Motorline professional MC75 Use and care manual

v1.3
REV. 10/2019
EN
USER’S AND INSTALLER’S MANUAL
MC75

1B
4
5A
5A
5B
6A
6A
6B
6B
6B
7A
7A
7A
7B
7B
7B
7B
8A
9
9
8A
8B
8B
1A 1B
ENEN
00. CONTENT 01. SAFETY NOTICES
INDEX STANDARDS TO FOLLOW
STANDARDS TO FOLLOW
KEY CONTROLLERS
LEDS
KEY CONTROLLERS
COMMAND FOR EXTERNAL LAMP CONTROL
PROGRAMMING OF REMOTE CONTROL
PROGRAMMING EXTERNAL LAMP COMMANDS REMOTELY
DELETE ALL THE CONTROLLERS
CONNECTING COMPONENTS TO THE CONTROL BOARD
THECNICAL CHARACTERISTICS
INFORMATION LEDS
CONNECTION SYSTEM
. SAFETY NOTICES
. THE CONTROL BOARD
. CONNECTIONS SCHEME
. MAIN MENU
MOTORS WORKING TIME
EXTENDED MENU 
INSTRUCTIONS FOR FINAL CONSUMERS
INSTRUCTIONS FOR SPECIALIZED INSTALLERS
MAN PRESENT FUNCTION
EXTENDED MENU 
. EXTENDED MENU
. TROUBLESHOOTING
USE OF PHOTOCELLS
SETTING THE PAUSE TIME
TOTAL RESET
EXTENDED MENU 
EXTENDED MENU 
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where they
purchased this product or the National Environment Agency
for details on where and how they can take these items
for environmentally safe recycling. Business users should
contact their vendor and check the terms and conditions
of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.

2A 2B
ENEN
01. SAFETY NOTICES 01. SAFETY NOTICES
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•Thismanual is intendedfirstlyforspecialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical,sensorialormentalcapacitiesarelower,orbypersonswithout
any knowledge of the product, provided that these are supervision
and instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The centralmust be installed on asafe placeof anyfluid (rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
•Attach the permanent label for the manual release as close as possible

3A 3B
ENEN
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
01. SAFETY NOTICES 01. SAFETY NOTICES

4A
SEL SET
PHOTO
P.MAN
TIME.M
CMD.L
CMD.S
CMD
TIME.P
Op
LAb Fe V + Op Cl Le
Com
N
Cl Ce
1 2 3 4 5 6 7 8 9 10 11 12 13
230v
110v
DV NC12/24V DV 12/24VCOM
MOTOR
~ ~ ~ ~
Op
230~
LAb Fe
V + Op Cl Le
Com
N
230~
Cl Ce
1 2 3 4 5 6 7
8 9 10 11 12 13
i
Op
230~
LAb Fe
V + Op Cl Le
Com
N
230~
Cl Ce
1 2 3 4 5 6
78 9 10 11 12 13
i
TUB | Rolling
4EN
02. CONNECTIONS SCHEME
CONNECTING COMPONENTS TO THE CONTROL BOARD
Shunt
 Button Controler
- Step by Step Operation
You must put a bridge
(shunt) between Op and Cl,
connecting the control board
between the OP and the COM
 Buttons Controler
-  button for opening and
another one for closing
Photocells set
Antenna
Lamp

