Modena Doppio Series Owner's manual

User
Manual Book
Water Dispenser
Doppio Series
DD 68

2
Thank you for your trust in choosing MODENA products for your household
needs. With your satisfaction as our priority, we constantly aim to deliver
stylishly designed products equipped with state-of-the-art technology to
assist you in your daily activities.
This is your guidebook containing everything you need to know about our
product. Please reach out to us if you need further assistance or other
information via our Customer Care or our official website www.modena.com.

3
CONTENTS PAGE.
• Introduction 2
• Part 1 : Name of Parts 4
•Part 2 : Installation 5
• Part 3 : How to Use 6
• Part 4 : Maintenance 9
• Part 5 : Precaution Action 9
• Part 6 : Troubleshooting 11
• Part 7 : Specification 11

4
DD 68 L & DD 68 W
* Features and specifications depend on the type of product.
Part 1 : Name of Parts
Back Side
5. Red Switch
6. Fuse
7. Drain Valve
8. Condenser
Front Side
1. Control Panel
2. Water Tap
3. Drip Tray
4. Cabinet Door

5
Please read this operation manual carefully before operating the appliance in order to use the
appliance properly and safely. Pay attention to the entire sign or warning explained on the pictures or
text.
1. Install the dispenser on an even and stable surface. A
minimum distance of 20 cm from the wall must be
provided.
2. Leave the appliance for 1 hour to stabilize the
refrigerant.
3. Insert the Z-pipe into the gallon and then cover it with
the lid.
4. Insert the gallon into the cabinet. Make sure it is
installed properly and close the door.
5. Connect the power cord to the power socket, and turn
on the red switch (heater) located behind the
appliance. Make sure that the socket/electric source
has been grounded to prevent electric leakage. Turn
on the switch located behind the appliance.
6. For initial use, the inside of the appliance must be
cleaned. Press the hot and cold water button. Make
sure the water dispenses out of the tap. After that, wait
around 20 minutes, then remove the gallon and drain
the water by opening the drain valve. Make sure the
power cord is unplugged from the power source when
draining the remaining water.
7. If the gallon is empty, turn off the red switch (heater)
before replacing it with a new one.
Attention :
- This appliance is designed for indoor use.
- Avoid placing the appliance in a humid, wet, and poor electrical installation because it can
cause an electric shock or fire.
- Do not place flammable objects near the dispenser.
- Do not expose the appliance to direct sunlight and rain because it can degrade its
performance and cause electrical leakage hazard.
- Do not connect this dispenser to the source of electric current or pressing the heating button if
there is no water in the tank or no water flows from the hot water tap if the button is pressed.
- Do not modify the power cord on the appliance or connect using extension cord to prevent
risks of short circuit and fire.
- Do not touch the back or the condenser to avoid electric shock.
- During a power outage, after the power returns, wait around 5 minutes before turning the
appliance on.
Part 2 : Installation

6
Control Panel Function
DD 68 L
Front view
Top view
* Features and specifications depend on the type of product.
1. Hot Water Temperature Digital Display
2. Cold Water Temperatur Digital Display
3. Reheating Button
4. Hot Water Set Button
5. Hot Water Indicator
6. Water Level Indicator
7. Cold Water Indicator
8. Cold Water Set Button
9. Cleaning Tank Program Button
10. Hot Water Button
11. Normal Water Button
12. Cold Water Button
Part 3 : How to Use

7
DD 68 W
Front view
Top view
* Features depend on the type of product.
1. Hot Water Temperature Digital Display
2. Cold Water Temperature Digital Display
3. Hot Water Indicator
4. Water Level Indicator
5. Cold Water Indicator
6. Hot Water Button
7. Child Lock
8. Cold Water Button
How to use the dispenser on DD 68 L
-Using the cold water
Connect the power cord to the power source. The appliance will begin the cooling process until the
temperature reaches 5 ℃seen on the display. The appliance will automatically continue the cooling
process if the temperature reaches 10 ℃seen on the display. Cold water temperature can be set to
5 ℃, 8 ℃and 12 ℃. Press the cold water button set until desired temperature is seen on the
display. Wait for several seconds until the display blinks 5 times. Press the button to
dispense the cold water.
-Using the hot water
To use the hot water, press the hot water set button and the indicator light will be on. The
temperature of hot water will start until reached the factory setting temperature of 90 °C. When the
temperature of the hot water decreases, the appliance will automatically raise or stabilize the
temperature until it reaches the factory setting. Hot water temperature can be set to 70 ℃, 80 ℃and
90 ℃. Press the hot water set button until desired temperature is seen on the display. Wait for
several seconds until the display blinks 5 times. To rise the hot water temperature quickly, press the
reheating button. The temperature of the appliance will rise rapidly until 95 °C. Press and hold the

