Motorola M68EML08EY User manual

EML08EYUM/D
Version 1.0
May 2, 2002
User’s Manual
© Motorola, Inc., 2002
M68EML08EY
Emulation Module
User’s Manual

M68EML08EY Emulation Module - Version 1.0 User’s Manual
2MOTOROLA
Important Notice to Users
While every effort has been made to ensure the accuracy of all information in
this document, Motorola assumes no liability to any party for any loss or
damage caused by errors or omissions or by statements of any kind in this
document, its updates, supplements, or special editions, whether such errors are
omissions or statements resulting fromnegligence, accident, or any other cause.
Motorola further assumes no liability arising out of the application or use of any
information, product, or system described herein: nor any liability for incidental
or consequential damages arising from the use of this document. Motorola
disclaims all warranties regarding the information contained herein, whether
expressed, implied, or statutory, including implied warranties of
merchantability or fitness for a particular purpose. Motorola makes no
representation that the interconnection of products in the manner described
herein will not infringe on existing or future patent rights, nor do the
descriptions contained herein imply the granting or license to make, use or sell
equipment constructed in accordance with this description.
Trademarks
This document includes these trademarks:
Motorola and the Motorola logo are registered trademarks
of Motorola, Inc.
Windows is a registered trademark of Microsoft Corporation in the U.S.
and other countries.
Intel is a registered trademark of Intel Corporation.
Motorola, Inc., is an Equal Opportunity / Affirmative Action Employer.
For an electronic copy of this book, visit Motorola’s web site at http://e-www.motorola.com/
© Motorola, Inc., 2002; All Rights Reserved

User’s Manual M68EML08EY Emulation Module - Version 1.0
MOTOROLA Table of Contents 1
User’s Manual —M68EML08EY Emulation Module
Table of Contents
M68EML08EY Quick Start Guide
1 - Set jumpers W4 and W2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 - Install the emulation module into your development system . . . . . 7
3 - Connect the emulation module to your target system . . . . . . . . . . . 8
4 - Install the development software. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 - Copy personality files to your computer . . . . . . . . . . . . . . . . . . . . . 8
6 - Connect MMDS or MMEVS to your computer and apply power . 9
Section 1. General Information
1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2 Development Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.1 Motorola Modular Development System (MMDS0508). . . . . . . . 11
1.2.2 Motorola Modular Evaluation System (MMEVS0508). . . . . . . . . 12
1.3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.4 EM Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.6 Target Cable Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Section 2. Preparation and Operation
2.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2 Configuring Board Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.4 Remaining System Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

M68EML08EY Emulation Module - Version 1.0 User’s Manual
2 Table of Contents MOTOROLA
Table of Contents
Section 3. Support Information
3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 Target Connectors J2 and J3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Logic Analyzer Connectors J1 and J5 . . . . . . . . . . . . . . . . . . . . . . . . 24
3.4 Inverted Clock Connector J4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.5 Analog-to-Digital Converter Reference Voltage Connector E2. . . . . 26
3.6 Board Factory Test Connector J6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7 Optional crystal circuit using Y1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.8 Clock oscillator Y2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.9 EM Board Socket Connectors P1 and P2 . . . . . . . . . . . . . . . . . . . . . . 27

User’s Manual M68EML08EY Emulation Module - Version 1.0
MOTOROLA List of Figures 3
User’s Manual —M68EML08EY Emulation Module
List of Figures
1-1 M68EML08EY Emulator Module. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1-2 Target Cable Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3-1 Target Connector (J2) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . 21
3-2 Target Connector (J3) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . 23
3-3 Logic Analyzer Connector J1 Pin Assignments . . . . . . . . . . . . . . . . 24
3-4 Logic Analyzer Connector J5 Pin Assignments . . . . . . . . . . . . . . . . 25
3-5 Connector J4 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3-6 Connector E2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3-7 EM Connector P1 Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . 28
3-8 EM Connector P2 Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . 30

M68EML08EY Emulation Module - Version 1.0 User’s Manual
4 List of Figures MOTOROLA
List of Figures

