Nav TV BNT-Audio V2 User manual

BHM
01/13/20
NTV-DOC352
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
BNT-Audio V2
NTV-KIT964
Overview
The BNT Audio Kit V2 allows the user to add auxiliary audio to the factory media systems in
select Bentley vehicles. Currently this kit is not plug & play and must be manually wired in to
the system.
Kit Contents
BNT Audio Switcher
NTV-ASY255
Trigger Harness
NTV-HAR350

BHM
01/13/20
NTV-DOC352
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
AVSWv2 Pin Out
Pin #
Description
Label/Color
1
AV 1 Trigger (+)
White/Blue
2
AV 2 Trigger (+)
White/Red
3
Audio IN Right (2)
Group Label ‘AV2’
4
Audio IN Left (2)
Group Label ‘AV2’
5
--
--
6
Audio IN Right (signal)
Red (OEM INPUT)
7
Audio IN Left (signal)
White (OEM INPUT)
8
Audio IN Left (shield)
Black (OEM INPUT)
9
Video OUT (signal)
Group Label ‘AV OUT’
10
Video OUT (shield)
Group Label ‘AV OUT’
11
Video IN (2) (signal)
Group Label ‘AV2’
12
Video IN (2) (shield)
Group Label ‘AV2’
13
Ground (-)
Black
14
Audio IN Right (1)
Group Label ‘AV1’
15
Audio IN Left (1)
Group Label ‘AV1’
16
--
---
17
Audio OUT Right (signal)
White/Red (OEM OUTPUT)
18
Audio OUT Right (shield)
White/Black (OEM OUTPUT)
19
Audio OUT Left (signal)
White/Gray (OEM OUTPUT)
20
Audio OUT Left (shield)
Group Label ‘AV OUT’
21
Video IN (pass) (signal)
Group Label ‘AV PASS IN’
22
Video IN (pass) (shield)
Group Label ‘AV PASS IN’
23
Video IN (1) (signal)
Group Label ‘AV1’
24
Video IN (1) (shield)
Group Label ‘AV1’
AVSWv2 LED Indication
Wire Side View
LEFT LED: emits when AV1 is powered
RIGHT LED: emits when AV2 is powered

BHM
01/13/20
NTV-DOC352
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Installation
1. Remove the factory radio. This usually requires pulling panels and removing screws that
secure it into the dashboard. Disconnect all associated harnesses and set the radio
aside.
2. Find the audio signal pair (3 wires) that
runs to the amplifier from the factory
radio.
3. Cut the audio signal pair in half. Connect
the wires from the BNT Audio switcher
according to the chart and diagram on the
next page.
4. From the BNT Harness, connect the black wire to Ground (-).
5. Connect the White/Blue wire to a 12v ACC source through a toggle
switch.
6. Connect your AUX source to the RCA labeled ‘AV1’.
7. Connect the BNT-Audio V2 module to the 22-pin connector.
8. Test functionality before reconnecting all dash pieces:
a. With the ignition on, go to the FM radio. Make sure audio is heard
clearly.
b. Connect an AUX audio device to the connected RCA red/white
plugs.
c. Play music through the AUX device.
d. Flip connected switch to the BNT Audio Kit. FM audio should cut
away and AUX audio should be introduced instead.

BHM
01/13/20
NTV-DOC352
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Wire Connection Chart and Install Diagram
Wire Color
Description
Connect to CAR’s:
Car wire color
Black
Shield OUT
Shield Amp Side
Black
Red
Right Channel (+) OUT
Right Channel (+)
Amp Side
Yellow
White
Left Channel (-) OUT
Left Channel (-) Amp
Side
Green
White/Black
Shield IN
Shield Radio Side
Black
White/Red
Right Channel (+) IN
Right Channel (+)
Radio Side
Yellow
White/Gray
Left Channel (-) IN
Left Channel (-)
Radio Side
Green
Amplifier
Side
Radio
Side