Motorline professional MC60 Use and care manual

v3.0
REV. 06/2021
MC60MC60 EN
USER’S AND INSTALLER’S MANUAL

2A 2B
A
B

B



A

A
B
A
A
B
A
B
A
A
B
B
A
A
B
B
A
A
B
B
B
A
A
B


A


ENEN
INDEX INDEX
. CONTENT . CONTENT
. SAFETY INSTRUCTIONS
. CONTROL BOARD
. CONEXION SCHEME
. INSTALLATION
. PROGRAMMING "P"
. PROGRAMMING "E"
. DISPLAY
. CONEXION SCHEME
CHARACTERISTICS
SLIDING GATES [SC]
BUTTONS AND LEDs
BARRIERS [BR]
AUTOMATIC PILLARS [PL]
MASTER-SLAVE
CONNECTORS
SECTIONAL DOORS [SE]
BASE INSTALLATION PROCESS
TRANSMITTERS
FUNCTIONS
EXCLUSIVE FACTORY VALUES
"P" MENUS
"E" MENUS
P0COURSE PROGRAMMING
P1DECELERATION TIME ADJUSTMENT
E2COURTESY LIGHT TIME
P7OPERATING LOGIC
P4PAUSE TIME
P2SETTING DOWN TIME
E3FOLLOW ME
E4COURSE TIME ADJUSTMENT
P8FLASHING LIGHT
P5PHOTOCELLS 1 PROGRAMMING
E7MANUEVERS COUNTER
E0PRESENT MAN
P3PEDESTRIAN COURSE TIME
E5BRAKE/LOCK/PUSH
P9REMOTE PROGRAMMING
P6PHOTOCELLS 2 PROGRAMMING
E8RESET  RESET FACTORY VALUES
E9RGB OUTPUT
E1SOFT START
DISPLAY INDICATIONS
CONEXIONS MAP
E6DECELERATION SPEED

3EN
GENERAL WARNINGS
•This manual contains very important safety and usage
information. very important. Read all instructions carefully
before beginning the installation/usage procedures and keep
this manual in a safe place that it can be consulted whenever
necessary.
•This product is intended for use only as described in this manual.
Any other enforcement or operation that is not mentioned is
expressly prohibited, as it may damage the product and put
people at risk causing serious injuries.
•This manual is intended firstly for specialized technicians, and
does not invalidate the user’s responsibility to read the “User
Norms” section in order to ensure the correct functioning of the
product.
•The installation and repair of this product may be done by
qualified and specialized technicians, to assure every procedure
are carried out in accordance with applicable rules and norms.
Nonprofessional and inexperienced users are expressly
prohibited of taking any action, unless explicitly requested by
specialized technicians to do so.
•Installations must be frequently inspected for unbalance and
the wear signals of the cables, springs, hinges, wheels, supports
and other mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of
parts, the product must be disconnected from power supply.
Also including any operation that requires opening the product
cover.
•Theuse,cleaningandmaintenanceofthisproductmaybecarried
out by any persons aged eight years old and over and persons
whose physical, sensorial or mental capacities are lower, or by
. SAFETY INSTRUCTIONS
ATTENTION:
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that
the product and electronic accessories (eg. Charger, USB
cable, electronic material, controls, etc.) should not be
disposed of as other household waste at the end of its
useful life. To avoid possible harm to the environment or
human health resulting from the uncontrolled disposal
of waste, separate these items from other types of waste
and recycle them responsibly to promote the sustainable
reuse of material resources. Home users should contact
the dealer where they purchased this product or the
National Environment Agency for details on where and
how they can take these items for environmentally safe
recycling. Business users should contact their vendor
and check the terms and conditions of the purchase
agreement. This product and its electronic accessories
should not be mixed with other commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
the product and observe all safety procedures in this
manual.

