2
99282GB- GORILLA AUTOMATIC - REV. 02
WARNING
The specications of this product emphasise maximum importance for the safety of people (are essential to its compliance with EN
1125). It is forbidden to introduce modications to the product that are dierent from those described in these instructions.
The anti-panic device has been certied for use on single doors no larger than 2520 x 1320 mm (H x W) with weight over 200 kg.
Check that the reference number for the lock corresponds to the reference number for the actioning device.
Where the contrary is the case, correct functioning of the lock is not guaranteed.
As required by regulations, we recommend the owner or his authorised representative to carry out the following checks relative to
ordinary maintenance at least once a month:
- inspect and action the emergency exit device to verify that all components are in a satisfactory operational condition;
- check that the holes in the iron receiver are not blocked.
- check that no locks or other blocking devices have been added to the door in addition to the initial device
- verify, using a dynamometer, the operating forces required to open the exit device. Verify that operating forces have not changed
signicantly from those recorded at the time of installation.
The lock operating device should be lubricated, using PTFE dry lubricant (specic for locks), once a year or whenever a stiening of
the mechanisms is detected. Do not use oil or other lubricants: the use of such substances promotes the deposit of dust and fragments
that may aect the correct operation of the lock.
General instruction
Mottura Serrature di Sicurezza S.p.A., thanks you for your condence in choosing this product and recommends:
· to read the instructions carefully before proceeding with the installation;
· to hand over all the instructions to the user by the installer;
· to keep the instructions for future reference and attach the receipt to validate the warranty;
· to contact the dealer only if a problem occurs.
The characteristics of the products described in these instructions may be subject to change by Mottura Serrature di Sicurezza S.p.A. at any time
without prior notice.
Warranty terms
This product tested by Mottura Serrature di Sicurezza S.p.A. is guaranteed against all manufacturing defects for the duration of the period stipu-
lated by applicable Italian legislation from the date of purchase demonstrated in a scal receipt.
Guarantee claims may only be accepted upon presentation of the scal sales receipt, containing the details identifying the product, to technical
support personnel. The guarantee covers the replacement or repair of parts found to have manufacturing defects. The guarantee does not cover
transport costs to and from the technical support centre, which remain at the sole expense of the customer. In the event of a recurring fault of
the same cause, or of an unrepairable fault, Mottura Serrature di Sicurezza S.p.A., at its sole discretion, may decide to replace the entire product.
The guarantee will continue to cover the replacement product until the expiry of the original contract.
If a home call-out should be necessary, the customer is required to pay - if asked to- a call-out fee for the travel expenses of the authorized
service personnel. The customer is solely responsible for any transport damage in the event of direct shipment, or the sole responsibility of the
authorised technician where the product is collected and transported by the technician.
Limited responsibility
Not covered under warranty are damages resulting from the improper installation not in accordance with the instructions attached to the pro-
duct, negligence, carelessness or inappropriate operation, maintenance by unauthorized personnel, transport without due care and attention
and in any case by circumstances that cannot result from manufacturing defects.
Mottura serrature di sicurezza S.p.A. declines any liability for possible damages caused to persons or property resulting from the failure to obser-
ve the indicated precautions for use.
Each and every part (in particular, lock, switchlock, bars) of GORILLA locks is certied by ICIM according to reference
standards. Any modication of the product as a whole, or the installation in disregard of the instruction manual will
automatically void the certication. In this case the installer is responsible for conformity with the reference standards.
General notes
In order to ensure the smooth operation of the lock and the anti-panic device, check the condition of the door (atness, sturdiness and rigidity).
The door and frame must be built of suciently rigid material, such as welded steel or aluminum proles, to ensure that any distortion during
use does not exceed 5 mm at any position of the lock attachment points. Also check that the device and the door open and close without any
obstruction. If the panic exit device is to be installed on a glass door, the glass MUST be tempered and laminated. Panic exit devices are not
intended to be used on doors that open in both directions (entrance and exit) unless specically designed by the manufacturer.
NOTE: Declaration of Performance available on the website at the following link
https://www.mottura.it/en/download/product-certications/antipanic-devices
