Modena RX Series Owner's manual

1
User
Manual Book
Slim Hood
Series
RX

2
TABLE OF CONTENTS
FEATURES 3
INSTALLATION 4
Installation the exhaust hood on the wall 4
Preparations before installing the exhaust hood 4
Installation of exhaust hood 5
Installation on the bottom part of the kitchen set 6
Operating procedure 7
HOW TO USE 9
Touch button 9
MAINTENANCE 10
Cleaning the cabinet 10
Cleaning the filter 10
TROUBLESHOOTING 12
SPECIFICATION 13
This guide book explains everything you need to know about your new
product. Please contact our Customer Care should you need further
assistance through www.modena.com.

3
1. Carbon Filter
2. Direction airflow
3. Control panel
4. Lamp
5. Aluminum filter
6. Filter holder
FEATURES

4
Exhaust hood is an equipment which sucks smoke and cooking
fragrance. With a vent hood, your kitchen will be free from oil particles
that may produce bad odor.
1. Check the strength of wall on which the
exhaust hood is to be installed. Make sure
the wall can sustain the weight / load of
the vent hood.
2. The exhaust hood should be installed
precisely over the stove at a vertical
distance of 65 - 75 cm from the stove
surface.
Installing the exhaust hood on the wall
Exhaust hood must be installed perpendicularly
to prevent the oil from flowing to one side and
dripping out of the vent hood.
Preparations before installing the exhaust hood
1. Remove the exhaust hood from its packaging and put it on an
even place (e.g. Tables).
2. Open the aluminum filter and then pull it. Remove the spigot/
flange (pipe connector) and the hole cover from the plastic bag.
3. Turn the air directing knob to the following position:
•Exterior symbol for ducting/exhaust system
•Interior symbol for re-circulating system
4. Reassembling the aluminum filter
INSTALLATION

5
5. The exhaust hood has two holes on it: Hole D and Hole E (look at
the picture). To install the spigot/flange and hole cover, follow
these instructions: follow these instructions:
•For ducting / exhaust system: Install
the spigot / flange G on one of the air
holes, either D or E. Holes which do
not have spigot / flange shall be
covered with Hole Cover H.
•For re-circulating system: Both air
holes D and E shall be covered with
the available plastic Hole Cover.
Installation of exhaust hood
Exhaust hood can be installed on the concrete (brick) wall or the bottom
part of the kitchen set.
Installing on concrete (brick) wall
1. Draw a centerline on the wall where the exhaust
hood is to be installed (1).
2. Post a template for drilling on the wall (2). If no
template is available, attach the exhaust hood
on the wall and mark the spot on the wall where
a hole is to be made.
3. Create holes on the four marks with a 6 mm diameter drill bit or
fisher size (3), and then insert the fisher to the four holes (4).
ATTENTION!
Before drilling, make sure that there's no cable installation, water
pipe and installation inside the wall.

6
4. Install the screw on noth upper holes
and set aside 1 cm between the head
of the screw and the wall surface (5).
5. Install the exhaust hood on the
screwes wall by suspending the vent
hood on the screq (6).
6. When the exhuast hood is positioned
correctly on the wall, tighten both
screws on the upper part (7)
7. To reinforce the exhaust hood handle on the wall, install the
screws on both holes on the bottom part (8) and tighten them
(9).
8. Reassembling the aluminum filter.
9. Connecet the exhaust system with the spigot/falnge if the
exhaust hood is to be operated as a ducting/ exhaust system.
Installation on the bottom part of the kitchen set
1. Put the exhaust hood on the bottom
part of the kitchen set in accordance
with the planned position.
2. Mark the bottom part of the kitchen
set for flexible pipe hole and then
create a hole if the exhaust hood is to
be operated with ducting/exhaust
system.
3. Install the exhaust hood with 4 screws on the prepared position.
4. To reinforce the exhaust hood handle on the kitchen set, install
the screws on other holes on the upper part and tighten them.
5. Connect the exhaust system with the spigot/flange if the
exhaust hood is to be operated as a ducting/exhaust system.

7
Operating procedure
MODENA Exhaust Hood has 2 (two) work methods as follows:
DUCTING / EXHAUST System:
•In this mode, the exhaust hood
operates by sucking the smoke/
cooking odor and then discharging it
out of the vent.
•A heat/fire-resistant ducting system is
required to discharge smoke/odor out
of the vent.
•To connect the exhaust hood with the discharge duct, use
"spigot/flange" is designed with a diameter of 100 or 125 mm.
Several things which require attention in installing the ducting system
exhaust hood:
1. Carbon filter must be removed because
the cooking odor will be sucked and
immediately discharged out of the room.
2. The suction force will be diminished if
the exhaust system is too long and there
are too many elbows.
3. Do not connect the exhaust system with a chimney or an air duct
or hot steam duct.
4. If the exhaust hood is to be installed in a multi-storied building or
an apartment, consult with the person in charge of the building /
apartment prior to installing the exhaust system.
5. Exhaust hood with ducting system should be used in an open-
air room with good air circulation.
RECIRCULATING system:
In this version, the exhaust hood sucks the smoke/cooking odor and
filters it through an aluminum filter and carbon filter. The filtered smoke
is then recirculated into the room. This system is used if the premise
renders it impossible to install a ducting system.

