Motorola BOOM2 User manual

EN
MOTOROLA BOOM2
MOTOROLA BOOM2+

1
EN
AT A GLANCE
the important bits, quick and easy
Volume Up
Button
Charge
(Micro USB)
Call Button
Press to
answer/
end call.
Boom
open - on
close - off
Microphone
Volume Down Button
Charging Status Light:
Green – battery full
Yellow – around 50% charged
Red – battery low

EN
2
Wear
Ear Hook
Earpiece

3
EN
CHARGE IT
let’s get you up and running
To charge your headset, plug the USB cable into the
headset's micro USB port and connect to USB power
source.
Note: Fully charge the headset before you use it.
Tip: To save battery power, turn off the headset when
you’re not using it.
Caution: Your battery is designed to last the life of your
device. It should only be removed by a recycling
facility. Any attempt to remove or replace your battery
will damage the device, void your warranty, and could
cause injury.

CONNECT & GO
let’s get you connected
EN
4
EASYPAIRTM METHOD
Turn on Bluetooth on your device.
Turn on your headset and follow the voice
prompts.
Go to the Bluetooth menu on your device
to pair & connect with the headset. Enter
passcode 0000 if prompted.
When the device and headset connect,
you’ll hear “pairing complete”.

5
EN
COMFORT
what feels best on you
Choose your most comfortable t: on-ear hook, or ear
tip with no hook.
EAR HOOK
On-Ear Right Ear Left Ear
Rotate & turn ear hook for
right or left use
Wear

EAR TIP (NO HOOK)
Remove ear hook
Wear
Attach ear tip
EN
6

7
EN
BASICS
standard features, advanced quality
CALLS
To…
answer a call
reject a call
make a voice dial
call
redial last call
mute or unmute a
call
Press the Call button.
Press and hold the Volume Up or
Volume Down button until you
hear a tone.
Press the Call button to activate
voice recognition.
(phone dependent)
Press and hold the Call button
until you hear a tone.
Press and hold the Volume Up
and Volume Down buttons
together until you hear “mute
on” or “mute off”.

To…
end a call
change call volume
answer a second
incoming call
reject a second call
Press the Call button
Press the Volume Up or Volume
Down button. To quickly change
volume, press and hold the
Volume Up or Volume Down
button.
Press the Call button.
Press and hold the Volume Up or
Volume Down button until you
hear a tone.
EN
8

Notes:
• Some features are phone/network dependent.
•Using a mobile device or accessory while driving
may cause distraction and may be illegal. Always
obey the laws and drive safely.
9
EN
STATUS LIGHT
If light shows…
three blue flashes
steady blue
rapid blue/purple
flashes
short blue flash
short purple flash
your headset is…
powering on/off
powered on & searching for a
device
connection successfully
incoming/outgoing call on
phone 1
incoming/outgoing call on
phone 2

If light shows…
slow blue pulse
slow blue flash
slow green flash
slow red flash
slow red flash
short blue/red flash
short red flash
steady purple
your headset is…
on a call
on standby (one phone)
on standby (two phones)
idle (not connected to a phone)
on a call (call muted)
attempting to connect
low battery
in settings mode
Note: After one minute on a call or 20 minutes of
inactivity, the light stops flashing to conserve power,
but the headset remains on. Closing the Boom also
saves battery life.
EN
10

11
EN
ADVANCED
more clever stuff
SECOND DEVICE
Do you use two phones? Or maybe a phone and a
tablet? Connect with both of them.
1 Pair the rst device with your headset as normal (see
“CONNECT & GO” on page 4).
2 Turn off the Bluetooth® feature on the rst device.
3Now pair the second device with your headset as
normal.
4Once paired, to connect with both devices simply
turn them on. You’ll hear “phone one connected”
and “phone two connected” as each device
connects with your headset.
Note: To use headset features like voice dial, redial, or
end call, just use the feature as normal and follow the
voice prompts.

EN
12
CALLER ID
If your phone knows the caller’s number, you’ll hear
“call from <number>” on an incoming call.
Note: This feature is phone/network dependent.
BATTERY READOUT
When you’re not in a call, press the Volume Up and
Volume Down buttons together in standby mode to
hear how much battery talk-time is left on your headset.
Tip: To save battery power, turn off the headset when
you’re not using it.

13
EN
SETTINGS
Press and hold the Call button while turning on the
headset, then follow the voice prompts to turn these
features on/off:
•Language: Select language (English/Spanish)
•Restore Factory Settings: Reset default factory
settings on your headset.
Caution: This feature erases all device pairing
information stored on the headset.
•Voice Interface: Turn voice prompts on/off.
•Caller ID Alert: Hear caller ID for incoming calls.
•Multipoint: Connect your headset to two devices.
•Wide-band: Use HD Audio Plus for increased clarity
and richer sound.
Note: Both the phone and network need to support
wide-band speech.
•Voice Answer: Say “Answer” to receive call.

EN
14
Hubble ConnectTM for Motorola
Hubble Connect for Motorola can greatly enhance
your earbud experience. Download app for free at the
App Store®or Google PlayTM (AndroidTM 4.3 or higher).
• Locate a lost earbud: Locate on a map the last time
your earbud was connected to your device.
Safety instructions for use
To avoid hearing damage, keep the volume at a
moderate level. Avoid listening to music at loud
volume levels for prolonged periods of time as this
may cause permanent hearing damage or hearing loss.
Your hearing is delicate and highly sensitive so please
listen to your music responsibly. For more information
visit the Deafness Research Foundation www.drf.org
Don't use Boom when it is unsafe to do so. For
example, while operating a vehicle, cycling, crossing a
road, or any activity which requires your attention and
ability to hear.
You should be aware of your surroundings and use
Boom responsibly.

Help & more
Manufactured, distributed, or sold by Binatone Electronics
International LTD., official licensee for this product. MOTOROLA and
the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC. and are used under license. Apple
logo is a trademark of Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of Apple Inc. Google Play and
Android are trademarks of Google Inc. All other trademarks are the
property of their respective owners. © 2016 Motorola Mobility LLC. All
rights reserved.
Product ID: MH003
Bluetooth ID: D032280
FCC ID: VLJ-MH003
IC: 4522A-MH003
•Get help: Visit www.motorolahome.com/support
•Find accessories at: www.motorolahome.com
Note: If you’re watching video while using your
earbuds, your audio may be slightly out of sync with
your video.

ZH-CN
MOTOROLA BOOM2
MOTOROLA BOOM2+

1
ZH-CN
产品一览
提高音量键
充电口
(微型 USB)
通话键
按下可接听 /
结束通话
电源开关
展开 – 开启
收起 – 关闭
麦克风
降低音量键
充电状态指示灯：
绿灯 – 电量已满
黄灯 – 电量约 50%
红灯 – 电量低
重要组成部分的简要介绍

ZH-CN
2
配戴
耳勾
听筒

3
ZH-CN
将 USB 线缆插入耳机上的微型 USB 接口，并连接至
USB 电源。
注意：使用前，请先将耳机电量充满。。
提醒：为了节省电池电量，没有使用耳机时应关闭
其电源。
小心：电池的设计可在您的耳机寿命期间内持续使
用。仅可由回收单位拆卸。尝试自行取出或更换电
池将损坏耳机、导致保修失效并可能造成伤害。
为电池充电
启动及操作