4EN
persons without any knowledge of the product, provided that
these are supervision and instructions given by persons with
experienced in terms of usage of the product in a safe manner
and who understands the risks and dangers involved.
•Children shouldn’t play with the product or opening devices
to avoid the motorized door or gate from being triggered
involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that
you have all the devices and materials necessary to complete
the installation of the product.
•You should note your Protection Index (IP) and operating
temperature to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know
how to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door,
a door locking mechanism must be installed while the gate is in
motion.
•Do not install the product “upside down” or supported by
elements do not support its weight. If necessary, add brackets
at strategic points to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting,
transport and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify
if the necessary mechanical stops are in the appropriate places.
•The central must be installed on a safe place of any fluid (rain,
moisture, etc.), dust and pests.
•You must route the various electrical cables through protective
tubes, to protect them against mechanical exertions, essentially
on the power supply cable. Please note that all the cables must
enter the central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m
from the ground or other level of access, the minimum safety
and health requirements for the use of work equipment workers
at the work of Directive 2009/104/CE of European Parliament
and of the Council of 16 September 2009.
•Attach the permanent label for the manual release as close as
possible to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the
electrical panel, must be provided on the product’s fixed power
supply leads in accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac
or 110Vac, ensure that connection is to an electrical panel with
ground connection.
•The product is only powered by low voltage satefy with central
(only at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever
necessary.
•If the product has contact with fluids without being prepared,
it must immediately disconnect from the power supply to avoid
short circuits, and consult a specialized technician.
•Ensure that technician has provided you the product manual
and informed you how to handle the product in an emergency.
•If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety
conditions have been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker
or replacing the fuse. If the malfunction is not repairable by
. SAFETY INSTRUCTIONS . SAFETY INSTRUCTIONS

5A 5B
ENEN
The MC60 is a control board with built-in radio control system, developed for the
automation of sliding, sectional gates, barriers or 24V electromechanical pillar.
• Power Supply 24V AC/DC
• Flashing light’s output 24VDC 4W Max.
• RGB Lightbulb’s output 24Vdc 100mA Máx.
• Motor’s output 24Vdc 180W Máx.
• Auxiliary accessories output 24V DC 8 W Máx.
• Security and BT transmitters 24V DC
• Working temperature -25°C a + 55°C
• Incorporated Radio Receptor 433,92 Mhz
• OP Transmitters 12bits or Rolling Code
• Maximum Memory Capacity 100 (full opening) - 100 (pedestrian opening)
• Control Board Dimensions 130x107 mm
consult this manual, contact a technician.
•Keep theoperationareaof themotorized gate freewhilethe gate
in in motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges
if the product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper
installation use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
. SAFETY INSTRUCTIONS CHARACTERISTICS . CONTROL BOARD
107mm
130mm

6A 6B
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
1
ANT
2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
BG R Y V+
LK
LO FCF0 LE
LS LBLA
ANT
ENEN
VAC 01 • Power Supply Input - 20Vdc
02 • Power Supply Input - 20Vdc
BATT 01 • 24Vdc Input for Emergency Bettery 02 • COM Input (Solar Panel ou Emergency Bettery)
03 • 24Vdc Input for Solar Panel
LAMP 01 • 24Vdc Flashing light's Output (max 4W)
02 • 0V Flashing light's Output
MOT1 01 • 24Vdc Motor Output (max 180W)
02 • 24Vdc Motor Output (max 180W)
V+ 01 • 24Vdc power supply output for accessories (max 8W)
02 • 0V power supply output for accessories
LK 01 • 24Vdc ElectricLock Output (max 12W)
02 • 0V ElectricLock Output
LO 01 • Full Pulsing Input (NO)
LS 01 • Pedestrian Pulsing Input (NO)
FO 01 • Closing limit-switch input
FC 01 • Opening limit-switch input
LE 01 • Exterior Photocells (NC)
LA 01 • Interior Photocells (NC)
LB 01 • NC input for emergency device
ANT 01 • Antenna
02 • GND
MENU • Access the Menu
CMD • Commands programmation
UP • Navigate through menus/values
DW • Navigate through menus/values
LO • LED ON when the full button is active
LS • LED on when the pedestrian button is
active
FO • LED OFF when the opening limit switch
is active
FC • LED OFF when closing limit switch is
active
LE • LED OFF when the signal from the
exterior photocells is interrupted
LA • LED OFF when the signal from the
interior photocells is interrupted
LB • LED OFF when the safety button is
active
BT • LED ON when the battery is connected
upside down
VDD • LED ON when power is supplied to the
microcontroller
CONNECTORS
. CONTROL BOARD BUTTONS AND LEDs . CONTROL BOARD

