MOTECK ID10 User manual

www.moteck.com
Technical changes may be made to improve the product without notice！
2022.04_V2.0
Revision
Actuator
ID10

www.moteck.com
1
CAUTION
The load should be centered on the
operating direction.
Side load is NOT good for actuators.
KG
Side Load
KG
Load
●
●
●
Be sure that the load acts on the actuator in the axial direction and it isn't recommended to have
side load acts on the actuator.
If the actuator is jammed by an obstruction or the load is severely overweight, the actuator's clutch
protection device will trip and run idly to protect the actuator or the customer's mechanical
equipment from damage. However, once the clutch trips, it will cause the actuator's stroke range to
deviate from the original factory settings and affect normal use. Please be careful to avoid
obstructions and do not exceed the rated load of the actuator. If it is found that the clutch has
tripped and the stroke setting is abnormal, immediately stop using the actuator before the
equipment is damaged, and contact the local agent or service center for assistance.
Users are forbidden to open the outer cover of the limit switch so as not to affect the original
protection level of the actuator, resulting in the immediate failure of the original factory protection
commitment.

www.moteck.com
2
MANUAL DRIVE (MD) CONNECTOR
The MD (manual drive) is an alternative way to drive the motor directly, if the power is not available.
Step 1. Remove the plug on the gearbox cover.
Step 2. Use a 8.0mm hex bit or electric screwdriver (recommended) to drive the gear directly.
Step 3. Insert the plug into the hole, and confirm the plug is installed properly.
● The Max. drive torque is 6kg-cm with 4500N load.(Ball Screw)
Gear
Plug

www.moteck.com
3
WIRE CONNECTION
For ID10 actuator, connection rule of power wires varies according to different types and gear ratio(s).
Please follow the instructions below.
Definition
GND
Red
Black
Wire color
Blue
Comments
Voltage input range: 3.5 ~ 20VVin
White
Hall effect sensor resolution: 20ppi, 1.27mm/pulse (0.787pulses/mm)
High= 10.8V (±0.6V)
Low= GND
Hall signal data:
Signal
wires
Hall outputYellow
● With single Hall effect sensor positioning feedback
● Standard (without Limit switch nor positioning feedback)
Gear ratio: 5:1, 10:1, 20:1
Gear ratio: 30:1, 40:1
Red
Black
Wire color CommentsDefinition
Red
Black
Wire color CommentsDefinition
● With Limit switches
Red
Black
Wire color CommentsDefinition
Connect red wire to “Vdc +” & black wire to “Vdc -“ of DC power to
extend the actuator. Switch the polarity of DC input to retract it.
DC Power
Power
wires
Connect red wire to “Vdc -” & black wire to “Vdc +“ of DC power to
extend the actuator. Switch the polarity of DC input to retract it.
DC Power
Power
wires
Connect red wire to “Vdc +” & black wire to “Vdc -“ of DC power to
extend the actuator. Switch the polarity of DC input to retract it.
DC Power
Power
wires
DC Power
Power
wires
Connect red wire to “Vdc +” & black wire to “Vdc -“ of DC power to
extend the actuator. Switch the polarity of DC input to retract it.
Hall
Low
High

www.moteck.com
4
●With Potentiometer (POT) absolute positioning feedback
Connect red wire to “Vdc +” & black wire to “Vdc -“ of DC power to
extend the actuator. Switch the polarity of DC input to retract it.
Power
wires
Comments
Input voltage 70V max.
1. Potentiometer specification:
- 10K ohm, 10 turns.
- Tolerance ±5%
2. Output voltage: The voltage (resistance) between
Blue and White increases linearly from about 0 when
the actuator extends, and decreases when it retracts.
3. There are different resolutions according to the stroke length
(as table below)
Definition
DC Power
GND
Vin
Red
Black
Wire color
White
Yellow
SAFETY DECLARATION
This appliance cannot be used by children or persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction.
MOTECK MO-I-0002-V2.0
Terms of Use
The user is responsible for the suitability of MOTECK products, and the products listed on the MOTECK website are subject to change without notice. MOTECK reserves the right to terminate sales or
delete any products displayed on the website or listed in its catalog.
Actuator extends
Y
W
B
153 (6”)
102 (4”)
203 (8”)
Stroke (mm)
254 (10”)
305 (12”)
457 (18”)
610 (24”)
0.3 ~ 8.1K
0.3 ~ 8.7K
0.3 ~ 9.2K
0.3 ~ 7.4K
0.3 ~ 8.8K
Resistance (tolerance: ±0.3KΩ)
0.3 ~ 9.4K
0.1 ~ 9.9K
POT outputBlue
Signal
wires