Motorola IXPN4028 User manual

Radio Communications Supply &
Installation Specialist
Website
www.radiotronics.co.uk
Email
[email protected]
Telephone Numbers
0345 0 955 955
02087 190 180
User Guide

CLP Series
Single Unit Charger (SUC)
P/N IXPN4028
en de-DE fr-FRes-ES it-IT
pt-PT
nl-NLda-DK
sv-SEfi-FInb-NO tr-TRpl-PL ru-RU uk-UA
68012002078.book Page 1 Monday, October 10, 2016 7:01 PM

68012002078.book Page 2 Monday, October 10, 2016 7:01 PM

1
English
IMPORTANT SAFETY INSTRUCTIONS
This document contains important safety and operating instructions. Please read these
instructions carefully and save them for future reference.
Before using the battery charger, read all the instructions and cautionary markings on (1) the
charger, (2) the battery and (3) on the radio using the battery.
1. To reduce the risk of injury, charge only the rechargeable Motorola Solutions authorised
batteries listed in this document. Other batteries may explode, causing personal injury and
damage.
2. Use of accessories not recommended by Motorola Solutions may result in risk of fire, electric
shock or injury.
3. To reduce the risk of damage to the electric plug and cord, pull by the plug rather than the
cord when disconnecting the charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in risk of fire and electric shock. If an extension cord must be
used, make sure that the cord size is 18 AWG for lengths up to 6.5 feet (2.0 m) and 16 AWG
for lengths up to 9.8 feet (3.0 m).
5. To reduce the risk of fire, electric shock or injury, do not operate the charger if it has been
broken or damaged in any way. Take it to a qualified Motorola Solutions service
representative.
6. Do not disassemble the charger; it is not repairable and replacement parts are not available.
Disassembly of the charger may result in risk of electrical shock or fire.
7. To reduce the risk of electric shock, unplug the transformer from the AC outlet before
attempting any maintenance or cleaning.
032374o
WARNING
68012002078.book Page 1 Monday, October 10, 2016 7:01 PM

2
English
OPERATIONAL SAFETY GUIDELINES
• Turn the radio OFF when charging battery.
• The charger is not suitable for outdoor use. Use only in dry locations/conditions.
• Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on
the product).
• Disconnect charger from line voltage by removing main plug.
• The outlet to which this equipment is connected should be nearby and easily accessible.
•Maximum ambient temperature around the power supply equipment must not exceed 40 °C (104 °F).
• Make sure that the cord is located where it cannot be stepped on, tripped over or subjected to water,
damage or stress.
MOTOROLA SOLUTIONS AUTHORISED BATTERIES
MOTOROLA SOLUTIONS AUTHORISED POWER SUPPLIES
Kit No. Description
HKNN4013_ CLP Series High Capacity Li -Ion Battery
HKNN4014_ CLP Series Standard Li -Ion Battery
Kit No. Description
PS000042A12 CLP Series EU Power Supply Adaptor
PS000042A13 CLP Series UK Power Supply Adaptor
NNTN7880_ CLP Series SUC Tray
68012002078.book Page 2 Monday, October 10, 2016 7:01 PM

3
English
Note: When charging a battery attached to a radio, turn the radio OFF to ensure a full charge.
The radio fits in the charger when placed face down in the tray.
Charging with the Drop-in Tray Single Unit Charger (SUC)
1. Place the drop-in tray charger on a flat surface.
2. Insert the connector of the power supply into the Micro USB port on the front of the drop-in
tray charger.
3. Connect the correct power supply to a proper AC outlet.
4. Insert the radio into the tray, making sure the radio is facing down and the charging contacts on
the charger are aligned with the contacts on the radio.
Kit # P/N IXPN4028_
68012002078.book Page 3 Monday, October 10, 2016 7:01 PM

4
English
Cloning Radios using the Single Unit Charger (SUC)
1. Unplug any cables (power supply or USB cables) from the Single Unit Chargers.
2. Plug one side of the cloning cable micro connector to one Single Unit Charger. Plug the other
end to the second Single Unit Charger.
Note: During the cloning process no power is being applied to the Single Unit Charger. The batteries are not being
charged. A data communication is being established between the two radios.
3. Turn ON the “Target Radio” and place it facing down into one of the Single Unit Chargers.
4. On the “Source Radio”, power the radio following the sequence below: • Press and hold the
Push-to-Talk (PTT) and the “-”. Button simultaneously while turning the radio ON until you hear
the Cloning Tone and Double Blinking Yellow on the Smart Status Glow.
5. Place the “Source Radio” facing down in its Single Unit Charger with an Audio accessory, then
press and release Menu Button to start the cloning process.
6. After cloning is completed, the “Source Radio” sounds either a “pass” tone (cloning was
successful) or a “fail” tone (cloning process has failed). The pass tone sounds like a good key
“chirp” whereas the “fail” tone sounds similar to a “bonk” tone. (A tone is heard in no more than
5 seconds.)
Cloning Cable HKKN4026_
(Not included)
68012002078.book Page 4 Monday, October 10, 2016 7:01 PM

5
English
Once you have completed the cloning process, you should turn the radios “OFF” and “ON” to bring
them to normal user mode (exit “clone” mode).
Charging Status LEDs
On the SUC, the radio charging pocket has an LED indicator. The LED indicators are grouped into
pairs to show which charging pockets are paired. The LED is red when the battery is charging, then
it turns to green once the battery is fully charged.
ESTIMATED CHARGING TIME
CHARGER LED INDICATOR
Charger Type Standard
Li-Ion
High Capacity Li-Ion
Single Unit
Charger
4 Hours 5.5 Hours
Status LED Status Comments
Charging Steady Red
Indication The Charger is currently
charging.
68012002078.book Page 5 Monday, October 10, 2016 7:01 PM

6
English
RADIO LED INDICATOR
Charge
Complete
Steady Green
Indication Battery is fully charged.
Battery
Fault
Blinking Red Battery was faulty when
inserted. Re-seating the
battery pack can probably
correct the issue.
Status LED Status Comments
Cloning Blinking
Yellow Cloning in progress.
Status LED Status Comments
68012002078.book Page 6 Monday, October 10, 2016 7:01 PM

7
English
Limited Warranty for Motorola Solutions Personal Communications Products Purchased
I. What Does This Warranty Cover?
• Products. Defects in materials and workmanship in wireless cellular telephones, pagers and/or
two-way radios and certain accessories that are sold with them, such as the battery, battery charger
and holster manufactured and/or sold by Motorola Solutions (Products).
• Batteries. Defects in materials and workmanship in batteries that are manufactured by Motorola
Solutions and/or sold with Products are covered by this warranty only if the fully-charged capacity
falls below 80% of rated capacity or they leak.
II. How Long Is The Period Of Coverage?
From the date the Products are purchased by the first end-user:
• Products. The warranty is for one year.
• Software. The warranty is for 90 days.
• Repairs/Replacements. The warranty is for the balance of the original warranty or for 90 days from
the date you receive it, whichever is longer.
III. Who Is Covered?
This warranty extends to the first end-user purchaser only.
IV. What Will We Do To Correct Warranty Problems?
At no charge to you, we have the option to repair or replace the Products or software that do
not conform to the warranty or to refund the Products’ purchase price. We may use functionally
equivalent reconditioned, refurbished, pre-owned or new Products or parts. No software updates
are provided.
68012002078.book Page 7 Monday, October 10, 2016 7:01 PM