Modena Pietro Series Owner's manual

User
Manual Book
Water Dispenser
Pietro Series
DD 65 L

2
Thank you for your trust in choosing MODENA products for your household
needs. With your satisfaction as our priority, we constantly aim to deliver
stylishly designed products equipped with state-of-the-art technology to assist
you in your daily activities.
This is your guidebook containing everything you need to know about our
product. Please reach out to us if you need further assistance or other
information via our Customer Care or our official website www.modena.com.

3
CONTENTS PAGE.
• Introduction 2
• Part 1 : Name of Parts 4
•Part 2 : Installation 5
• Part 3 : How to Use 6
• Part 4 : Maintenance 6
• Part 5 : Precaution Action 6
• Part 6 : Troubleshooting 8
• Part 7 : Specification 9

4
DD 65 L
* Features and specifications depend on the type of product.
Note:
Part 1 : Name of Parts
1. Hot Water Button
2. Cold Water Button
3. Normal Water Button
4. Indicator/front panel
5. LED light
6. Reset Button
7. Drip Tray
8. Water Pipe
9. Bottom Cabinet Door
10. Power Cord
11. Cooling Switch
12. Heating Switch
13. Drain Valve
14. Condenser
15. LED Switch Light

5
Please read this operation manual carefully before operating the appliance in order to use the
appliance properly and safely. Pay attention to the entire sign or warning explained on the pictures or
text.
1. Install the dispenser on an even and stable surface. A minimum
distance of 20 cm from the wall must be provided.
2. Leave it for 1 hour to stabilize the refrigerant.
3. Insert the pipe into the gallon and then cover it with the lid.
4. Insert the gallon into the cabinet and close the door.
5. Connect the power cord to the power socket, and turn on the red
switch (heater) located behind the appliance. Make sure that the
socket/electric source has been grounded to prevent electric
leakage. Turn on the switch located behind the appliance.
6. For initial use, the inside of the appliance must be cleaned.
Press the hot and cold water button. Make sure the water
dispenses out of the tap. After that, wait around 20 minutes,
then remove the gallon out of the storage and empty the
water by opening the drain valve. Make sure the power cord
is unplugged from the power source when draining the
remaining water.
Attention :
-This appliance is designed for indoor use.
-Make sure the pipe is installed properly and the cabinet doors closed
securely
-When the water in the gallon is empty, turn off the red switch
(heating) before replacing it with a new one.
-Avoid placing the appliance in a humid, wet and poor electrical installation because it can cause
an electric shock or fire.
-Do not place flammable objects near the dispenser.
-Do not expose the appliance to direct sunlight and rain because it can degrade its performance
and cause electrical leakage hazard.
-Do not connect this dispenser to the source of electric current or pressing the heating button if
there is no water in the tank or no water flows from the hot water tap if the button is pressed.
-Do not modify the power cord on the appliance or connect using extension cord to prevent risks
of short circuit and fire.
-Do not touch the back or the condenser to avoid electric shock.
-During a power outage, after the power returns, wait around 5 minutes before turning the
appliance on.
Part 2 : Installation

6
How to use a dispenser with three taps:
-To dispense the hot water, push the left button.
-To dispense the normal-temperature water, push the middle button.
-To dispense the cold water, push the right button.
The appliance is equipped with a safety on hot water button to prevent the danger of the reach of
children. Scroll and press the button to dispense hot water.
If the red indicator light is on, it indicates that the process of heating water is running. If the blue
indicator light is on, it indicates that the process of cooling water in the tank is running.
If the yellow indicator light is on, this indicates the gallon water is empty. Replace with a new one
immediately. The indicator light will turn off when the new galon is replaced. The appliance will run
normally.
Attention:
-Beware! Avoid hazard of hot water.
-Cabinet door should be closed. If not, the pipe will not work out.
1. In order to avoid unwanted incidents, always disconnect the power cord from the power source
before cleaning the dispenser.
2. This dispenser has been disinfected prior to shipping.
3. Water pipe, water tank, and heating element must be cleaned by expert technician once a year to
maintain the machine to its good condition and to extend the appliance’s lifespan. Do not attempt
to disassemble the machine in order to avoid damage to the machine.
4. Use soft and wet cloth to clean the surface of the dispenser. Use soft and dry cloth to dry the
surface. Do not let water enter the appliance’s engine.
5. Make sure the power cord is unplugged from the power source when draining the remaining water
or when in a maintenance or when not in use for a long time. Meanwhile, when the water from the
hot tap is cold, open the drain valve until there is no water in the appliance.
1. Install the dispenser on even surface. Avoid placing it in a humid place.
A minimum distance of 20 cm from the wall must be provided. Do not
store flammable substances near the dispenser.
Part 5 : Precaution Action
Part 4 : Maintenance
Part 3 : How to Use