8
button for 3 seconds to dispense the hot water..
-Use the normal water .
Press & hold the normal button the hot water will come out alternately with cold water until
the water is normal.
-Use The Cleaning Tank Program.
This function is used to clean and disinfect the inside of the tank and pipelines. Hold the Cleaning
Tank Button for 5 seconds to activate it. During this process, the heating and cooling function stop
working. The hot water digital display will be off. Only the cold water digital display that will be on.
This process runs for 75 minutes and the indicator light will be on. During this process, do not use
the appliance. It is recommended to run this function at night, especially before the children and
parents rest. After the cleaning process completed, the appliance will cool down for 75 minutes
before it runs normally. If you want to exit before the cleaning process completed, press and hold
the Cleaning Tank Button for about 5 seconds.
Attention:
Do not use the water from that cleaning process. After the process is complete, dispose of the water
in the tank by opening the drain valve.
How to use the dispenser on DD 68 W
-Use the cold water
Connect the power cord to the power source. The appliance will begin the cooling process until the
temperature reaches 5 ℃seen on the display. The appliance will automatically continue the cooling
process if the temperature reaches 10 ℃seen on the display. Press the child lock button and
hold for 3 seconds until the buzzer beeps. Press the button to dispense the cold water. The
cold water function will be locked automatically once the dispensing is done.
-Use the hot water
The temperature of hot water will start until reached the factory setting temperature of 90 °C. When
the temperature of the hot water decreases, the appliance will automatically raise or stabilize the
temperature until it reaches the factory setting. The hot water temperature can not be set. To rise
the hot water temperature quickly, press the reheating button. The temperature of the appliance will
rise rapidly until 95 °C. Press the child lock button and hold for 3 seconds until the buzzer
beep. Press the button to dispense the hot water. The hot water function will be locked
automatically once the dispensing is done
Attention: The temperature of the hot water may cause burns and scalds.

9
1. In order to avoid unwanted incidents, always disconnect from the power cord from the power
source before cleaning the dispenser.
2. This dispenser has been disinfected prior to shipping.
3. Bottle support collar, water tube, and heating element must be cleaned by expert technician once
a year to maintain the machine to its good condition and to extend the appliance’s lifespan. Do
not attempt to disassemble the machine in order to avoid damage to the machine.
4. Use soft and wet cloth to clean the surface of the dispenser. Use soft and dry cloth to dry the
surface. Do not let water enter the appliance’s engine.
5. Make sure the power cord is unplugged from the power source when draining the remaining water
or when in a maintenance or when not in use for a long time. Meanwhile, when the water from the
hot tap is cold, open the drain valve until there is no water in the appliance.
a. Install the dispenser on even surface. Avoid placing it in a humid place. A
minimum distance of 20 cm from the wall must be provided. Do not store
flammable substances near the dispenser.
b. To avoid damage to the machine, avoid connecting power cord or
pressing the heating switch (red) until the hot water comes out of the hot
water tap.
c. If the dispenser won’t be used for a long period, turn off the heating and
cooling switches and disconnect the cord from the power socket and
drain the remaining water through the drainage.
d. Do not use chemical substances or directly pour water to clean the
dispenser. Use soft cloth instead.
e. Do not pull the cord to disconnect the power cord from the power socket.
Hold and unplug it from the head with dry hand.
Part 5 : Precaution Action
Part 4 : Maintenance

10
f. Do not put the dispenser upside down. The inclination should not be
more than 45° to avoid damage to the compressor.
g. The thermostat on the dispenser has been adjusted by the manufacturer.
Do not attempt to modify the thermostat by yourself to avoid unwanted
damage.
h. This appliance is designed for use by adults. Do not allow children to play
with the appliance or let them hang on the door. The appliance may fall
over and harm them. Children should be supervised to ensure that they
don’t play with the appliance. The appliance is not intended for use by
individual (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a
person who is responsible for their safety.
If there is damage to the power cord, contact MODENA Call
Center immediately to do a replacement. The replacement of
power cord must be done by experienced expert and understands
about electricity. Never replace the power cord on your own, due
to the dangers that could lead to harm yourself and others.
Attention!
This appliance must not be disposed of with other household waste. To prevent possible
harm to the environment or human health from uncontrolled waste disposal.
The appliance contains a gas insulation and refrigerant that must be disposed of properly. When you
want to dispose of the appliance, We advise you to consult with authorized service providers so that
they can learn information required and official forms.
Make sure the pipes and duct work of refrigerant of the appliance is not damaged before it was taken
by the disposal personnel.
Consult with authorized service providers to ask everything and issues regarding the appliance. Do
not do or allow others to do anything to the appliance.

11
Please check these following before contacting the Call Center if any problem occurs:
Problem
Possible Cause
Recommended Action
Water is not hot or not cold.
-Excessive usage of hot
water or cold water in a
short period of time.
-The appliance is not yet
connected to electricity.
-Wait until the water
becomes cold or hot.
-Connect the cord to the
power socket and press
the heating and cooling
switches.
Water is not being
dispensed out of the tap.
-Water gallon is empty.
-The pipe is stuck or
blocked by something.
-Replace the water gallon
with a new one
-Turn off the cooling switch.
After 4 hours, turn it back
on.
Leak on the water gallon
support.
-Water gallon is leaking /
damaged.
-Replace water gallon with
a new one.
Loud noise during operation.
-Improper installation or
placement of appliance.
-Install appliance on even
and stable surface.
MODEL
DD 68 L
DD 68 W
Type
Cold, Normal & Hot
Cold & Hot
Lower chamber
Gallon storage
Gallon storage
Color
Black (L)
White (W)
Hot water output (liter/hour)
5
5
Cold water output(liter/hour)
2
2
Hot water tank capacity (liter)
1.7
1.7
Cold water tank capacity (liter)
3.2
3.2
High temperature (celcius)
≥90
≥90
Cold temperature (celcius)
≤10
≤10
Free-CFC compressor
Yes
Yes
Regulator of thermostat
Yes
Yes
Water tube material
Stainless
Stainless
Power (Hot) (watt)
500
500
Compressor power (watt)
85
85
Product dimension (L x W x H) mm
320x355x1050
320x355x1050
Product weight (Kg)
19
19
L= Black V= Silver R= Red G-Gray D= Gold W =White
* Specifications of this unit may change without prior notice to improve the quality of the product.
Pictures in this manual are schematic and may be different from the actual product. Values stated on the machine
labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant
standards. Depending on operational and environmental conditions of the unit, values may vary.
Part 7 : Specification
Part 6 : Troubleshooting

11/20