Nav TV UCT84 F-CAM User manual

UCT84 F-CAM
Front Interface for uConnect 8.4” (RB5, RE2) Systems
NTV-KIT507
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
UCT84 F-CAM
Front Camera Interface for uConnect 8.4” Systems
NTV-KIT507
BHM
4/9/15
NTV-DOC194

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Wire side
Plug & Play Harness
NTV-HAR050
Note: Any remaining wires not shown here are not used for this installation!
*Compatible Dodge Charger, Journey and Chrysler 300 only.
Overview
Allows video to be displayed while the vehicle is in motion and interfaces a front camera into
select uConnect 8.4” Touch screen equipped vehicles. Note: this interface is for adding only a
front camera, not front & rear at this time!
Kit Contents
UCT84 F-CAM Module Pin Outs
Pin #
Description
Color
1
12v Constant Power (+)
Yellow
2
N/A
Red
4
Input 3 (Force Rear Cam)
Pink
8
CAN HI (Radio side)
Pink/Black
9
CAN HI (Car side)
Blue
10
Ground (-)
Black
11
Output 1 (ACC out @ 1 amp)
White/Red
12
Output 2 (Reverse out @ 1 amp)
White/Blue
13
Output 3 (12v out w/ Front DEF)*
White/Purple
17
CAN LO (Radio side)
Pink
18
CAN LO (Car side)
Blue/Black
UCT84 F-CAM Module
NTV-ASY166
USB Cable
NTV-CAB009
VSW Board
NTV-ASY187
F-CAM Harness
NTV-HAR261
VSW Power Harness
NTV-HAR066
DIFF-CAM II
NTV-ASY185

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
VSW Pin Outs
PIN #
Description
Color
1
Video 2 Trigger
White/Blue
2
Video 1 Trigger
White/Red
6
Ground
Black
LED
Description
A
LED: When illuminated, Video 2 is
active
A & B
LEDs: When both illuminated, Video
1 is active
NO LED
LEDs: When none illuminated,
factory video pass through
PIN #
Description
Color
1
RCA Video 2 input (-)
[Shield]
2
RCA Video 1 input (-)
[Shield]
3
Vehicle Video IN (-)
Orange
4
Radio Video OUT (-)
Gray/Orange
5
RCA Video 2 input (+)
White
6
RCA Video 1 input (+)
Green
7
Vehicle Video IN (+)
Dark Blue
8
Radio Video OUT (+)
Gray/Blue
Power/Trigger Connector
Video Input/Output Connector
4
8
B
A
Vid Input
from factory
Vid
Output to
screen
Video 1 input
Video 2 input
5
1
4
1
4
5
8
4
B
1
4
8
8
Normally connected pairs
(When no 12v is present on either trigger)

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Installation
1. Remove the radio (only) from the dashboard. This requires pulling some panels and
a series of screws will hold the radio into the sub-dash.
2. Disconnect all harness from the radio and set the radio aside.
3. Connect the male end of the car’s main radio harnessto the
female end of the supplied Plug & Play T-Harness.
4. Choose an option from the diagrams on page 5 and 6 (FIG 2
or FIG 3 based on which vehicle you’re installing into) and make all connections.
When complete, return here to step 6 to finish the installation.
5. Plug the UCT84 module into the 18-pin connector attached to the plug and play
harness from step 3.
6. Connect the provided VSW Board to both 8-pin connectors (if you haven’t already).
7. Plug the male end of the supplied plug & play T-harnesses to the radio. Note: if this
vehicle possesses an OEM camera, the Camera Harness (see FIG 1 below) will
already be populated. Connect the F-CAM T-harness in between the radio and the
factory plug.
8. Reconnect the remaining plugs to the radio (antennas etc), remount and test for
proper operation.
Rear of uConnect radio
Plug & Play T-Harness
(with module)
Camera Harness (F-CAM
Harness connects here)
FIG 1

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
Connection Diagram (Charger, 300, Journey)
FIG 2
This diagram is for Dodge/Chrysler ONLY! Maserati wiring configuration is on page 6.

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
Connection Diagram (Maserati Ghibli, Quattroporte)
FIG 3
This diagram is intended for Maserati or Dodge/Chrysler

BHM
04/09/15
NTV-DOC194
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
UCT84 F-CAM Operation
Video in motion is always enabled, no user interaction is required.
Video in Motion will allow:
DVD video to be displayed while the vehicle is in motion
Navigation input while moving
Bluetooth operation while moving
*Note: Navigation-based speed indication will not be available while VIM is active.
OEM Rear view camera will work normally in reverse.
Forced Rear Camera
is enabled by pressing
the Rear Defrost Button
twice within 1 second.
Forced Front Camera is
enabled by pressing the Front
Defrost Button twice within 1
second.
Forced Front Camera for Maserati Ghibli and Quattroporte is activated by flipping the
toggle switch connected to the system (FIG 3). This action can be performed in any gear at any
speed.
Double tap
for forced
rear camera
(if equipped)
Double tap
for forced
front camera
NOTE: Forcing cameras through an OEM dash button is only supported with the Dodge Charger, Journey and
Chrysler 300. More models will be added with further development.