MOTECK CIS3 User manual

1
User Guide
Specification
- Input voltage: 24V DC
- Output voltage: 24V DC
- Max. current: 10A per channel
- Max. number of actuators: 2 channels
- Synchronization for 2 actuators
- Overload protection (each actuator independently): 13A Max.
- Controlled by HM6R handset
- Work with potentiometer positioning feedback
- Duty cycle: 10%, max. 2 min. continuous operation in 20 min.
www.moteck.com
CIS3 Control Box
Hand control
Actuator 2
Actuator 1
Connection Diagram
I/O introduction PCBA
Actuator 2GND
24V DC IN
Actuator 1
With potentiometer feedback (example of ID10 or ID10S actuators)
Actuator
Remarks:
Wires color definition may be different from each actuator model; please refer to data sheet of each actuator for wires details.
1
Signal Power
Pin
Definition
Wires color
1 2 3 4 5
Yellow
2
Blue
3
White
4
Red
5
Black
GND M-
DataVCC M+

Hand Control Operation Guide
2
©2018 Aug. MOTECK. MO-IND-I-0002 Version: 1.2
Socket
Store function
M1 + M2 Down (synchronous)
M1 + M2 UP (synchronous)Memory position 1
Memory position 2Memory position 3
GND
7-pin socket
Store function
GND
Memory position 1
Memory position 3
M1+M2 Down (synchronous)
M1+M2 UP (synchronous)
Memory position 2
7-pin DIN plug
VCC
VCC
The hand control compatible with CIS3 control box has the same steps of system learning and button functions.
(HM6R is used as an example here.)
Press and at the same time until the actuators start to move.
The learning is done after both actuators move to the fully retracted position.
System learning through hand control:
1. Extend both actuators synchronously.
2. Retract both actuators synchronously.
3. Press button until the LED is OFF, and press button , or to store the needed position.
(LED will now blink for 1 times to confirm the positions is stored)
4. Drive both actuators toward the stored position .
5. Drive both actuators toward the stored position .
6. Drive both actuators toward the stored position .
Function:
Hand control socket for Moteck F-type DIN plug
- 2 drives model
F-type
HM6R

1
使用者說明書 www.moteck.com
CIS3 控制盒
產品規格
- 輸入電壓：24V DC
- 輸出電壓：24V DC
- 保護電流：10A (每支推桿)
- 推桿插孔數：最多2
- 同步功能
- 過載電流保護(每支推桿各自獨立)：13A Max.
- 可搭配HM6R手控器
- 帶有電位器定位反饋
- 工作週期：10% 最長可連續操作2分鐘
接線說明
I/O 連接埠說明 PCBA
推桿 2
GND
24V DC IN
手控器
推桿 2
推桿 1
配備電位器定位反饋 (以ID10或ID10S推桿為例)
推桿
備註:
每種推桿的線芯顏色不全然相同，請參照各推桿規格文件的線芯顏色.
1 2 3 4 5
推桿 1
3 5
訊號線 電源線
編號
接線定義
線芯顏色 白色 黑色
2
藍色
1
黃色
4
GND M-
DataVCC M+
紅色

2
©2018 Aug. MOTECK. MO-IND-I-0002 Version: 1.2
F型式
插座
存儲功能
M1 + M2 縮回(同步)
M1 + M2 伸出(同步)位置記憶1 位置記憶2位置記憶3
GND
7-pin插座
VCC
存儲功能
GND
位置記憶1
位置記憶3
M1+M2 縮回(同步)
M1+M2 伸出(同步)
位置記憶2
7-pin插頭
VCC
手控器按鍵功能說明
相容CIS3控制盒的手控器，手控器學習和功能都一樣 (此以HM6R手控器為範例)
手控器學習:
功能:
手控器插座配Moteck F型式DIN插頭線芯定義
- 驅動2支推桿
同時按 2秒，2支推桿會同時伸出到頂，再縮回到底，即完成學習步驟.
1. 2支推桿同時伸出
2. 2支推桿同時縮回
3. 按壓 鍵超過兩秒，此時LED燈熄滅，再按下所要記憶的位置 、 或 ，
此時LED燈會閃一下以表示此位置已被記憶.
4. 按下按鍵 ，推桿伸出到已記憶的位置 .
5. 按下按鍵 ，推桿伸出到已記憶的位置 .
6. 按下按鍵 ，推桿伸出到已記憶的位置 .
HM6R