Nav TV C.O.D-F50 User manual

C.O.D-F50
Ford OEM 360 Surround-View Camera Controller
NTV-KIT899
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
BHM
02/01/19
NTV-DOC334

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
2 | P a g e
USB cable (updates)
NTV-CAB009
Overview
The COD-F50 (Camera-On-Demand) kit allows Ford SuperDuty trucks equipped with OEM (5-camera
system) surround view cameras to be displayed on demand, without lock-out restrictions. Additional
features include turn signal cameras, easy force rear cam & force front cam & last known camera
retention (from hard camera button press). NOTE: This kit will NOT program any camera system. This
module is only intended for use in SuperDutys equipped with the OEM trailer package (5-camera
system).
Kit Content
COD-F50 Module Pin Out
Pin #
Description
Color
1
12v Constant Power (+)
Yellow
2
INPUT 1: NOT USED
Red
3
INPUT 2: NOT USED
Blue
4
INPUT 3: NOT USED
Pink
5
RX (OE camera button –button side)
Blue
6
CAN-3 HIGH (camera module)
Blue
7
CAN-2 HIGH (CAN gateway)
Blue
8
CAN-1 HIGH (APIM)
Yellow
9
CAN-0 HIGH (CAN gateway)
Yellow/Black
10
Ground (-)
Black
11
OUTPUT 1: NOT USED
White/Red
12
OUTPUT 2: NOT USED
White/Blue
13
OUTPUT 3: NOT USED
White/Purple
14
TX (OE camera button –module side)
Purple
15
CAN-3 LOW (camera module)
Purple
16
CAN-2 LOW (CAN gateway)
Purple
17
CAN-1 LOW (APIM)
Orange
18
CAN-0 LOW (CAN gateway)
Orange/White
Satellite Switcher Board
NTV-ASY304, NTV-HAR333
Wire side
COD-F50 Module
NTV-ASY301
Plug & Play
T-Harness
NTV-HAR332

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
3 | P a g e
COD-F50 Installation
1. Remove the 8” SYNC 3 screen (radio):
a. Remove the center channel speaker cover on the top (middle)
of the dash (4 clips only) NOTE: this panel is very tight.
b. Remove (2) 7mm bolts securing the top
panel (previously hidden by the speaker
grill).
c. Remove the whole upper shelf panel, it
should be held in by clips only, now.
Disconnect the speaker lead. Set this
panel assembly aside.
d. Remove (2) 7mm screws on top of the climate/screen dash
panel, and then pull panel straight towards you. Disconnect
all harnesses and set the panel aside.
e. Remove (6) 7mm screws securing the screen (APIM) to
the sub-dash. Disconnect all harnesses and set the
APIM aside.
f. NOT SHOWN: the IPM (camera module) is bolted to
the sub-dash directly behind the screen with 7mm
screws. Remove it to connect the T-Harness properly.
Do not attempt to connect to the IPM while it is still
connected to the sub-dash.

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
4 | P a g e
2. Connect the provided (large, main) T-Harnesses
between the vehicle harness and the APIM (screen).
3. Connect the provided SAT-switcher board/harness to
the IPM (directly behind screen). Connect the (OE) IPM
vehicle harness (previously removed) to the SAT-
switcher board.
4. Connect the 8-pin harness from the main T-Harness to the SAT-
switcher board’s 8-pin port.
5. Connect the 18-pin plug to the COD module and secure it in the sub-dash (up underneath the
center-channel speaker) so that nothing rattles. NOTE: No other wires from the main unit are
used for this installation.
6. Return the screen to the sub-dash and reconnect the climate/screen surround panel for testing.
7. Proceed to ‘COD-F50 Operation’.
SAT-switcher board
IPM (camera module)
Rear of APIM (screen)

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
5 | P a g e
COD-F50 Connection Diagram

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
6 | P a g e
*NOTE: to disable turn signal camera activation,
press and HOLD the camera button for 20 seconds
(wait for tone). Once complete, turn signal
cameras will deactivate. Repeat this process to
reactivate TSC at any time.
**NOTE: forcing the rear camera may affect NAV
guidance temporarily. This is a factory limitation.
COD-F50 Operation (SuperDuty)
Once the COD-F50 module is connected properly, all added camera commands are performed
through the factory camera button. Added features are outlined below:
•Single-Press camera button shows rear camera and
rear cam options** (default after ignition), press and
release once again to clear
•Double-Tap camera button shows front camera and
front cam options, press and release once again to clear
•Last used camera image (whether front, rear, cargo or surround view) is
retained when switching back and fourth from radio screen to camera screen via
camera button (instead of default surround view only with each press)
•Turn signals switch to corresponding side view*
(left or right, panned 100%)
•Single-Press camera button shows rear camera and
rear cam options** (default after ignition), press and
release once again to clear
•Double-Tap camera button shows front camera
and front cam options, press and release once
again to clear

BHM
02/01/19
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
7 | P a g e
COD-F50 NOTES
•SYNC 3 radio must be at least Version 3 for all features to work properly. Under SETTINGS, then
GENERAL SETTINGS, look for the SYNC version. The radio system can be updated over the air if
the vehicle is connected to a local WiFi connection. For more detail information, watch this
video: https://www.youtube.com/watch?v=No8fJ7V21Y8
•The IPM T-Harness (camera module T-harness, smaller one) has delicate pins. If the unit is
acting erratically, reseat this T-Harness after checking for bent pins.
•If your unit came with a USB cable and has a serial number, then it is updateable. If you suspect
the unit needs a software update, connect the module to a Windows PC via USB and go to
www.navtvdevice.com. All updates are available on that web page.