SEL SET
PHOTO
P.MAN
TIME.M
CMD.L
CMD.S
CMD
TIME.P
Op
230~
LAb Fe V + Op Cl Le
Com
N
230~
Cl Le
1 2 3 4 5 6 7 8 9 10 11 12 13
SEL SET
PHOTO
P.MAN
TIME.M
CMD.L
CMD.S
CMD
TIME.P
Op
230~
LAb Fe V + Op Cl Le
Com
N
230~
Cl Le
1 2 3 4 5 6 7 8 9 10 11 12 13
5A 5B
ENEN
The MC is a control board developed specifically for rolling motors (TUB and ROLLING range), which
allows the programming of working time and the time for self-closing.
It has the ability to detect limit switch devices and when the motor is locked, and as such, the working
time ends as soon as the curtain or grid reaches a limit switch and when it detects that the motor is
locked (in effort).
V V
• Power Supply Vac /Hz Vac /Hz
• Motor output power W máx W máx
• OP Transmitters  Bits ou Rolling Code
• Maximum memory capacity  Codes
• Working temperature -°C  °C
• Built-in radio receiver , Mhz
• Auxiliary accessory output Vdc/mA
• External lamp output W W
• Motor output fuse Øxmm Ah Øxmm Ah
Low voltage fuse for accessories output Øxmm mA
03. THE CONTROL BOARD 03. THE CONTROL BOARD
THECNICAL CHARACTERISTICS
LED description
OP Opening order Receiving sinal No activity signal
Cl Closing order Receiving sinal No activity signal
Le Indication of the Cell Circuit Button Detected cells Cells not detected
CONNECTORS
INFORMATION LEDS
1• 230V/110V Power Supply - Phase (L) Power supply connection
2• 230V/110V Power Supply – Neutral (N)
3• External Lamp output - Phase Connection for external lamp with maximum output
duration of  min.
4• External Lamp output - Neutral
5• Motor output – Opening (Ab) Connection of the opening and closing phases of the
motor.
If the direction of the motor is contrary to the intended
direction, simply replace the two wires to reverse the
direction.
6• Motor output - Neutral (COM)
7• Motor output – Closing (Fe)
8• Vdc Ma Auxiliary output (V) Device power output
9• Common (COM)
10 • NO input for control board - Closing (Op) Circuit for connection of controller:
Two button controller: Opening and closing control on
each button.
One button controller: Operates in Step-by-step mode
(open-close-close-stops -...) always with the same button.
To do this, you must put a shunt between Op and Cl, by
connecting the controller between Op and COM.
11 • Common (COM)
12 • NO input for control board - Closing (Cl)
13 • NC input for Photocells (Le)
[Complete circuit with COM (9 or 11)]
This circuit allows the connection of all types of safety
photocells.
This device only intervenes in closing and pause opera-
tions, as follows:
- In closing, stops and starts the complete opening of the
operator
- In pause time, it prevents the operator from starting the
closing by holding it open.

SEL SET
PHOTO
P.MAN
TIME.M
CMD.L
CMD.S
CMD
TIME.P
Op
230~
LAb Fe V + Op Cl Le
Com
N
230~
Cl Le
1 2 3 4 5 6 7 8 9 10 11 12 13
6A 6B
ENEN
04. MAIN MENU 04. MAIN MENU
2KEY CONTROLLERS
Functionality - This function allows you to store a 2-key control via the control board.
Storing a 2-key controllers (normal operation):
 • Press the SEL button as many times as necessary until the CMD LED starts blinking.
 • Press the control closing key for  second. The CMD LED flashes at twice the initial speed,
signaling the key recording.
 • Press the control opening key for  second. The CMD LED stops blinking, signaling the
key recording, and the CMD.L LED flashes.
Wait for  seconds, the control board exits of programming mode and all LEDs stop blinking.
Controller(s) programmed No programmed controllers
Functionality - This function allows you to store a 1-key control via the control board.
Storing a 1-key remote control (Step by Step operation):
 • Press the SEL button as many times as necessary until the CMD LED starts blinking.
 • Press the control closing key for  second. The CMD LED flashes at twice the initial speed,
signaling the key recording.
 • The command is stored.
Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.
LEDs Main menu: The control board has a set of LEDs that allows to identify the status of
the different functions.
1KEY CONTROLLERSLEDs
Controller(s) programmed No programmed controllers
COMMAND FOR EXTERNAL LAMP CONTROL
PROGRAMMING OF REMOTE CONTROLS
Functionality - This function allows you to store a command to control the external lamp throu-
gh the control board.
Storing a command to control the external lamp:
 • Press the SEL button as many times as necessary until the CMD.L LED starts blinking.
 • Press the control button for lamp output control for  second.
 • The controller is stored.
Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.
Controller(s) programmed No programmed controllers
Functionality - This function allows you to program new controllers via an already configured
controller.
Programming remote controls for:
 • With the rolling grilles fully open/closed, press the open/close button of a controller
already programmed for a time superior to  seconds. When the lamp blinks twice, the
control board has entered on programming mode remotely.
 • Push the closing button of the new control for  second. The lamp blinks once.
 • Press the button for the opening of the new control. The lamp blinks twice and the
control is programmed.
Controller(s) programmed No programmed controllers
LED Description
TIME P Pause time Programmed Not Programmed
PHOTO Enable Cells Active Disabled
P. MAN Man Present Active Disabled
TIME. M Working time Active Disabled
CMD. L. Lamp controler Programmed controller(s) No Program. controllers
CMD. S. Not applicable Not applicable Not applicable
CMD. Controller Programmed controller(s) No Program. controllers