7
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
~ ~
V+
R
G
B
RG
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
EN
SLIDING GATES [SC]
. CONEXION SCHEME
• Motor
• Flashing Light
• Bateries
or or
• Electric Lock
• Photocells
•
Limit switch
• Pushbutton or
Key Selector (total)
• Pushbutton or Key Selector (pedestrian)
CLOSE
OPEN
• RGB Flashing Light
• Transformer
230Vac
120W Máx.
• Fuse
230Vac: 2Ah
115Vac: 3Ah
• Power supply

8
COM
NC
NC
2
3
4
5
6
7
1
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
2
3
4
5
6
7
1
ON
1 2
ANT
STRSECSIGNL R G B + -
A1
A2
9
8
2
3
4
5
6
7
1
~ ~
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
EN
SECTIONAL DOORS [SE]
. CONEXION SCHEME
• Limit Switches Connections
• Transformer connections
• Motor
• Dock leveler
• Magnetic contact
• MX13
• MR13
OPTIONAL (security service)
• Relay
• 12V 7A Battery
• Flashing Light
• Electric Lock
• Photocell
• Maneuvering board
White
Green
Orange
Blue
Brown
Gray
Black

9
12V+
1 2 3
BI RI
4 5 6
GI RGI SEI
8 97
SEO
1 2
RGOROBO
2 3 4 51
GOV+
LGHI SEO
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
~ ~
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
EN
BARRIERS [BR]
. CONEXION SCHEME
• Barrier cover
• LED strip
(Flashing Light)
• Motor
• Barrier
• Transformer
230Vac
120W Máx.
• Fuse
230Vac: 2Ah
115Vac: 3Ah
Blue
Brown
• MC60 control board
(Interior of the barrier)
•
Limit switch
• Safety band
(Optional)
• Fita LED
(Haste)
• Power supply
12VDC
36 W
• Módulo MP106
• MP106 module
in the interior
OPEN
CLOSE
In case of inversion of the rod,
replace the blue wire with the
brown and the micro of the
limit switches, marked by 1
and 2.
• Photocells
• Power supply

10
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
LIGHT
VR1
+-
SEL SET
MONO TEMP. I.CMD
12V24V 0V
M1 M2 FLH FC 24v
24v
RGB
R
G
B
GND
GND
~ ~
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
EN
AUTOMATIC PILLARS [PL]
. CONEXION SCHEME
• Pillar
• MSC50
• Photocells
• 12V Battery
O MSC50 is a twilight sensor.
When turned on, the LEDs will
operate only during the night,
remaining off during the day.
If you want them to always
be connected, make a bridge
(shunt) between the "↓" and
LB of the MC60 control panel.
The use of photocells or a
magnetic loop is essential
to ensure the safety of the
automation.
• LED strip
If the LED strip
is 12V, there
must be a resistance
of 180 Ohms/5 watts
in series with the 24V
of the relay module.
• Module
If limit switches are not used,
Shunt the FO - FC - ↓ inputs.
Red
Yellow
Black
Green
• Transformer
230Vac
120W Máx.
• Fuse
230Vac: 2Ah
115Vac: 3Ah
• Power supply

