Motorline professional MCONNECT SHUTTER Use and care manual

PULL
v1.2
REV. 01/2022
MCONNECT
MCONNECT SHUTTER
EN
USER’S AND INSTALLER’S MANUAL

1A 1B
1B
4A
4B
4B
5A
5B
6A
6A
6A
6B
6B
ENEN
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed of
as other household waste at the end of its useful life. To avoid
possible harm to the environment or human health resulting
from the uncontrolled disposal of waste, separate these items
from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Home
users should contact the dealer where they purchased this
product or the National Environment Agency for details on
where and how they can take these items for environmentally
safe recycling. Business users should contact their vendor and
check the terms and conditions of the purchase agreement.
This product and its electronic accessories should not be
mixed with other commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
the product and observe all safety procedures in this manual.
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX ATTENTION:
CONNECTION TO WALL SWITCH OF 2 KEYS
MCONNECT SHUTTER
GRAPHIC DESCRIPTION
TECHNICAL SPECIFICATIONS
PRODUCT INSTALLATION
ADD MODULE IN IN THE APP
OPERATING SETTINGS
INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS
01. SAFETY INSTRUCTIONS
02. CONNECTIONS SCHEME
03. CONTROL BOARD
04. INSTALLATION
05. CONFIGURATION
06. TROUBLESHOOTING
REMOVE MODULE FROM THE APP
RESET

2EN
01. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•This manual is intended firstly for specialized technicians, and does
not invalidate the user’s responsibility to read the “User Norms”
section in order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical, sensorial or mental capacities are lower, or by persons
without any knowledge of the product, provided that these are
supervision and instructions given by persons with experienced in
terms of usage of the product in a safe manner and who understands
the risks and dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points to
ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•Thecentralmustbeinstalledonasafeplaceofanyfluid(rain,moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of

3EN
16 September 2009.
•Attach the permanent label for the manual release as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
01. SAFETY INSTRUCTIONS
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information

4A 4B
PULL
230V
ENEN
LEDs
• Flash in purple Pairing mode (It is waiting to be added)
• Red No network
• Flash in red Lost connection to the cloud
• Blues Successfully connected to the local network, but not yet connected
to the cloud
• Flash in blue Upgrading Firmware
• Green Connected to the cloud
MOTOR
COM Motor Output - Common
FCH Motor Output - Close
AB Motor Output - Open
PULL
Wall switch connection - Common
FCH Wall switch connection - Close (NA)
AB
Wall switch connection - Open (NA)
-AC
F230V line input (phase)
N230V line input (neutral)
GRAPHIC DESCRIPTION
The MCONNECT SHUTTER was developed to control roller shutters by distance or push button, using
the MCONNECT app and a module previously connected to the application. Its small size allows the
installation inside a junction boxes, behind electrical switches (push buttons).
Advantages of using MCONNECT:
• Easy installation and configuration;
• Possibility to control the lights in your home from anywhere;
• Reading the status of electric shutters, recognizing the opening/closing
state and/or its opening percentage;
• Recognizing the opening/closing state and/or its opening percentage;
• Possibility of configuring routines for the devices (example: open the
electric shutter at am and close at .am).
Motor
02. CONNECTIONS SCHEME
CONNECTION TO WALL SWITCH OF 2 KEYS MCONNECT SHUTTER
03. CONTROL BOARD

5A 5B
54
2
3
ENEN
TECHNICAL SPECIFICATIONS
03. CONTROL BOARD
• Power Supply 90-230 Vac 50-60Hz
• Maximum engine power 230Vac; 750W
• Output relay capacity 5A 250VAC 5A 30VDC
• Consumption 15mA @ 230AC
• Operating temperature -20C to 70C
• Module frequency 2.4 GHz
• Input 2 contact inputs without tension
• Output 2 relay outputs without tension
• Technology WIFI IEEE 802.11b/g/n , Bluetooth
• Wifi access 50m in open country
• Protection level IP44
• Construction material ABS
23mm
56mm
44mm
52mm
04. INSTALLATION
PRODUCT INSTALLATION
1 • Turn off the general lights of the house on the
electrical panel.
2 • Disassemble the switch plate and disconnect
all wires.
3 • Connect module wires to the installation
wires (see page A).
4 • Insert the MCONNECT SHUTTER module inside
the junction box.
5 • Replace the switch plate and tighten it
completely.
• The existence of a Wi-Fi network is required in the space where the device will be working;
• The device must be installed behind a normal switch, inside the junction box, passing all light control to
be performed by the device.

6A 6B
PULL
PULL
PULL
ENEN
05. CONFIGURATION05. CONFIGURATION
OPERATING SETTINGS
• SWITCH AND SENSOR MODE
Input AB acts as a pulse
switch (ignores Switch Mode),
controlling up and down.
The FCH input is used as a
sensor/closing contact.
• SENSORS MODE
Input AB is used as opening
sensor and FCH as sensor/closing
contact.
• SWITCHES MODE
Inputs are both used as
switches. FCH to close and
AB to open.
INPUTS MODE
REVERSE DIRECTION
This mode, when active, inverts the outputs to the motor. The opening exit starts to close and vice versa.
It is used when the installer makes the connections in reverse.
OPENING TIME
Used to indicate the time takes by the shutter to open/close, so that the opening control feedback is as
real as possible.
Sensor/Magnetic
Opening Contact
Sensor/Magnetic
Closure Contact Sensor/Magnetic Closure Contact
1 • Open MCONNECT app.
2 • Log in.
3 • On the home page press the "+" button at the top right.
4 • Press Add new MCONNECT.
5 • Accept all requested permissions.
6 • Turn on the power.
7 • Check that the module is in pairing mode (flashing purple).
Note • if it is not in pairing mode it is necessary to reset.
8 • Read the QR Code on the module box.
9 • If you prefer or don't have the QR Code, can change the button to Scan
nearby and select the module in the devices found.
10 • Enter the name and password of the Wifi network you are connected to.
11 • Wait for add process be complete.
ADD MODULE IN IN THE APP
1 • Press on the device you want to remove.
2 • Press on the icon with a gear symbol on the upper right side of the screen.
3 • Press Remove MCONNECT.
4 • Confirm.
REMOVE MODULE FROM THE APP
RESET
Reset button
When resetting, the device is no longer connected to the
account it is associated with in the application.
Press the reset button until the LED changes to pairing mode
(flashing purple), which will confirm successful operation.
SWITCH MODE
• PULSE
The shutter changes state when the pulse switch is
pressed.
• EDGE MODE
Changes the state (ON or OFF) when switch changes the
position.
Ex: If the wall switch is in the open position and the
shutter is closed, turning the switch to the closed
position will open the shutter.

7EN
INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS
06. TROUBLESHOOTING
PROBLEM SOLUTION
The LED reader does not light up Check that the power is connected correctly.
The module is not in pairing mode
(LED flashing purple) and I haven't
configured it yet
Press the Reset button located on the back of the modu-
le, until it switches to pairing mode.
The module has the red LED
Make sure the network you configured the module on is
available.
Check if you have coverage of the network to which the
module is connected.
Check if the network you have configured the module has
Internet access.
The module has the blue LED Check if the network you configure the module has Inter-
net accesst.
The output does not change state Check that the connections are correct.
The switch does not change the state
output Make sure the connections are correct. Check the App if the switch mode is in the correct mode.