7A 7B
ENEN
04. MAIN MENU 04. MAIN MENU
Functionality - This function allows you to set the opening and closing time of the motor.
 • Close the rolling grilles manually.
 • Press the SET button continuously for the time required for the opening operation.
 • Press the SET button continuously for the time required for the opening operation.
When you reach the end of the aperture, release the SET key to end programming. If you have
activated the "Detection of Limit Switch" option, this programming will end automatically
when the control unit detects the limit switch.
Wait for  seconds, the control board exits the programming mode and all LEDs stop
blinking.
Functionality - This function allows you to activate the Present Man function. When enabled,
the operator only closes while holding down the close button .
 • Press the SEL button as many times as necessary until the P.MAN LED blinks.
 • Press the SET button to enable/disable the option.
Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.
Functionality - This function allows you to activate/deactivate the use of the Photocells, to
reverse or prevent the opening of the automation when the signal is interrupted .
 • Press the SEL button as many times as necessary until the LED PHOTO blinks.
 • Press the SET button to enable/disable the option.
Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.
PROGRAMMING EXTERNAL LAMP COMMANDS REMOTELY
MOTORS WORKING TIME
MAN PRESENT FUNCTION
TOTAL RESET
SETTING THE PAUSE TIME
Function on
Function on
Function off
Function off
USE OF PHOTOCELLS
If you do not connect photocells to the control board, you must deactivate
this function.
Functionality - This function allows you to set the time the automation waits after opening until
the automatic closing is started.
 • Press the SEL button as many times as necessary until the TIME.P LED starts blinking.
 • Press the SET button to start counting time (the LED flashes at twice the initial speed), and
press again the SET button to end the pause time count.
Functionality - This function allows you to restore all the factory settings and all the stored
commands will be erased .
 • Press the SEL and SET buttons at the same time for  seconds. The LEDs turn on and off,
signaling that the operation has been done.
Functionality - This function allows you to store a command to control the external lamp via an
already configured control.
Remote Control programming for external lamp control:
 • Press the button of the lamp of a controller already programmed for a time superior
to  secunds. When the lamp blinks twice, it has entered on programming mode remotely.
 • Press the lamp button of the new controller.
The lamp blinks twice and the control is programmed.
Controller(s) programmed No programmed controllers
Functionality - This function allows you to delete all commands added to the control board.
 • Press the SEL button as many times as necessary until the CMD LED blinks.
 • Press the SET button once and the CMD LED goes off signaling the elimination of all the
controllers.
DELETE ALL THE CONTROLLERS
Controller(s) programmed No programmed controllers

8A 8B
ENEN
05. EXTENDED MENU 05. EXTENDED MENU
EXTENDED MENU 2 - Programming of remote controls
EXTENDED MENU 3 - Motor Type Connected
Functionality - This menu allows you to activate or deactivate the possibility of programming new commands
through an already configured command.
The control board is supplied with this PGN function enabled
01 • Access Extended Menu 1 (see the previous menu items).
02 • Within the Extended Menu 1, press the SET button for more than 5 seconds. The TIME.M and CMD.L LEDs
flash simultaneously.
03 • Press the SEL button to turn on/off the CMD LED by choosing the desired option!
04 • Press the SET button to save the selected option.
The control panel will automatically exit programming mode.
Functionality - This menu allows you to choose the type of motor connected to the control board for the
functions of effort reversal (motor locked).
The control board is supplied with 17RPM Motor mode enabled.
To access the Extended Menu 3 options follow the steps:
01 • Access Extended Menu 2 (see the previous menu items).
02 • Within the Extended Menu 2, press the SET button for more than 5 seconds. The TIME.M and CMD.L LEDs
flash alternately quickly.
03 • Press the SEL button to turn on/off the CMD LED by choosing the desired option!
04 • Press the SET button to save the selected option.
The control board will automatically exit programming mode.
EXTENDED MENU 2
LED LED off LED on
• CMD PGM at distance = ON PGM at distance = OFF
• CMD.L Flashing ON/OFF
• TIME.M Flashing OFF/ON
EXTENDED MENU 3
LED LED off LED on
• CMD 12RPM Motor 17RPM Motor
• CMD.L Flashing ON/OFF
• TIME.M Flashing OFF/ON
EXTENDED MENU 1 - LAMP/CORT - Output control for Lamp
Functionality - This menu allows you to set the type of external lamp operation. The control board is su-
pplied by default with the lamp control via the control.
To access the Extended Menu 1 options follow the steps:
01 • Press the SET button for more than 5 seconds. The TIME.M and CMD.L LEDs flash alternately.
02 • Press the SEL button to pass through the various operating modes.
03 • Press the SET button to save the selected option.
The control panel will automatically exit programming mode.
EXTENDED MENU 1
Operation LED CMD LED CMD.S
• Control by remote control Deleted Deleted
• Lamp lights on opening and
closing On Deleted
• Lamp lights on at opening, clo-
sing, and pause time (when active) Deleted On
• Lamp lights in the opening, in
the closing, in the pause time and
stays on for three minutes after
closing
On On
• CMD.L Flashing ON/OFF
• TIME.M Flashing OFF/ON
EXTENDED MENU 4
LED LED off LED on
• CMD Disable detection Enable detection
• PHOTO Flashing ON/OFF
• TIME.P Flashing ON/OFF
Functionality - This menu allows you to set the sensitivity levels for the locked motor detection. The
control panel is supplied at the factory with level 0 (detection disabled), and this value can be adjusted,
ranging from 1 to 5 (1 more sensitive and 5 less sensitive).
To access the Extension Menu 4 options, follow the instructions below:
01 • Access Extension Menu 3 (see instructions in the previous menu).
02 • Within the Extended Menu 3, press the SET button for more than 5 seconds. The LEDTIME.P and PHOTO
will flash rapidly alternately.
03 • Press the SEL button as many times as necessary to change the values. The LEDs will light sequentially.
EXTENDED MENU 4 - Motor detection locked
Level LEDs
1CMD
2CMD CMD.S
3CMD CMD.S CMD.L
4CMD CMD.S CMD.L TIME.M
5CMD CMD.S CMD.L TIME.M P.MAN

