NAMCO Tekken Tag Tournament User manual

INTRODUCTION
Thank you very much for purchasing TEKKEN TAG TOURNAMENT PC BOARD KIT (hereafter called
“this product”).
This operation manual explains the following:
l Installing and connecting this product to a general-purpose game cabinet (hereafter called
“cabinet”) safely,
0 Adjusting this product for operation safely,
0 Operating this product safely,
. .
+-VT
l Dismounting, safekeeping, and transporting this product safely,
l Disposing this product safely,
0 Making full use of the efficiency of this product to operate it right.
Reference for this product and/or for repair:
Contact your distributor to make inquiries about this product and/or about repair.

1. SAFETY PRECAUTIONS -
Be sure to read this part for safe use -
To the owner:
0 When the owner of this product entrusts the other person(s) to install this product on the cabinet, to
connect, to adjust for operation, to operate, to inspect, to clean, to troubleshoot, to disassemble. to
keep, to transport and to dispose, direct such a person(s) to read the applicable part of this manual
before conducting the task and to observe the instructions.
0 When reselling this product, always attach this operation manual to the PC Board.
l-l Level of Danger
In this operation manual, the matters that require attention are classified as follows according to the
level of the danger:
A
! WARNING: _ Players and/or technicians can be killed or seriously injured if such
danger cannot be avoided.
A
! CAUTION: Players and/or technicians can be slightly injured if such danger
cannot be avoided.
T’he matters that require attention not concerning safety but functions shall be indicated with the
mark below.
w : The notices concerning the functions and protection of the product.
l-2 Readers of t@s operation manual
This operation manual is written for staff of a location operating amusement game machines. But
the part noted with “To be serviced by a qualified service technician only” on the Table of Contents
and on the title of each chapter is written especially for a qualified service technician. Such a task
should be conducted only by a qualitied service technician who would fit the following
requirements.
A qualified service tekhnician :
* A person who works for designing, manufacturing, inspecting, and maintenance servicing at an
amusement machine (AM) manufacturer, and a person who has technical knowledge of electrical
engineering, electronics, and mechanical engineering equivalent to a graduate of a technical high
school or more, and conducts maintenance services (repair) of an AM equipment on a daily basis.
-l-

1-3 Safety Precautions
1-3-1 General Safety Precautions
7 A WARN’NG
0 Do not dismount nor modify this product. DOflat conduct any works not described in this operation
manual. Otherwise an electrical shock or fire may occur.
0 This product is designed for indoor use only. Do not install, connect, or operate this product
outdoors. It may cause a fire or electrical shock.
0 Be sure to use the replacement parts specified by Namco Ltd. Using substitute parts may cause a fire
or electrical shock. Contact your distributor to order parts. The replacement parts are listed under
“11. Replacement Parts List” on p.56.
l Do not perform any works with wet hands. Otherwise it may cause an electrical shock.
0 Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet before
conducting any works such as installation and connection (except transferring the data to be displayed
on the Namco-made CYBERLEAD cabinet), inspection, cleaning, troubleshooting, disassembling.
Otherwise an electrical shock may happen.
l-3-2 Safety Precautions When Installing and Connecting
-..
A
!WARNING :
When connecting to the cabinet corresponding to JAMMA standard:
0 The power source on the cabinet connected to the JAMMA edge connector should fit the following
requirements:
-Voltage allowable error for +5V should be +5%, Amperage should be 2SA or more
-Voltage allowable error for +lZV should be ti%, Amperage should be 2A or more
If the power source does not conform to this requirement, it may cause a fire.
When c?nnecting to the cabinet corresponding to JAMMA VIDEO standard (JVS):
0 The power source on the cabinet connected to the power cable should fit the following requirements:
-Voltage allowable error for +5V should be G%, Amperage should be 2.5A or more
If the power source does not conform to this requirement, it may cause a fire.
7-
--

l-3-3 Safety Precautions When Operating
I A WARNING :
-.
0 Should any off-flavor or noise occur, turn OFF the power switch of the cabinet immediately and stop
operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the
machine is kept operating without solving the trouble, it may cause an electrical shock or fire.
0 Make sure that installing and connecting were conducted in accordance with the instructions and the
procedure specified in this operation manual (Ref. “5. INSTALLING AND CONNECTING” on p-9)
before operation. If it is not installed and connected correctly, it may cause a fire, electrical shock or
machine trouble.
l-3-4 Safety Precautions When Disposing
0 Do not throw this product into a fire. A lithium battery used in this product may blow to cause injury.
0 When disposing this product, collect, transport, and scrap it in accordance with law and orders.
0 If entrusting others to collect. transport, and scrap this product, hire specialists in each of such work.
-3-