11
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
BG R Y V+
LK LO V+ FCF0 LE LS LBLA
LAMP MOT1 SP
24v
BATT
20V
VAC
ANT
~ ~
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
EN
MASTER - SLAVE
. CONEXION SCHEME
Brown
Brown
Blue
• Limit switch
• Limit switch
Blue
• Transformer
230Vac
120W Máx.
• Transformer
230Vac
120W Máx.
• Fuse
230Vac: 2Ah
115Vac: 3Ah
• Fuse
230Vac: 2Ah
115Vac: 3Ah
• Power supply
• Power supply
OPEN
CLOSE
• Photocells
The function parameters marked below must respect these values:
NOTE
• The value selected in P7 must be the same in both control boards.
MASTER
P7=00 or 02
E9=0
SLAVE
P4=0
P5 LE=0 P6 LA=0
P7=00 or 02 E0 PL=01
OPEN
CLOSE

12A 12B
ENEN
01 • Connect all accessories according to the connections diagram.
02 • Connect the control board to a 20V power supply
03 • Check if the gate movement is the same as shown on the display:
04 • Make a course programming - menu P0 (page 14B).
05 • If necessary, adjust the deceleration time of the gate at opening and closing - menu
P1 (page 15A).
06 • Adjust the gate force - menu P2 (page 15A).
07 • Re-program the course - menu P0 (page 14B).
08 • Enable or disable the use of Photocells in menu P5 and P6 (page 16A and 16B).
09 • Program a Transmitter (page 12B).
The control board is now fully configured!
Check the pages of the menu programming if you want to configure other features of the
Control board.
CLOSE OPEN
If the display does not match the
movement of the gate, switch off the power
supply center and change the wires of
Motor (0 and 0) .
The installation process assumes that the gate already has mechanical or
electrical limit switches installed. For more information read the motor's
manual.
BASE INSTALLATION PROCESS
. INSTALLATION
05 • Press cmd for 3 sec
and the location will be
empty.
The display will blink
and the position will
be free.
02 • The display will show
dL, confirming that all
commands have been
erased.
01 • Press the cmd button
for 5 sec.
01 • Press the
cmd button for
1 sec.
Transmitter programming for total opening. Transmitter programming for pedestrian opening.
02 • Select (SU or
SP) use↓↑.
03 • Press cmd
once to confirm.
(SU or SP).
04 • Use ↓↑
to select the
transmitter
location you want
to delete.
04 • The first free
position appears.
05 • Press the command
button you want to
program. The display will
blink and move to the
next free location.
03 • Press cmd
once to confirm.
(SU or SP).
01 • Press the
cmd button for
1 sec.
02 • Select the
function where you
want to program
the commands (SU
or SP) use ↓↑.
• PROGRAMMING TRANSMITTERS
• ERASE ALL THE TRANSMITTERS
• ERASE TRANSMITTERS
•If you do not press any key for 10 sec.
the control board will return to standby
• Whenever you store or delete a
the display will flash and show the next
position. You can add or delete commands
without needing back to point 01.
TRANSMITTERS
. INSTALLATION