8
Several things which must be ensured when installing an exhaust hood
with re-circulating system:
1. Both carbon filter and aluminum filter must be
used.
2. The position of both filters must be correct.
3. Holes where air duct is discharged found in
the front cabinet of the exhaust hood cannot
be closed.
Electricity Connection
MODENA Exhaust Hood is designed for 220 Volt electricity input,
single phase with 50 Hz of frequency. This appliance uses a double-
insulated power cord (2 parallel cords) and should not be connected
to a grounding wire.

9
•Connect the power cord with an electrical outlet.
•Slide or press the motor speed regulator button and light switch
to turn vent hood on or off as shown in the following picture.
Touch button
= ON/OFF button
= Speed decrease button
= Display
= Spreed increase button
= Lamp button
To active the Timer, press lamp button and hold for 3 second. The
digital display will be flashing and into 5 minutes countdown. After 5
minutes, the motor and the lamp will be turn off automatically, the buzzer
sound for 1 second.
HOW TO USE
NOTES:
Adjust the motor speed of the vent hood according to the thickness
of smoke/steam generated by the cooking process.
ATTENTION!
•Avoid direct contact between the vent hood and
open flames from the stove.
•To obtain optimum filtering result, turn off the vent
hood 20 –30 minutes after having finished cooking.

10
MODENA Exhaust Hood is specifically designed for long-term usage and
does not require complicated maintenance. However, there are several
things you can do to maintain its quality as follows:
Cleaning the cabinet:
To clean the surface of exhaust hood cabinet from sticky oil particles,
use cloth/sponge and soap water and dry it. The cabinet should be
cleaned after each cooking session.
Cleaning the filter:
Smoke/steam from cooking and oil particles generated by the cooking
procedure will be immediately absorbed by hte filter and therefore must
be cleaned regularly.
Aluminum filter and metal filter:
•For routine usage, clean the aluminum
filter once every 10-15 days by soaking
the filter in a basin filled with soap water
for 1 hour (look at picture) and use a soft
brush to scrub it and then dry the filter
throughly before returning it to its proper
position.
•Aluminum filter can be cleaned using a dishwasher.
•Avoid bending the filter during wash.
Carbon filter
Carbon filter must be replaced with a new one at least once every 4
months or when carbon filter is no longer capable of absorbing the
cooking odor.
•Remove the power cord from the electrical
outlet.
•Open the exhaust hood grid.
•Rotate the carbon filter counterclockwise
and remove the carbon filter
MAINTENANCE

11
•Install the new carbon filter by putting it in position and rotating
it clockwise.
ATTENTION!
Carbon filter cannot be washed and must be replaced with a new
one upon its expiry.

12
Consult the following troubleshooting before contacting our Service
Center regarding your exhaust hood:
Problem
Cause
Solution
Exhaust hood
malfunctioning
•Power cord is not yet
connected to the
electrical outlet.
•Electrical outlet does
not have electricity
current in it.
•Connect the power cord
to the electrical outlet.
•Connect the power cord
to a properly functioning
electrical outlet.
Reduced suction
power
•Dirty aluminum filter.
•Dirty carbon filter.
•Clean the aluminum filter,
dry it and place it back on
the vent hood.
•Replace the carbon filter
with a new one
Motor fan
malfunctioning
•Broken motor coil
•Contact MODENA Service
Center
Motor stops
working after a
while
•Safety thermal
regulator is active.
•The vent hood is installed
too close to the stove
•Air circulation is not
optional
•Contact MODENA Service
Center.
TROUBLESHOOTING

13
Model
RX 9632
RX 7632
Type
Slim hood
Slim hood
Material of cabinet
Stainless
Stainless
Color of cabinet
Stainless
Stainless
Front color
Black
Black
Amount the Motor
2
2
Light
2 LED
2 LED
Control
Touch button
Touch button
Variable speed level
3
3
Kind of filter
Cassette Aluminum Filter
+ Carbon filter
Cassette Aluminum Filter +
Carbon filter
Motor power
2 x 80 W
2 x 80 W
Lamp power
2 x 1.5 W
2 x 1.5 W
Product dimension
(L x D x H )mm
895 x 480 x135
895 x 480 x135
Specifications of this appliance may change without notice to improve
the quality of the product. Figures in this manual are schematic and may
not match your product exactly. Values stated on the machine labels or
in the documentation accompanying it are obtained in laboratory in
accordance with the relevant standards. Depending on operational and
environmental conditions of the appliance, values may vary.
SPECIFICATION

06/21