TABLE OF CONTENTS
INTORDUCTION
1. SAFETY PRECAUTIONS - Be sure to read this part for safe use -
....................................................
1
l-1 Level ofDanger .............................................................................................................................. 1
1-2 Readers of this operation manual .................................................................................................... 1
l-3 Safety Precautions.. ......................................................................................................................... 2
1-3-1 General Safety Precautions.. ................................................................................................. 2
l-3-2 Safety Precautions When Installing and Connecting..
.......................................................... 2
l-3-3 Safety Precautions When Operating ..................................................................................... 3
l-3-4 Safety Precautions When Disposing.. ................................................................................... 3
TABLE OF CONTENTS ._............................................................................................................................. 4
2. SPECIFICATIONS . . . . . . . . . . . . . . . . .._.............................................................................................................. 6
3. CHECK OF PACKAGE . . . . .._.................................................................................................................. 7
4. COMPONENTS . .._....._..........................................................................................................................,. 8
5. INSTALLING AND CONNECTING -To be serviced by a qualified service technician only L..
...... 9
5-l Before Installing (Both for m, m)
.......................................................................................... 10
5-2 Installing the PC Board on the Install Board of the Cabinet
(Both for m, m)
....................................................................................................................... 11
5-3 Connecting to the Cabinets Corresponding to the JAMMA Standard m ................................. 13
5-3-l Checking the JAh4MA Edge Connector m ...................................................................... 13
5-3-2 Checking the Extended Edge Connector m ..................................................................... 14
5-3-3 Connecting to the Control Panel m
.................................................................................. I5
5-3-4 Connecting to the Speaker m ........................................................................................... 17
5-3-5 Connecting to the connectors m ...................................................................................... 18
5-4 Connecting the Product to the Cabinet Corresponding to JAMMA VIDEO Standard (JVS)
ma ................................................................................................................................................ 20
5-4-l Connecting to the Control Panel m ............................................................................... 20
542Connection of Cables m
................................................................................................ 21
5-5 Pasting the Stickers (Both for m, m) ...................................................................................... 23
6. ADJUSTMENT FOR OPERATION ...................................................................................................... 24
6-1 The Basic Knowledge of the Adjustment
.......................................................................................
24
6-l-l Adjustment Switches, Knobs ................................................................................................ 25
6-l -2 Selecting the Adjusting Items
...............................................................................................
26
6-l-3 Finishing the Test Mode .......................................................................................................
28
-4-

6-2 Display Test (Check/adjustment of the display) .............................................................................
28
6-2-l Common Operation .............................................................................................................. 79
_
6-2-2 CONVERGENCE (Checking/adjusting the size, position, aspect ratio, distortion of the
picture) .................................................................................................................................. 30
6-2-3 COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of the picture
signal outputted by the PC board) ........................................................................................ 32
6-3 SWITCH TEST............................................................................................................................... 34
6-4 SOUND TEST (Test/setting of the sound) ..................................................................................... 35
6-5 JVS CABINET OPTIONS (Setting VIDEO SYNC
on the cabinet corresponding to the
JAMMA VIDEO standard (JVS)) m ....................................................................................... 36
6-6 GAME OPTIONS (Setting of the game options) ........................................................................... 38
6-7 COIN OPTIONS (Setting of play fees) .......................................................................................... 40
6-8 A.D.S. (Checking the data on playing results in the past) .............................................................. 42
6-9 DATA CLEAR (Clearing various data, initializing to default settings) ......................................... 42
OPERATION .......................................................................................................................................... 45
7- 1 Persons Not Recommended to Play ................................................................................................ 45
7-2 Restrictions When Operated ........................................................................................................... 45
7-3 How to Play ..................................................................................................................................... 46
INSPECTION &CLEANING, TROUBLESHOOT-ING
-To be serviced by a qualified service technician only -
................................................
. .................... 47
8-l Inspection &Cleaning .................................................................................................................... 47
8-2 Troubleshooting .............................................................................................................................. 48
Disassembling, Safekeeping, Transportation .......................................................................................... 50
9-1 Disassembling -To be serviced by a qualified service technician only -.
..................................... 50
9-2 Safekeeping ..........
. .......................................................................................................................... 52
9-3 Transportation ................................................................................................................................. 52
10. DISPOSAL _..__............__........................................................................................................................... 53
11. ’ APPENDIX A.
-Control Panel Layout
-Electrical Diagram
............................................................................................ _................
54
The chapters marked m are indispensable for installing this product to the cabinets corresponding to the
JAMMA standard.
The chapters marked m are indispensable for installing this product to the cabinets corresponding to the
JAMMA VIDEO standard (JVS).
-5-