13A 13B
ENEN
1 • To access the P menu press the MENU key for 1 sec.
2 • Use ↓↑ to navigate through the menus.
3 • Press MENU when you want to confirm access to a menu.
4 • Press ↓↑ simultaneously to exit programming.
1 • To access the E menu press the MENU key for 5 sec.
2 • Use ↓↑ to navigate through the menus.
3 • Press MENU when you want to confirm access to a menu.
4 • Press ↓↑ simultaneously to exit programming.
1 2
3 4
The functions of the plant are divided into 2 areas:
FUNCTIONS
. INSTALLATION
We can only go into programming with the gate electrically stumbled.
"P" MENU
"E" MENU
"P" MENUS
. INSTALLATION
1 2
3 4
MENU FUNCTION MAX. MIN.
PROGRAMMABLE STATE FACTORY VALUE PAGE
Course Programming -
Automatic Programming
-14B
Manual Programming
Slide gates
Sectioned gates
Electromechanical barriers
Bollard
Time adjustment 0s
min. max.
9.9s
Opening deceleration
Closing deceleration See
table
p.A 15A
Time ramp at the opening
Time ramp at the closing
Force and sensibility
adjustment
min. max.
9
0Force Adjustment in Opening
Force Adjustment in Closing
Sensitivity adjustment
See
table
p.A 15A
Pedestrian Course
time 99s0s
min. max. Time setting in pedestrian mode s 15B
Pause time
99s
min. max.
0s
Full closing pause time adjustment
Pedestrian lock pause time adjustment s 15B
Photocells 
programming -
Disables
Ative 
16A
In Opening
In Closing 01
Invert
Stop
Invert 2 sec. and Stop 
Photocells 
programming -
Disables
Ative 
16B
In Opening
In Closing 
Invert
Stop
Invert 2 sec. and Stop 01
Disables security band input
Activates security band input 
Operating logic -Automatic mode function
Step by step mode
Condominium mode function 01 16B
Flashing light -Flashing (opening and closing)
Step by step mode
Courtesy light
 17A
Remote programming -Distance PGM OFF
Distance PGM ON  17A
EXCLUSIVE FACTORY VALUES
. INSTALLATION
MENU SUB-MENU SC SE BR PL
   
   



- 1 1  
 1  


  1 

14A 14B
ENEN
MENU FUNCTION MAX. MIN.
PROGRAMMABLE STATE FACTORY VALUE PAGE
Present Man -
Desactivates present man
Activates present man 00
17B
Disables push buttons mode
Activates push buttons mode 00
Disables emergency device input
Activates input for
Emergency
Active input for twilight sensor
00
Soft start -Deactivates Soft start
Activates Soft start  18A
Courtesy light
time
min. max.
0
99
Courtesy light time adjustment  18A
Follow me -
Desactivates follow me
00 18B
Activates follow me (fully open)
Activates follow me (in open or fully open
position)
Course time
adjustment
min. max.
4m
1m Opening course time (minutes) 00
18B
min. max.
59s
0s Opening course time (seconds) 10s
min. max.
4m
1m Closing course time (minutes) 
min. max.
59s
0s Closing course time (seconds) s
Brake/Lock/
Strokes -
Disables electronic brake
Active electronic brake 
19A
Activates lock on opening
Activates lock with polarity
See
table
p.A
Deceleration
Speed
min. max.
9
0Adjusting the slowing down at the opening
Adjusting the slowing down at the closing
See
table
p.A 19A
Manuevers
counter -Shows the number of maneuvers -19B
Reset - Restore
factory settings -Deactivated
Reset activated  20
RGB Output -Continued output
Intermittent output  20
"E" MENUS
. INSTALLATION COURSE PROGRAMMING . PROGRAMMING "P"
Automatic course scheduling
This menu allows you to
automatic engine
programming and slowdown.
To cancel the programming
press the UP and DOWN keys
simultaneously.
You can use the Controller
instead of the MENU key.
Manual course programming
This menu allows
manually program the
engine and slow down.
System type
This menu allows you to
program the type of system
with which the plant will work.
Sliding doors:
Emergency device disabled
Disables func. pushbutton
Ramp time at opening to 0
Ramp time at closing to 0
Activates lock on opening
Sectioned doors:
Emergency device activated
Disables func. pushbutton
Ramp time at opening to 0
Ramp time at closing to 0
Activates lock with polarity
Automatic programming:
01 • Press MENU for 1 sec.
until it appears .
02 • Press MENU once until
it appears .
03 • Press MENU to start
automatic programming.
The following maneuvers
will be carried out:
a • Closes in slowdown
b • Opens 4 sec. at normal
speed.
c • Closes in slowdown
d • Fully opens at normal
speed.
e • Closes 4 sec. at normal
speed.
f • Opens in slowdown.
g • Closes total at normal
speed.
Manual programming:
01 • Press MENU for 1 sec.
until it appears .
02 • Press MENU once until
it appears .
03 • Press UP until it
appears .
04 • Press MENU to start
programming the opening
time.
05 • Press MENU to
start programming the
slowdown time at the
opening.
06 • Press MENU to start
programming the closing
time.
07 • Press MENU to
start programming the
slowdown time at closing.
08 • Press MENU to finish
programming.
Electromechanical barriers:
Emergency device disabled
Disables func. pushbutton
Ramp time at opening to 3
Ramp time at closing to 3
Activates lock on opening
Bollard:
Output to
Disables func. pushbutton
Ramp time at opening to 3
Ramp time at closing to 3
Activates lock on opening
Programming system type:
01 • Press MENU for 1 sec.
until it appears .
02 • Press MENU once until it
appears .
03 • Press UP until it appears
.
04 • Press MENU to select one
of the systems.

