Nav TV NTV-KIT422 User manual

MY TOUCH F-CAM
Video in Motion, Control in Motion, Forced Cam
NTV-KIT422
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
JR, BM
11/28/17
NTV-DOC155
rB10

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
2 | P a g e
Kit Content
VIM A Connector Pin outs
Pin #
Description
Color
1
12v Constant Power (+)
Yellow
2
Input 1
Red
3
Input 2 (Sending 12v will force rear camera)
Blue
4
External VIM Activation
Orange
6
LIN Break-Open wire (Camera Side)
Blue
8
CAN Hi (Radio Side)
Purple/Black
9
CAN Hi (Vehicle Side)
White/Black
10
Ground (-)
Black
11
12v Output to VIM module B (pin 4)
Orange
12
Output 2
Blue/White
13
Output 3
White
14
Looped to pin 15
Yellow
15
Looped to pin 14
Yellow
16
LIN Break-Open wire (BCM Side)
Orange
17
CAN Lo (Radio Side)
Purple
18
CAN Lo (Vehicle Side)
White
VIM B Connector Pin outs
Pin #
Description
Color
1
12v Constant Power (+)
Yellow
4
Input from VIM module A (pin 11)
Orange
8
CAN Hi –Radio Side
Green
9
CAN Hi –Vehicle Side
Gray
10
Ground (-)
Black
17
CAN Lo (Radio Side)
Green/Black
18
CAN Lo (Vehicle Side)
Gray/Black
VIM modules A & B
(2x)NTV-ASY166
Plug n’ Play VIM Harness
NTV-HAR241
USB cable (updates)
NTV-CAB009
Wire side
Wire side

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
3 | P a g e
VIM & F-CAM Installation
1. Remove the factory My Ford Touch radio. This requires removing panels and various 7 & 8mm
screws. The trim panels securing the center radio bezel do not need to be fully removed, just
moved out of the way.
a. There are (2x) 7mm screws hidden beneath the airbag module and therefore the airbag
module must be popped out (no need to disconnect entirely). Apply tape for protection
to the dashboard just beneath the airbag before you do this!
b. Remove the passenger airbag assembly by removing the (3x) 8mm screws firing up from
underneath the airbag. Access these screws by dropping the glove box down to the floor
(again, no need to remove it entirely).
c. Remove (or pop free at the right bottom corner) the cluster surround, and pull aside the
trim pieces that surround the radio.
2. Remove the (4x) 7mm screws holding the screen in place.
3. Disconnect all wiring and set the screen aside.
4. Gather the Plug & Play harness from the F-CAM kit.
5. Plug the main LCD harness (male) from the car into the
female side of the F-CAM Plug & Play harness.
6. Gather the ‘A’ and ‘B’ modules, and connect them to their
prospective, labeled connecters.
Steps 7-11 are intended for F150 Raptor’s only, those with an OEM front
camera. If are adding an aftermarket front camera to a standard F150, you must
purchase NTV-KIT437 as well and should refer to that instruction set (pg 5&6) at
this time before returning and completing the install here (begin again with step
12 upon returning).
7. Under the driver’s dash, make a small incision in the rubber harness grommet going through
the firewall on the driver’s side.
8. Connect a 10’ pair of wires to the F-CAM module A: connect one of the wires to pin 6 and the
other to pin 16. Route the free end of the wire pair through the firewall (at your incision), into
the engine bay of the vehicle. Use silicon or 3M strip caulk to seal the incision.

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
4 | P a g e
*Note: When the factory front camera is forced on, the active factory guidelines are not
enabled. Only when the vehicle is in 4L will the active guidelines be available.
13. Optional: If you send 12v (through a toggle) to Input 2 (Blue), it will force the rear camera.
14. Optional: If you send 12v (through a toggle) to Input 3 (Orange), it will force VIM operation.
10. Locate the
gray/violet
wire and cut it
in half.
9. On the
underside of the
hood, traveling
down the
driver’s side, is
the camera
harness. Cut the
harness open at
the bottom of
the hood.
11. Connect the extended wire labeled
“Camera” (pin 6), to the camera side of the cut
gray/violet wire. Connect the extended wire
labeled “BCM” (pin 16) to the vehicle side of
the cut gray/violet wire. Insulate and tape the
connections when finished.
12. Plug the male end of the Plug & Play harness into the factory LCD and test for proper operation (refer
to page 5 & 6 for operation instructions).

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
5 | P a g e
F Series OEM Reverse Camera Modification
•If this vehicle has an OEM reverse camera and you wish to display it at any speed, you
must locate the OEM LIN (data) wire and install an SPDT Relay (not included) to break the
(LIN) wire, whenever it is forced. From the factory, the OEM reverse camera is only
powered on until ~15 mph. Wire a relay to break the LIN wire like shown below (2016 F150
example):
2016 F150: Blue connector
at pass side BCM
Slide gray inner connector
out of blue shell
NOTE: this
modification is not
supported for
SuperDuty vehicles!
PIN 37 LIN wire: cut in half.
Connect Relay
ACC
12v (+)

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
6 | P a g e
VIM & F-CAM (Raptor) Install Diagram

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
7 | P a g e
VIM & F-CAM Kit Operation
Video in Motion
When VIM is activated, AUX video input can be viewed while vehicle is in drive. This feature has to be
enabled every time the key is cycled.
Video in Motion (VIM): Press the Front Defroster Button 2 times within 1 second.
Forced Rear Camera
Double-Tap
Additionally, if you send 12v
(through a toggle) to Input 3
(Orange), it will force VIM
operation.

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
8 | P a g e
This function allows the viewing of an aftermarket
rear camera at any time.
Forced Rear camera: Press Rear Defroster Button 2
times within 1 second.
Factory Front Camera Operation
The front camera can be viewed at any time using the factory procedure for activation.
*Note: Front camera will not display if VIM is enabled!
Double-Tap
2. Scroll to the right until
“Camera Disabled” is displayed.
1. Using the steering wheel
controls scroll down to the Truck
Apps function in the instrument
cluster.
Additionally, if you send 12v (through a
toggle) to Input 2 (Blue), it will force the
rear camera.

BHM
11/28/17
NTV-DOC155
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
9 | P a g e
3. Press the “OK” button on the
steering wheel.
5. To disable front camera:
a. Make sure the cluster is on the Camera options screen
b. Press OK.
4. The front camera will display on
the screen (the active steering lines
will not be displayed), the cluster
will display ‘Press OK to disable’
(
T
h
e
a
c
t
i
v
e
s
t
e
e
r
i
n
g
l
i
n
e
s
w
i
l
l
n
o
t
b