2. SPECIFICATIONS
Item
Description
I
I
Corresponding Standard JAMMA standard * 1
JAMMA VIDEO standard (JVS) *2
I
1Dimension (268mm
x 230mm x 30mm
I
Weight
Input power source
58Og
[Connected to JAMMA standard terminal ]
+5V 55% (2SA or more) and +12V ?5% (2.0.4 or more)
[Connected to JAMMA VIDEO standard (JVS) renninal]
+5V 55% (2.5A or more)
Restriction Indoor use only
Temperature : 0°C - 50°C. Humidity : 10% - 85% (no condensation)
Cabinets applicable to connect Cabinets corresponding to JAMMA standard
I Cabinets corresponding to JAMMA VIDEO standard (JVS)
Direction of the monitor
Direction of the monitor : Sideways
and the monitor signal
Type of scanning retrace line : non-interlace
Synchronizing signal : Switchable to composite I separate *3
Horizontal synchronizing frequency : 15.7.5kI-I~
Vertical synchronizing frequency : 60.OHz
Networked game play Available only with the cabinets corresponding to JAMMA VIDEO standard
(JVS). (Install fwo cabinets linked with cables. Need one PC board only.)
Control panel
[Pair control panel (10 be used for 2P play in one cabinet)]
g-direction joystick 1x2
Button switch 5x2
Start switch 1x2
[Single control panel (to be used for networked play by connecting two cabinets
with cables)]
Each cabinet should have:
g-direction joystick I
Button swirch 5
Start switch 1
1 How to install it on cabinets 1Fix to the wooden install board of the cabinet
I
*l JAMMA standard (JAMMA STANDARD: abbreviated as IS)
Standards on the edge cdnnectors for video game machine PC boards provided by Japan Amusement
Maihine Manufacturers Association (JAMMA) in 1986
+2 JAMMA VIDEO standard (JAMMA VIDEO STANDARD; abbreviated as JVS)
Standards on connection between video game machine PC boards and other support devices provided
newly by Japan Amusement Machine Manufacturers Association (JAMMA) in 1996
*3 Effective only when installing it on the cabinets corresponding to JAMMA VIDEO standard (JVS)
-6-

3. CHECK OF PACKAGE
This product includes the following items:
PRE-KIT A, TEKKEN TAG TOURNAMENT
No.
Part No. Description
1 TM-08898-00 Assv. Buttons and Joystick
2
TT40-0888500 De&, Side Panel, Left
3
TT40-0888501 Decal, Side Panel, Right
4
lT40-08887-00 Decal, “TAG”
5
TT40-08888-00 Decal, Marquee
6 TT40-08889-00 Decal, Control Panel
7
lT40-08890-00 Decal, “PUNCH”
8
lT40-08891-00 Decal, “KICK”
9
lT40-08892-00 Decal, “PLAYER 1”
IO
lT40-08893-00 Decal, “PLAYER 2”
11
lT40-08894-00 Decal, Tekken Tag Tourn. Logo
12
lT40-08899-00 Poster, Game Promo
13
lT50-08897-00 Harness, JAMMA 56 pin w/tag
14
TT95-08896-00 Cover, Control Panel
Includes 48 pin JAMMA
i5 VG05-06607-00 Mounting Feet, PCB w/screws
16 VG40-08751-00 Poster, AAMA ratings
17 VG44-07943-00 Label, Epileptic Warning
18 VG46-02653-00 Label, FCC
19 VG78-05265-00 Assy, Housing and Ferrite Bead
PRE-KIT B, TEKJSEN TAG TOURNAMENT
No.
Part No. Description
1 TTO3-08884-00 PCB Kit, Tekken Tag Tournament
2
lT40-08886-00 Card, Game Instructions
3
TT40-08910-00 Card, Move List
4
TT450889500 Manual, Game Kit
Qty.
2
i?
2
2
2
1
1 bag of 4
1
2
Qf-Y.
1
1
*NOTES:
lBe sure to check that all items are included.
lIf there is something missing, contact your distributor.
.Save the packing materials in case of storage and transportation of this product.
Refer to chapter “Il. REPLACEMENT PARTS LIST” on p. 54 for the service parts.
-7-