User’s Manual M68EML08EY Emulation Module - Version 1.0
MOTOROLA List of Tables 5
User’s Manual —M68EML08EY Emulation Module
List of Tables
1-1 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1-2 EML08EY Target Cable and Head Assemblies . . . . . . . . . . . . . . . . 15
2-1 Configuration Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3-1 Target Connector (J2) Signal Descriptions . . . . . . . . . . . . . . . . . . . . 22
3-2 Target Connector (J3) Signal Descriptions . . . . . . . . . . . . . . . . . . . . 23
3-3 Logic Analyzer Connector J1 Signal Descriptions . . . . . . . . . . . . . . 24
3-4 Logic Analyzer Connector J5 Signal Descriptions . . . . . . . . . . . . . . 25
3-5 Connector J4 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3-6 Connector E2 Signal Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3-7 EM Connector P1 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . 29
3-8 EM Connector P2 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . 31

M68EML08EY Emulation Module - Version 1.0 User’s Manual
6 List of Tables MOTOROLA
List of Tables

User’s Manual M68EML08EY Emulation Module - Version 1.0
MOTOROLA M68EML08EY Quick Start Guide 7
User’s Manual —M68EML08EY Emulation Module
M68EML08EY Quick Start Guide
Make sure that power is disconnected from your M68EML08EY Emulator
Module and from your target system. Then follow these quick-start steps to
make your M68EML08EY ready for use as quickly as possible.
1 - Set jumpers W4 and W2
Jumper header W4 specifies the clock source for the MCU when you enable its
external clock.
•Place the jumper between pins 3 and 4 (factory default) to specify the
debugger-controlled oscillator from the platform board or place the
jumperbetweenpins1and2 tospecify4.9152-MHz oscillatorY2, which
can be replaced with an oscillator of a different value.
Jumperheader W2 specifies the voltagesupplied tothe emulationmoduleMCU
and to signals driven to the target.
•Place the jumper between pins 1 and 2 (factory default) to specify fixed
5.0 volts DC or place the jumper between pins 3 and 4 to specify fixed
3.0 volts DC.
2 - Install the emulation module into your development system
To use the M68EML08EY in an MMDS0508 Motorola Modular Development
System (MMDS) or MMEVS0508 Motorola Modular Evaluation System
(MMEVS):
•Remove the access panel of the MMDS station-module enclosure.
•Insert the M68EML08EY through the access-panel opening.

M68EML08EY Emulation Module - Version 1.0 User’s Manual
8 M68EML08EY Quick Start Guide MOTOROLA
M68EML08EY Quick Start Guide
•Fit together M68EML08EY connectors P1 and P2 (on the bottom of the
board) to connectors P11 and P12, respectively, of the MMDS or
MMEVS (P6 and P7 on some MMEVS boards) control board and snap
the corners of the M68EML08EY onto the plastic standoffs.
3 - Connect the emulation module to your target system
Use the supplied target flex cable, appropriate target head adapter, and surface
mount adapter. Plug the appropriate end of the flex cable plugs into
M68EML08EY connectors J2 and J3.
•If the M68EML08EY is in an MMDS station module, run the flex cable
through the slit in the station-module enclosure, then replace the access
panel.
•Plug the other end of the flex cable into the target head. Solder the
appropriate surface mount adapter to your target if necessary. Then plug
the target head into the surface mount adapter on your target system.
4 - Install the development software
5 - Copy personality files to your computer
The factory ships M68EML08EY MCU personality files on the documentation
CD-ROM.
•If you’re using the CodeWarrior IDE, find the installation directory and
copy the personality files named 00C31Vxx.mem and 00C32Vxx.mem
from the documentation CD-ROMto the ...\prog\reg subdirectory
of the CodeWarrior IDE main directory.
•If you’re using the P&E debugger, copy these files to the installation
directory that contains MMDS08.EXE or MMEVS08.EXE and rename
themfrom 00C31Vxx.mem and 00C32Vxx.mem to 00431Vxx.mem and
00432Vxx.mem respectively.