Mocka Zara User manual

1
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Zara
Oce Desk
Thank you for your purchase.
Please follow the instructions below for correct assembly
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall
anchor with all furniture sold and we recommend these are used to prevent your product tipping.
The fixing device provided should fit most wall types, but please note that dierent wall materials
may require dierent fixing devices from those supplied.
Phillips & Flathead screwdrivers and hammer required.
*We recommend using a Flathead screwdriver to tighten
all locking nuts 100% before first use.
.
Wall Strap
x2
Z
washer
Y
wall
x1
X
anchor
safety
WV
strap x1 x1
screw wall
x1
screw
x16
bolt
x4
A B C D EFGHJ
KLMN
I
O P Q R
Hardware Supplied
x16
dowelscrew
x26
slide
rail x2
slide
rail x2
slide
rail x2
slide
rail x2
locking
nut x16
x8
screw
x4
wedge
screwspring
washer
x8
bracket
x2
washer
x8
cover
x2
seal
x2
felt
pad
x4
bolt
x8
S
x8
screw
T
Allen
key x1

1
Zara
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
2
Oce Desk
2
Insert 8x bolts (C) into panel [1] and tighten with a screwdriver. Attach 1x slide rail (F) and 1x slide rail (G) to panels [3] and [5]
as shown and secure with 6x screws (E). Tighten with a screwdriver.
G
F
G
CR
E
F
CL
E
1
5
3
C
C
C
C
C
C
C
C
E
E
E
E
E
E

Zara
Oce Desk
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Attach 1x slide rail (F) and 1x slide rail (G) to panels [6] and [4]
as shown and secure with 6x screws (E). Tighten with a screwdriver.
3 4
Attach panels [3], [4], [5] and [6] to panel [1] with 8x dowels (A) and secure
with 8x locking nuts (D). Tighten with a screwdriver.
G
F
G
CR
E
F
CL
E
4
6
E
E
E
E
E
E
4
6
D
A
A
DA
A
DA
A
A
A
D
D
D
D
D
1
3
5

mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Zara
Oce Desk
5 6
Slide panel [7] along the grooves between the side panel [3] and [4]
to form the back of the unit.
Attach 2x bracket (M) to panel [2] and secure with 4x screws (E).
Tighten with a screwdriver. Place 2x cover (N) over the bracket (M)
as shown.
EE
N
M
4
M
The round head
is aligned with the
direction of the arrow.
2
EE
M
EE
M
3
7

Zara
Oce Desk
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Attach panel [2] to the unit with 8x dowels (A) and secure with 8x screws (B).
Tighten with a screwdriver.
Attach legs [8] to panel [2] and secure with 8x bolt (R), 8x washer (P),
8x spring washer (Q). Tighten with an Allen key (T). Attach 4x felt pads
(L) to legs [8] as shown.
7 8
A
AA
A
A
B
B
B
B
B
B
B
B
2
4
6
5
3
8
8
2
8
8
P
Q
R
8
L
L
L
L
T
P
Q
R

Zara
Oce Desk
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Insert 4x bolts (C) into panel [9]. Attach 1x seal (O) to panel [8] and secure
with 1x screw (E). Tighten with a screwdriver.
Insert 4x bolts (C) into panel [9]. Attach 1x seal (O) to panel [8] and secure
with 1x screw (E). Tighten with a screwdriver.
109Drawers x2
C
C
C
C
E
O
9
D
D
D
D
11
10
9

11
Zara
Oce Desk
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Attach slide rail (I) and slide rail (H) to the underside of the side panels as shown.
Secure with 4x screws (E) and tighten with a screwdriver.
Insert the assembled drawers into the corresponding compartments
as shown. Ensure the drawers slide easily along the rails. If the door
is not catching or sitting flush, twist the end of the cover (N) until it
catches on the seal (O).
12Drawers x2Drawers x2
9
10
12
11
11
9
10
13
S
S
S
S

13
Zara
Oce Desk
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
Attach 4x wedges (J) into the corners of the back of the unit and secure
with 4x screws (K). Tighten with a screwdriver. Attach 1x safety straps (V)
to the top of the back side of the unit as shown using 1x washers (Z) and
1x screws (W). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (V). Fasten to the
wall using 1x washers (Z), 1x wall anchor (X) and 1x screws (Y). Ensure unit
is balanced and steady before use. You’re done, enjoy!
14
ASSEMBLY I N S TRUCTION S
K
J
V
Z
W
V
Z
W
X
Y
Z
anchor
wall
screw
strap
washer
J
K
1
7