4. COMPONENTS
Option switch
,- Parts mounted side
Terminal for the J
Terminal for the extende
edge connector
Speaker volume
cabinet corresponding to
JAMMA VIDEO standard (JVS)
(Ref. p.22 for details)
PC Board
Wire
Extended edge
preventive key
Extended Edge Harness
-8-

5. INSTALLING AND CONNECTING
-To be serviced bv a aualified service technician onlv -
n
! WARNING.:
l Always turn off the power switch of the cabinet and unplug the power cord from an electrical outlet
before conducting any work, except the work for “5-4-3 Transferring the data to be displayed on the
Namco-made CYBERLEAD cabinet”. Otherwise an electrical shock may occur.
0 This product is designed for indoor use only. Do not install and connect this product outdoors. It may
cause a fire or electrical shock.
m 0 A service technician should not be charged electricity when installing and connecting the
product. Static electricity may cause this product breakdown or damage.
lDo not attempt to perform conductivity test using a multi-meter. Even an internal voltage
of a multi-meter may damage the IC of the PC board.
This product is available for either cabinet, the one corresponding to JAMMA standard, or the one
corresponding to JAMMA VIDEO standard (JVS), however, connecting procedure is different each other.
* Check if your cabinet is applicable to this product referring to “2. SPECIFICATIONS” on p.6.
Chapters in this operation manual corresponding to each standard
Check the standard of your cabinet, and read the following chapters in accordance with that standard.
0 Connecting to the cabinet corresponding to JAMMA standard:
Read the chapters “Both for m, m” on pages 10 -12,23, and the chapters “for m” on pages 13 -
19.
l Connecting to the cabinet corresponding to JAMMA VIDEO standard (JVS):
Read the chapters “Both for m, m” on pages 10 -12.23, and the chapters “for m” on pages 20 -
22.
Cabinet
Namco-made CYBERLEAD cabinet, for example
-9-

5-1 Before Installing (Both for m, m)
You prepare the necessary items to install this product as follows.
Items needed Remarks Reference
Operation manual attached to your cabinet Check the handling of your cabinet.
(+) Countersunk head tapping screw (4 pieces) Fix the lesslocks on the install board of Chapter 5-2
pfi.m
Diameter: one size smaller than the diameter of your cabinet. You may use the furnished (page 12)
installation hole on the side of lesslocks which ones with your cabinet.
fix lesslocks on the install board.
Length: Long enough to fix the lesslocks on the install
board but not too long to stick through the
install board
Lesslock (4 pieces) Keep space between the install board and Chapter 5-2 m,m
Those which have holes to be installed on the install the PC board. You may use the furnished (page 12)
board and holes to install the PC board ones with your cabinet.
Pan head machine screw (4 pieces) Fix the PC board into the lesslocks. You Chapter 5-2 I,=
Diameter: appropriate size for the PC board installation may use the furnished ones with your (page
12)
hole (or internal thread) of the lesslock. cabinet.
Length: Not trm long to stick through the lesslock
when the PC board is fixed. or not too short to
tix it on the lesslock You can adjust the
length by using tk spacer mentioned below in
cases the screws are too long.
Spacer (4 pieces)
Minor diameter.
;;i;e&te size for the screws mentioned
Length: appropriate sire to adjust the length of the
screws above.
Adjust the length of the pan head machine Chapter 5-2
m.m
screws when installing the PC board on
(page 12) -.,
the lesslocks. Not necessary unless the
pan head machine screws are too long.
You may use the furnished ones with your
cabinet.
Solder or caulking, or crimp-style terminal Connect wires to micro switches. Please Chapter 5-3-l m
read the referential chapters to check if (page 13),
they are necessary or not. chapter 5-3-3 m
(page 16).
Chapter 5-34 m
(page 17)
Insulating heat contraction tube and a drier for heat
:ontraction tube Insulate the connection parts of the wires. Chapter 5-3-l
m
Please read the referential chapters to (page 13).
check whether they are necessary or not. Chapter 5-3-3 m
(page 16)
nsulating tape Insulate the edge of unnecessary wires
and connecton. Not necessary when
connecting to the cabinet corresponding
to JAMMA standard with 2
speakerS(sterea specification).
Chapter 5-34 a
(page 17).
Chapter 54-2 m
(page 21)
-lO-