15A 15B
ENEN
DECELERATION TIME ADJUSTMENT
01 • Press MENU for 2 sec. until appears .
02 • Use UP until appears .
03 • Press MENU will appear . Use UP or DW to navigate the parameters.
04 • Press MENU to edit the chosen parameter value.
05 • The factory set time appears. Use UP and DW to change the value.
06 • Press MENU to save the new value.
This menu allows to set the deceleration time at opening and closing.
Opening slowdown
Allows to set the time that the gate will act
with slowdown in the opening.
(Default value 3)
Closing slowdown
Allows to set the time that the gate will act
with slowdown in the closing.
(Default value 3)
Time ramp at the opening
Allows to set the deceleration ramp time at
the opening.
(Default value: SC=00; SE=00; BR=25; PL=30 )
Time ramp at the closing
Allows to set the deceleration ramp time at
the closing.
(Default value: SC=00; SE=00; BR=25; PL=30 )
. PROGRAMMING "P"
0s
min. max.
9.9s
AJUSTE DO TEMPO DE ABRANDAMENTO
. PROGRAMMING "P" FORCE AND SENSIBILITY ADJUSTMENT
A very low value in this parameter may cause the engine to not have enough
torque to move the gate.
Opening force adjustment
Allows to set the force that
is injected into the openin-
gwhen the engine moves at
normal speed.
Closing force adjustment
Allows to set the force that
is injected into the closing
when the engine moves at
normal speed.
Sensibility adjustment
Allows to adjust the
sensitivity of the engine in
the presence of obstacles.
The higher the sensitivity,
the less effort it will take
to detect any obstacle and
reverse direction.
min. max.
9
0
(Default value:
SC=05; SE=05; BR=09; PL=05 )
min. max.
9
0
(Default value:
SC=05; SE=05; BR=09; PL=05 )
min. max.
9
0
(Default value:
SC=00; SE=00; BR=07; PL=05 )
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
01 • Use UP until appears .
02 • Press MENU. The factory set time appears.
03 • Use UP and DW to change the value.
04 • Press MENU to save the new value.
The pedestrian mode allows the gate to be opened for the passage of
people, without it needing to open in its entirety.
In this function you can schedule the time you want the gate to open.
For pedestrian mode to work, it is necessary that the
minimum work is 1 second, and 0 disables the pedestrian.
(Default value 10 secondes)
99s0s
min. max.
TEMPO DE PAUSA E ATRASO DE PORTAS
Full closing pause time adjustment
This menu allows to set the total opening
pause time.
Pedestrian lock pause time adjustment
Allows to set the pause time at the pedestrian
opening.
(Default value 0) (Default value 0)
When the values are at zero, there is no automatic closing.
99s
min. max.
0s
99s
min. max.
0s
FORCE AND SENSIBILITY ADJUSTMENT
. PROGRAMMING "P"
PEDESTRIAN COURSE TIME
. PROGRAMMING "P" PAUSE TIME
. PROGRAMMING "P"