9A
9EN
. TROUBLESHOOTING
INSTRUCTIONS FOR FINAL CONSUMERS INSTRUCTIONS FOR SPECIALIZED INSTALLERS
Anomaly Procedure Behavior Procedure II Discovering the origin of the problem
• Motor
doesn’t work • Make sure you have 110/230V power
supply connected to
automation and if it
is working properly.
• Still not working • Consult a qualified
MOTORLINE technician. 1 • Open control board and check if it has 110/230V power supply; 2 • Check the control board input fuses;
3 • Disconnect the motor from control board and test them by connecting directly to 230Vdc power supply in order to find out if they have problems.
4 • If the motor works, the problem is on the control board. Pull it out and send it to the MOTORLINE technical services for diagnosis;
5 • If the motor doesn’t work, remove them from installation site and send to the MOTORLINE technical services for diagnosis.
• Motor
doesn’t move
but makes
noise
• Unlock motor and
move the rolling
grilles by hand to
check for mechanical
problems on the
movement.
• Encountered
problems? • Consult an experienced rolling grilles expert.  • Check all motion axis and associated motion systems related with the rolling grilles and the automatism (bolts, hinges, etc.) to find out what is the problem.
• The rolling grilles
moves easily? • Consult a qualified MOTORLINE technician.  • If the motor works, the problem is on the control board. Pull it out and send it to the technical services for diagnosis;  • If the motor doesn’t work, remove them from installation site and send to the technical services for diagnosis.
• Motor
opens, but
doesn’t close
• Unlock motor and
move the rolling
grilles by hand to
closed position. Lock
motor again and turn
off power supply for
5 seconds. Reconnect
it and send order to
open rolling grilles
using controller.
• Rolling grilles
opened but didn’t
close again.
1 • Check if there is any
obstacle in front of the
photocells;
 • Check if any of the control
devices (key selector, push
button, video intercom,
etc.) of the rolling grilles
are jammed and sending
permanent signal to control
unit;
 • Consult a qualified
MOTORLINE technician.
All control boards MOTORLINE have LEDs that easily allow to conclude which devices are with anomalies. All safety devices LEDs (DS) in normal
situations remain On. All "START" circuits LEDs in normal situations remain Off.
If LEDs devices are not all On, there is some security systems malfunction (photocells, safety edges). If "START" circuits LEDs are turn On, there is
a control device sending permanent signal.
A) SECURITY SYSTEMS:
 • Close the cell circuit with shunt or disable the PHOTO function.
 • Check if the system is functional.
 • Replace this device with a functional one, and verify if the automation functions correctly with all other devices. If you find any other faults,
follow the same steps until you discover all the problems.
B) START SYSTEMS:
 • Disconnect all wires from START (PUL and PED) connector.
 • If the LED turned Off, try reconnecting one device at a time until you find the defective device.
NOTE:
In case procedures described in sections A) and B) don’t result, remove control board and send to the technical services for diagnosis.
• Motor
doesn’t make
complete
route
Unlock motor and
move rolling grilles
by hand to check
for mechanical
problems on the
rolling grilles.
• Encountered
problems? • Consult an experienced rolling grilles expert.  • Check all motion axis and associated motion systems related with the rolling grilles and the automatism (bolts, hinges, etc.) to find out what is the problem.
• The rolling grilles
moves easily? • Consult a qualified MOTORLINE technician.  • Make sure that the limit switches are correctly tuned.  • Are properly tuned.
 • Start the programming again with the rolling grilles fully closed.
. • Deactivate the Extension Menu  (Motor detection locked).
 • If the motor doesn’t work, remove them from installation site and send to the technical services for diagnosis.
 • If motor work well and move rolling grilles at full force during the entire course, the problem is from controller.