Installing the PC Board on the Install Board of the Cabinet
(Both for m, m>
First install the PC board on the install board according to the following procedure.
1
Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.
2 Read the part on “Installation of the PC board” of the operation manual of your cabinet, and
open the door of the PC board stooge and take out the PC board install board.
When setting networked head-to-head play by using two cabinets corresponding to JAMMA
VIDEO(JVS), you can use either cabinet.
Instal! board
Namco-made CYBERLEAD cabinet, for example
3 In cases other PC boards are connected, remove them in accordance with the procedure
described in the operation manual of your cabinet.
-II-

4 Install the PC board at the center of the install board with the countersunk head tapping screws,
lesslocks, spacers (unnecessary if the pan head machine screws are not too long) and pan head
machine screws, through the four install holes on the PC board.
Lesslock(4 pieces)’
Q 3.6mm 4 points ’
208.6mm
Spacer (4 pieces)
screw (4 pieces)
(+) Countersunk head tapping screw (4 pieces)
m 0 Do not use a metal install plate but a wooden board for installation of the PC board.
Otherwise it may be short-circuited and damaged.
lBe sure to use pan head machine screws to install the PC board on lesslocks. Using
countersunk head screws when spacers are not needed may break the install holes
on the PC board.
0 Clean the cabinet with cleaners if it is dirty with dust.

5-3 Connecting to the Cabinets Corresponding to the JAMMA Standard
5-3-l Checking the JAMMA Edge Connector !H
Use the JAMMA edge connector attached to the cabinet to connect this product to the cabinet
corresponding to the JAMMA standard.
1
Check if the terminal numbers of the JAMMA edge connector of the cabinet conform to the
table of JAMMA edge connectors below. If not, connect wires to that part by soldering or
fixing applicable crimp-style terminals.
w lApply insulating heat contraction tube on the connecting part to prevent short-
circuit.
l - Nothing should be connectedto the blank part of the table below. Otherwise the
PC board may break down.
rSoldered side
JAMMA Edge Connector (%I’ 3.96 mm pitch)
Terminal side
Parts mounted side
I GND 1A 111
GND
I
GND
+5v
+5v
+lZV
Mis-insert preventive key
Cain counter 2
I3 2
C 3
D4
E5
F6
H
I
J 8
K9
GND
+5v
+5v
+12v
Mis-insert preventive key
Coin counter 1
GND
GND
d26
/
e21 GND
f 28 GND
- 13-

2 Check the power source for the cabinet connecting to the JAMMA edge connector and voltage
of the power source for the coin counter of the cabinet.
n
!WARNING :
l The power source on the cabinet connected to the JAMMA edge connector should fit the following
requirements:
- Voltage allowable error for +5V should be ~5% Amperage should be 2.5A or more
-Voltage allowable error for +12V should be L%, Amperage should be 2A or more
If the power source does not conform to this requirement, it may cause a fire.
m 0 Voltage of the power source for the coin counter of the cabinet should be +12V or
+5V. If higher voltage is used, PC board may malfunction.
5-3-2 Checking the Extended Edge Connector @B
To connect this product to the cabinet corresponding to the JAMMA standard, use the extended
edge connector attached to this product.
Check if the terminal numbers of the extended edge connector conform to the following table.
* The extended edge connector shall not be used when installing the product to the cabinet
corresponding to the JAMMA VIDEO standard (JVS).
-..
m lNothing should be connected to the blank parts of the table. Otherwise the PC
board may break down.
Extended Edge Connector (48P 2.54 mm pitch)
PI button switch 4 (blue)
Al5 B15
A16 Bl6
A17 817
Al8 Bl8
A19 B19
A20 B20
A21 B21
A22 B22
A23 B23
A24 B24
Pl button switch 5 (purple)
- 14-

