Mocka Locka Double User manual

A B C
D E F
Phillips screwdriver required
Hardware Supplied
clip
x16
ring
x2
rod
x4
handle
x2
bolt
x4
wall mount
x1
WARNING: Any furniture that is not anchored to a
wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on
the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is
anchored to a wall. We supply a free safety wall
anchor with all furniture sold and we recommend
these are used to prevent your product tipping. The
fixing device provided should fit most wall types, but
please note that different wall materials may require
different fixing devices from those supplied.
Locka Double
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

12
Slide the legs [3] and [4] into the bottom of the side panels [1] and [2]
until they click into place.
CLICK!
CLICK!
CLICK!
CLICK!
Insert each end of the shelf bracket [10] into the gaps on the sides of
the unit, as shown.
4
3
2
12
1
10
Locka Double
2
mocka.co.nz | mocka.com.au
Assembly Instructions

12
Slide the legs [3] and [4] into the bottom of the side panels [1] and [2]
until they click into place.
CLICK!
CLICK!
CLICK!
CLICK!
Insert each end of the shelf bracket [10] into the gaps on the sides of
the unit, as shown.
4
3
2
12
1
10
34
Attach the top panel [6] to the rest of the unit.
Insert the back panel [5] as shown.
5
2
12
1
6
Locka Double
3
mocka.co.nz | mocka.com.au
Assembly Instructions

56
Secure the top panel by clicking into place as shown. Insert the bottom and middle shelves [7] by clicking into place as shown.
NB. If you ever need to take the shelves out to readjust their height,
please use a flat head screwdriver to loosen the clips from underneath.
2
1
7
7
Locka Double
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
56
Secure the top panel by clicking into place as shown. Insert the bottom and middle shelves [7] by clicking into place as shown.
NB. If you ever need to take the shelves out to readjust their height,
please use a flat head screwdriver to loosen the clips from underneath.
2
1
7
7
78
Insert 16x clips (A) into the back and front clip brackets at your desired
shelf height as shown. Place the four shelf panels [8] into the unit over
the clips to form the shelves.
Attach handle (D) to door panel [9] with 2x bolts (E) and tighten with a
screwdriver.
x16
A
A
E
ED
8
8
8
8
9
Locka Double
Assembly Instructions
5
mocka.co.nz | mocka.com.au

910
Attach the bottom door by inserting 1x ring (B) and 1x rod (C) through
the door panel [9] as shown. Twist the rod into place and secure by
bending the clasp down.
To attach the top of the door, insert 1x rod (C) through the door panel as
shown. Twist the rod into place and secure by bending the clasp up onto
it. Repeat steps 9 and 10 to attach the top door.
B
C
C
C
C
9
Locka Double
Assembly Instructions
6
mocka.co.nz | mocka.com.au

910
Attach the bottom door by inserting 1x ring (B) and 1x rod (C) through
the door panel [9] as shown. Twist the rod into place and secure by
bending the clasp down.
To attach the top of the door, insert 1x rod (C) through the door panel as
shown. Twist the rod into place and secure by bending the clasp up onto
it. Repeat steps 9 and 10 to attach the top door.
B
C
C
C
C
9
11
12
Lift the completed unit into place, do not drag. Mark its height on the
wall with a pencil. Attach one end of the wall mount strap to the back of
the unit with a 1x screw (F). Screw the other end into the wall at the
marked height with a wall screw (not supplied).
You’re done, enjoy!
F
Wall Mount
Locka Double
Assembly Instructions
7
mocka.co.nz | mocka.com.au