7
2. To avoid damage to the machine, avoid connecting
electrical cord or pressing the heating switch (red) until
the hot water comes out of the hot water tap.
3. If the dispenser won’t be used for a long
period, turn off the heating and cooling switches and
disconnect the cord from the power socket and drain the remaining water
through the drainage.
4. Do not use chemical substances or directly pour water to
clean the dispenser. Use soft cloth instead.
5. Do not pull the cord to disconnect the power cord
from the power socket. Hold and unplug it from the head with dry
hand.
6. Do not put the dispenser upside down. The inclination should not be
more than 45° to avoid damage to the compressor.
7. The thermostat on the dispenser has been
adjusted by the manufacturer. Do not attempt to
modify the thermostat by yourself to avoid
unwanted damage.
8. This appliance is designed for use by adults. Do not allow children to
play with the appliance or let them hang on the door. The appliance may
fall over and harm them. The appliance is not intended for use by
individual (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a
person who is responsible for their safety.

8
If there is damage to the power cord, contact MODENA Call
Center immediately to do a replacement. The replacement of
power cord must be done by experienced expert and understands
about electricity. Never replace the power cord on your own, due
to the dangers that could lead to harm yourself and others.
Attention!
This appliance must not be disposed of with other household waste. To prevent possible
harm to the environment or human health from uncontrolled waste disposal.
The appliance contains a gas insulation and refrigerant that must be disposed of properly. When you
want to dispose of the appliance, We advise you to consult with authorized service providers so that
they can learn information required and official forms.
Make sure the pipes and duct work of refrigerant of the appliance is not damaged before it was taken
by the disposal personnel.
Consult with authorized service providers to ask everything and issues regarding the appliance.
Do not do or allow others to do anything to the appliance before asking the official service providers.
Please check these following before contacting the Call Center if any problem occurs:
Problem
Possible Cause
Recommended Action
Water is not hot or not cold.
-Excessive usage of hot
water or cold water in a
short period of time.
-The appliance is not yet
connected to electricity.
-Wait until the water
becomes cold or hot.
-Connect the cord to the
power socket and press
the heating and cooling
switches.
Water is not being
dispensed out of the tap.
-Water gallon is empty.
-The pipe is stuck or
blocked something.
-Replace the water gallon
with a new one
-Turn off the cooling switch.
After 4 hours, turn it back
on.
Leak on the water gallon
support.
-Water gallon is leaking /
damaged.
-Replace water gallon with
a new one.
Loud noise during operation.
-Improper installation or
placement of appliance.
-Install appliance on even
and stable surface.
Buzzer is still ringing after
changing the water gallon
-There is a problem with
the reset button
-Unplug out the power cord
then plug in again.
Part 6 : Troubleshooting

9
MODEL
DD 65 L
Type
Cold, Hot & Normal
Bottom Loading
Gallon storage
Color
Black
Hot water output (liter/hour)
2
Cold water output(liter/hour)
1.5
High temperature (Celsius)
≥90
Cold temperature (Celsius)
≤10
Free-CFC compressor
Yes
Regulator of thermostat
Yes
Water tube material
Stainless
Heating Power (watt)
190
Compressor power (watt)
80
Product Dimension (L x W x H) mm
325 x 370 x 1040
Product weight (Kg)
15
L= Black V= Silver R= Red D= Gold W =White
* Specifications of this appliance may change without prior notice to improve the quality of
the product. Pictures in this manual are schematic and may be different from the actual product.
Values stated on the machine labels or in the documentation accompanying it are obtained in
laboratory in accordance with the relevant standards. Depending on operational and environmental
conditions of the appliance, values may vary.
Part 7 : Specification

11/20