5-3-3 Connecting to the Control Panel m
This product has to be connected to the control panel (see below) described in the chapter “2.
SPECIFICATIONS” (on p.6) to use.
Pl Stan switch
PZ 8-direction joystick
I
1
4 5
4 5
PI button switches
P2 button switches
Turn the power of the cabinet OFF and unplug the power cord from an electrical outlet.
2 Remove the control panel in accordance with the instmctions on “control panel” described in
the operation manual of your cabinet.
3 If the control panel of your cabinet is different from the above drawing, refer to the operation
manual of your cabinet and replace the control panel or add/reduce button switches. If some
switches are reduced, be sure to fill up the switch holes with hole caps.
- 15-

4 Connect the wires of the extended edge harness on the following table to the terminals of PI
button switch 4,5,6 and P2 button switch 4,5,6 on the control panel by soldering or fixing an
applicable crimp-style terminal.
Soldered side
P2 button switch 4 (white/blue)
Terminal side Parts mounted side
A8
P2 button switch 5 (white/purple)
A19 GND (black)
Pl button switch 4 (blue) / BIO
B13
B19
GND (black)
Pl button switch 5 (onrole)
F2 button switch 4,5,6
\Extended
switch 45.6
edge harness
r &WARNING:
0 Always use the extended edge harness specified by Namco Ltd. Otherwise it may cause a fire or
electrical shock. Contact your distributor to order parts. Refer to “11. REPLACEMENTPARTS
LIST,’ on p.56 for details of the replacement parts.
m 0 Apply insulating heat contraction tube on the connecting part to prevent short-
circuit.
0 In case the button switch is three-terminal, the input terminal (wires with the
terminal number A8,A9, AZO,BS,Bl3,B19) of the extended edge harness should
be connected to the N.O. terminal of the button switch. GND of the extended
edge harness (wires with the terminal number B9, BlO) should be connected to
the COM terminal of the button switch.
In case the button switch is two-terminal, these can be connected to either
terminal.
5 Install the control panel on the cabinet.
- 16-

S-3-4 Connecting to the Speaker m
Connect the product to the speaker(s) of your cabinet in the following procedure so that the cabinet
outputs the sound.
First check whether your cabinet has one speaker (monaural) or two speakers (stereo).
l One speaker (monaural)
1 Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet,
2 Conduct a meaSure to prevent short-circuit, for instance, wmp the edge of the unused wire (Al,
B 1) of the extended edge harness with insulating tape.
3 After completing all the following connection, switch to “MONAURAL” in the test mode
(Ref. “6-4 SOUND TEST’ p.37).
.“5-2 Installing the PC Board on the Install Board of the Cabinet (p.ll)
l“5-3-l Checking the JAMMA Edge Connector (p.13)
l“5-3-2 Checking the Extended Edge Connector (p.14)
l“5-3-3 Connecting to the Control Panel (p.15)
l“5-3-5 Connecting to the Connectors (p.18)
* This product is set as stereo spec. as the factory-setting. When used as stereo spec.
with the cabinet of the monaural spec., only the left speaker outputs the,sound.
0 Two speakers
1 Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.
2 Connect the wires of the terminals Al and B 1 of the extended edge harness to the right side
(R) speaker by soldering or fixing an applicable crimp-style terminal in accordance with the
following table.
electrical shock. Contact your distributor to order parts. Refer to “11. REPLACEMENT PARTS
LIST’ on p.56 for details of the replacement parts.
Soldered side
Terminal side Parts mounted side
Speaker R (-) (yellow) Al
BI Speaker R (+) (oran&
- 17-

5-3-5 Connecting to the connectors a
1 Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.
2 Connect the JAMMA edge connector attached to the cabinet and the extended edge connector
in the direction shown below so that the mis-insert preventive key would fit the notch of the
connector slot of the PC board.
m 0 Do not connect the JAMMA edge connector reverse or shifted slightly. The
cabinet and PC board may break down.
Mb-insert
preventive
k
Mis-insert
/
preventive key
-
18-