8x dowels (A), 8x bolts
(B) and secure with 8x locking nuts (C). Tighten with a screwdriver.
C
6
7
5
4
3
C
C
CA
B
A
B
A
B1
C
C
C
C
A
BA
B
A
BAB
A
BAB
A
BAB
C
6
5
Kennedy Entertainment Unit
3
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions

56
Slide panels [9] and [10] along the grooves between panels [3], [4], [5]
and [6] to form the back of the unit.
Attach panel [2] to the rest of the unit using 8x dowels (A), 4x bolts (B)
and 4x locking nuts (C). Tighten with a screwdriver.
10
9
9
2
A
B
C
C
CC
C
C
C
AB
AA
AA
A
B
AB
4
3
5
6
Kennedy Entertainment Unit
Assembly Instructions
4
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
56
Slide panels [9] and [10] along the grooves between panels [3], [4], [5]
and [6] to form the back of the unit.
Attach panel [2] to the rest of the unit using 8x dowels (A), 4x bolts (B)
and 4x locking nuts (C). Tighten with a screwdriver.
10
9
9
2
A
B
C
C
CC
C
C
C
AB
AA
AA
A
B
AB
4
3
5
6
78
Attach a leg bracket (R) to each leg [18] using 2x screws (S) and 1x bolt
(G). Tighten with a screwdriver and allen key (L). Attach each leg [18] to
panel [2] using 4x small bolts (Q) and 4x washers (A1) as shown. Tighten
with the allen key (L). Insert the adjuster (U) into the middle support.
Attach 12x wedges (D) to the back of the unit as shown and secure with
12x screws (T). Tighten with a screwdriver.
D
T
2
18
R
Q
Q
Q
U
L
G
LS
S
X4
19
A1
A1
A1
A1
Q
18
Front
Back
Front
Kennedy Entertainment Unit
Assembly Instructions
5
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

910
Attach 1x stopper (O) to door panel [11] using 1x screw (E). Attach 2x
hinges (P) to panel [11] and secure with 4x screws (E). Attach 1x
stopper (O) to door panel [12] using 1x screw (E). Attach 2x hinges (P)
to panel [12] and secure with 4x screws (E).
Secure door panels [11] and [12] to the main unit by attaching the other
end of the hinges (P) with 16x screws (E) as shown.
12
11
E
O
E
O
P
P
EE
E
E
NOTE: If the doors are uneven or
there is a gap in the middle, loosen
or tighten the screw on the door
hinge until they are sitting flush.
12
11
x4
P
E
Kennedy Entertainment Unit
Assembly Instructions
6
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

910
Attach 1x stopper (O) to door panel [11] using 1x screw (E). Attach 2x
hinges (P) to panel [11] and secure with 4x screws (E). Attach 1x
stopper (O) to door panel [12] using 1x screw (E). Attach 2x hinges (P)
to panel [12] and secure with 4x screws (E).
Secure door panels [11] and [12] to the main unit by attaching the other
end of the hinges (P) with 16x screws (E) as shown.
12
11
E
O
E
O
P
P
EE
E
E
NOTE: If the doors are uneven or
there is a gap in the middle, loosen
or tighten the screw on the door
hinge until they are sitting flush.
12
11
x4
P
E
11
12
Attach 1x stopper (O) to panel [13] using 1x screw (E). Attach side panels
[14] and [15] to panel [13] using 4x bolts (B) and secure with 4x locking
nuts (C). Tighten with a screwdriver. Slide panel [17] along the grooves
between side panels [14] and [15] to form the base of the drawer.
Screw on the back panel [16] using 4x screws (F). Attach 1x slide rail (I)
to panel [14] and 1x slide rail (K) to panel [15] using 4x screws (E).
Tighten with a screwdriver.
Drawer x1
17
14
15
13
14
15
B
B
B
C
C
14
15
FF
F
F
16
14
15
13
I
K
E
E
E
13
E
O
Kennedy Entertainment Unit
Assembly Instructions
7
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

13 14
Insert the drawer into the unit at an upwards 45˚angle. See the diagram
above for the correct positioning of the slide rails. If the door is not
catching or sitting flush, twist the end of the cover (N) until it catches on
the stopper (O).
Ensure the drawer slides easily along the rails.
45°
N
Kennedy Entertainment Unit
Assembly Instructions
8
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

13 14
Insert the drawer into the unit at an upwards 45˚angle. See the diagram
above for the correct positioning of the slide rails. If the door is not
catching or sitting flush, twist the end of the cover (N) until it catches on
the stopper (O).
Ensure the drawer slides easily along the rails.
45°
N
15 16
Attach 1x safety strap (V) to the top of the back side of the unit as shown
using 1x washer (Z) and 1x screw (W). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (V). Fasten to wall
using 1x wall plug (X), 1x washer (Z) and 1x wall screw (Y). Ensure unit
is balanced and steady before use. You’re done, enjoy!
Wall Mount
wall
plug
wall
screw
strap
washer
X
Y
Z
V
Z
V
W
V
W
Z
Kennedy Entertainment Unit
Assembly Instructions
9
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558