16A 16B
ENEN
01 • Use UP until appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
00 (off)
01 (active)
Enable or disable security
entry.
00 (opening photocells)
01 (closing photocells)
This menu can only be changed
when the LE menu is active.
Allows you to define whether
this security will act on the
opening or closing of the gate.
00 (the gate is reversed)
01 (gate to and resumes 5 sec
after security is disabled)
02 (gate reverses for 2 sec. and
stop)
It allows to define the
behavior that the gate will
have when this security is
activated.
(Default value 0) (Default value 1) (Default value 0)
Allows to program le security behavior LE (photocell 1).
01 • Use UP until appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
PAUSE TIME
PHOTOCELLS  PROGRAMMING
. PROGRAMMING "P"
. PROGRAMMING "P"
01 • Use UP until appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
00 (off)
01 (active)
Enable or disable
security entry.
00 (opening
photocells)
01 (closing photocells)
This menu can only be
changed when the LA
menu is active. Allows
you to define whether
this security will act on
the opening or closing
of the gate.
00 (the gate is
reversed)
01 (gate to and
resumes 5 sec after
security is disabled)
02 (gate reverses for 2
sec. and stop)
Allows to set the
behavior that the gate
will have
when this security is
activated.
00 (disables security
band)
01 (active security
band)
(Default value 0) (Default value 0) (Default value 1) (Default value 0)
Allows to program le security behavior LA (photocell 2).
This menu allows to set the operating logic of the automation
Automatic Mode
Whenever there is an order the
movement is reversed.
Step by step mode
1st impulse - OPEN
2nd impulse - STOP
3rd impulse - CLOSED
4th impulse - STOP
Stopping movement during closing
disables automatic closing.
Condominium Mode
Does not respond to orders
during opening and break time.
(Default value: SC=01; SE=01; BR=02; PL=02)
PHOTOCELLS  PROGRAMMING
. PROGRAMMING "P"
OPERATING LOGIC
. PROGRAMMING "P"

17A 17B
ENEN
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
Intermitente
(opening and closing)
During the opening/closing
movement of the gate, the fire-
fly will operate intermittently.
Opening - flashing 2s
Closing - flashing 1s
In the opening and closing
movement, the flashing light is
permanently on.
When it's still stays off.
Courtesy light
In the opening and closing
movement the firefly is
permanently connected. When
in pause time
remains connected.
When stopped or closed,
remains on for the time set
in E2.
Default value (00)
This menu allows to set the operation mode of the flashing light (LAMP).
Distance PGM OFF Distance PGM ON
This menu allows to enable or disable the programming of new commands without directly
accessing the central, using a previously stored command
(memorize commands page 11B).
Default value (00)
OPERATING LOGIC
FLASHING LIGHT
REMOTE PROGRAMMING
. PROGRAMMING "P"
. PROGRAMMING "P"
. PROGRAMMING "P"
Remote Programming Operation (PGM ON):
• Press the keys indicated in the image simultaneously for 10
seconds and the flashing light will flash (the 1st free position
appears in the display).
Each time you store 1 command, the control board will exit remote
programming. If you want to memorize more commands, you will
always have to repeat the process of pressing the command keys
simultaneously for 10 seconds for each new command.
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
00 (disables present man)
Whenever a order to ls input
and motorperforms a complete
manoeuvre.
Man present
01 (active present man)
The motor only works if you keep
the LS button pressed.
With the man present active the RF
commands do not
work.
00 (disables pushbutton mode)
01 (active pushbutton mode)
Allows you to define the way
Operation of the LB input
00 (disables input to
emergency stop device)
01 (input for
emergency stop)
02 (sensor input
twilight - outputs for LEDs that
run at night and
remain out of the day)
(Default value 00)(Default value
SC=00; SE=01; BR=00; PL=02)
LS LO
01
ACTIVE Full
closing Full opening
00
OFF
Pedestrian
opening
Full
opening
01 • Press MENU for 5 sec. until it appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
REMOTE PROGRAMMING
PRESENT MAN/PUSHBUTTON
. PROGRAMMING "P"
. PROGRAMMING "E"

