Nav TV TOYCAM NTV-KIT057 Manual

BHM
08/15/14
NTV-DOC188
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
TOYCAM
NTV-KIT057/458
Overview
The TOY-CAM kit includes a camera and harness to connect to the factory media screen in
select Toyotas. The signal connection to the radio is plug & play, however the camera will have
to be manually powered. KIT057: TOYCAM no lines / KIT458: TOYCAM with lines (cam image)
Kit Contents
Rear Camera
NTV-CAM5
Plug & Play Harness
NTV-HAR054
Optional 24-pin Adapter
NTV-ASY116
Cam Power Harness

BHM
08/15/14
NTV-DOC188
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Installation
1. Remove the factory radio, disconnect all harnesses and set the radio aside.
2. Install the provided camera on the trunk lid/bumper.
3. Connect the provided Plug & Play Harness to the
camera and run the 4-pin plug side forward to the
dashboard opening.
4. DO NOT USE THE PROVIDED POWER BARREL located on
the camera extension harness! Use the provided separate
Cam Power Harness instead.
5. Connect the red wire from the provided Cam Power Harness to an ACC 12v (+) source
from behind the radio (usually a gray wire, TEST!). Connect the black wire to chassis
ground (-). The radio must see the camera upon vehicle startup in order for the screen to flip
to the camera’s image when in reverse. You MUST connect the camera to an
accessory/ignition source and not a reverse light for proper operation!
6. Connect the 4-pin plug on the provided Plug & Play Harness to the
connector shown here. It is keyed and will only fit in one direction:
Note: If this radio does not possess the 4-pin plug, find the 24-pin
plug. You will need the Optional 24-pin adapter (NTV-ASY116)
available from NAV-TV.
7. Perform this step only if this vehicle requires the
24-pin adapter (see step 5). The adapter
provided (24-pin plug) is only a reference: You
must remove the 4 wires from this adapter and
re-populate each pin into the factory plug in the
same locations. Removing these pins will require
prying the lock-tab up. Connect the 4-pin
camera harness to the 4-pin adapter.

BHM
08/15/14
NTV-DOC188
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
8. Reconnect all the harnesses to radio, reassemble the dash and test by starting the car
and placing it into reverse. The reverse image should activate automatically (whenever
in reverse).
9. Perform this step only if nothing happens on the factory display when the vehicle is
placed into reverse:
a. Locate the Gray, 5-PIN plug on the back side of the radio and find the factory
harness that connects to it (if no harness exists, skip to step d).
b. You’ll likely need to pry the pin-lock free on the back side of the factory
connector (look closely).
c. Insert the pin fully into the connector in the position shown below:
d. Supply a 12v + signal while in reverse only (tap at reverse light) to the free end
of the Rear-Trigger Pin. Verify operation by placing vehicle into reverse.