18A 18B
ENEN
00 off
01 active
Enables or disables the soft start. With the soft start function activated, at each start of move-
ment the control unit will control the engine start, increasing the speed gradually in the first
second of operation.
(Default value: SC=01; SE=01; BR=01; PL=01)
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
Allows to adjust the courtesy light time. The courtesy light is activated the set time when the
gate is in the closed, open and standing position.
The E2 menu will only be available in the case of the
courtesy to be activated in the P8 menu option 2 (see page 16A).
(Default value 00)
SOFT START
COURTESY LIGHT TIME
. PROGRAMMING "E"
. PROGRAMMING "E"
01 • Use UP until appears .
02 • Press MENU. The factory set time appears.
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
00 function disabled
01 function activated after opening
02 function activated on opening
Allows you to activate the Follow me option. With this option activated, the control board, when
in the open or open position, gives a closing order of 5 sec. after the safety device detects the
passage of an object / user.
(Default value 00)
Opening stroke time
(minutes) Opening stroke time (secondes) Closing stroke time (minutes) Closing stroke time (secondes)
(Default value 0) (Default value 10) (Default value 0) (Default value 10)
Allows to adjust the working time for the opening and closing strokes at normal speed
01 • Use UP until appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
FOLLOW ME
COURSE TIME ADJUSTMENT
. PROGRAMMING "E"
. PROGRAMMING "E"

19A 19B
ENEN
00 (disables electronic brake)
01 (activates electronic brake)
Allows you to activate the electronic brake.
00 (active lock at opening 1 sec.)
01 (activates lock with polarity)
Allows you to select how the lock works.
(Default value 0) (Default value 0)
Allows to activate the electronic brake and change the behaviour of the LK output (lock)
This menu allows you to adjust the slowdown speed.
The higher the level, the faster the slowdown.
01 • Use UP until appears .
02 • Press MENU will appear . Use UP or DW to navigate the parameters.
03 • Press MENU to edit the chosen parameter value.
04 • The factory set time appears. Use UP and DW to change the value.
05 • Press MENU to save the new value.
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
BRAKE/LOCK/PUSH
DECELERATION SPEED
. PROGRAMMING "E"
. PROGRAMMING "E"
Setting of the slowing speed at the opening
Allows you to adjust the slowing speed in the engine
opening.
Setting of the slowing speed at the closing
Allows you to adjust the slowing speed in the engine
closing.
min. max.
9
0
(Valor de fábrica: SC=05; SE=05; BR=02; PL=05)
min. max.
9
0
(Valor de fábrica: SC=05; SE=05; BR=01; PL=05)
This menu allows you to view the number of maneuvers performed.
(complete maneuver means opening and closing).
Resetting the control board does not clear the maneuver count.
Example: 13456 maneuvers
01- Hundred thousand / 34- Thousands / 56- Dozens
01 • Press MENU for
10 secondes. 02 • E0 appears.
Press UP until
appears E7.
03 • Press MENU.
1º   2º 
display flashes display flashes
04 • The maneuvers count is displayed in the following order (example: 130 371)
05 • E8 appears.
3º dozens
2º thousands
1º hundred thousand
MANUEVERS COUNTER
. PROGRAMMING "E"

20 EN
Continuous light Flashing light
(Default value 00)
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
01 • Use UP until appears .
02 • Press MENU will appear .
03 • Press MENU to edit the value.
04 • Use UP and DW to change the value.
05 • Press MENU to save the new value.
RESET - RESET FACTORY VALUES
RGB OUTPUT
. PROGRAMMING "E"
. PROGRAMMING "E"
Only the maneuver counter will always have the data stored.