Nav TV REC-AV XG User manual

JR, BM
09/03/15
NTV-DOC 144
rB5
1 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]
REC-AV XG
NTV-KIT276
Overview
The REC-AV XG adds video input (including rear camera) for select ‘06-’08 Chrysler/Dodge/Jeep
REC navigation radios. NOTE: The REC radio must possess the 3-pin camera port on the back
for this kit to be compatible.
Kit Contents
REC-AV XG Module
NTV-ASY171
Plug and Play
T-Harness
NTV-HAR087
Camera Input Harness
NTV-ASY142
Audio-IN Harness
NTV-ASY231
AVSW NTV-ASY170
AVSW Harness
NTV-HAR066
USB Cable (updates)
NTV-CAB009
CAN Adapter Harness
NTV-HAR058
(2x) Audio RCA-3.5mm Adapter
NTV-CAB054
(3x) Male
barrel RCA
NTV-CON018
(NTV-KIT224 Optional)

JR, BM
09/03/15
NTV-DOC 144
rB5
2 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
REC-AV Programming
Before the product is installed, be sure the module is programmed for needed functions. To
change any one of the settings, double click the line with the feature to be enabled/disabled.
Down
REC-AV Module Pin Outs
Adjustable Parameter
Description
VES Emulation
Emulates rear seat entertainment for AV input
(Do not turn on if vehicle already has factory VES.)
Rear view camera
Turns on rear camera input to add an aftermarket camera.
(Also required for VES video input.)
12V output when camera is forced
Supplies 12v out of Pin 12 when forced camera is enabled or
the when in reverse
Front view camera
Supplies 12v out of Pin 11 when front camera is activated.
Pin #
Description
Color
1
12v (+) Constant Power
Yellow
6
Relay 1-Common-Video OUT
Yellow
7
RCA Common Shield
[Shield]
8
CAN HI (Radio side)
White/Green
9
CAN HI (Car side)
Brown/Black
10
Ground (-)
Black
11
Output 1 (Front cam 12v out)
White/Red
12
Output 2 (Rear cam 12v out)
White/Blue
13
Output 3 (ACC 12v + out)
White/Purple
15
Relay 1 (normally open) Vid IN
White
16
Relay 1 (normally closed) Cam IN
Red
17
CAN LO (Radio side)
Green
18
CAN LO (Car side)
Brown
Wire side

JR, BM
09/03/15
NTV-DOC 144
rB5
3 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1. Remove the radio from the dash.
2. Plug in the supplied T-harness between the radio and factory connection (22 pin
connector.)
3. Connect the module to the harness and locate in a secure location in the dash (be sure
to program the module for required features before installation.)
4. Run the USB cable from the module to a location that can be accessed in the future, in
case the module needs to be reprogrammed or updated.
Backup Camera:
1. Install backup camera, run the video signal and
camera power to the radio.
2. Plug the video signal into the RCA attached to
the 3 pin plug.
3. The power wire of the camera gets connected to
pin 12 (OUTPUT 2) or pin 13 (OUTPUT 3) of the
filter.
*Do not connect the camera power to reverse lights, otherwise forced camera will
display a blank screen.
VES/AV Input and Rear Camera:
The REC-AV will internally enable VES* and rear camera switching without the need for an
external switcher.
1. Connect the RCA labeled “VIDEO TO RADIO” to the supplied 3-pin to RCA harness.
2. Connect the rear view camera to the RCA labeled “BACKUP CAM”. The power from the
camera can be connected to pin 12
(OUTPUT 2) or pin 13 (OUTPUT 3).
3. Connect the VES/external video
source to the RCA labeled “VIDEO
IN”.
* Factory VES requires a send in
modification for video to be viewed
on the radio.
Installation

JR, BM
09/03/15
NTV-DOC 144
rB5
4 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Front and Rear Camera
1. Connect the backup camera to the Yellow RCA labeled “FACTORY AV” of the AV
switcher.
2. Plug the supplied 3-pin to RCA harness into the
radio. Plug the other end into the Yellow RCA
labeled “AV OUT” of the AV switcher.
3. The Front camera signal goes to the RCA labeled
“V1” of the switcher.
4. The black wire of the switcher goes to chassis
ground.
5. The white/red wire (pin 7) goes to white/red (pin
12) of the REC AV XG module.
VES Input with Rear and Front Camera
1. Connect the supplied 10-pin T-harness
with Red and White RCAs between the
radio and factory harness. (Note that
there may be no factory harness in this
location.)
2. Plug the audio out of external AV
source to the Red and White RCAs.
3. Connect the external AV video to the
Yellow RCA labeled “FACTORY AV” of
the AV switcher.
Shield
(black)
RIGHT
(red)
LEFT
(white)
4. For Audio IN, use the provided 10-PIN
connector with RCA. You will need to
populate the provided connector as shown
here unless this vehicle possess this same
connector with existing wires. If this
connector exists in the car already, populate
the factory connector instead as shown here:

JR, BM
09/03/15
NTV-DOC 144
rB5
5 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4. Plug the supplied 3-pin to RCA harness into the radio. Plug the other end into the
Yellow RCA labeled “AV OUT” of the AV switcher.
5. The Front camera signal goes to the RCA labeled “V1” of the switcher.
6. The Rear camera signal goes to the RCA labeled “V2” of the switcher.
Note - If the vehicle has factory VES installed, DO NOT connect audio T-harness.
Factory VES requires a send in modification for video to be viewed on the radio.
When the optional switcher is being used, do not use the RCAs on the REC-AV Plug-n-Play
harness.
Multiple video inputs using the optional switcher (AVSW)
When installing rear camera, VES emulation and front camera, an optional switcher is required.
This will allow multiple video inputs to be sourced in.
Switcher
REC-AV Output
Black
Chassis Ground
White/Red (pin 7)
White/Red (pin
12)
White/Blue (pin 8)
White/Blue(pin
11)
Switcher connections
Input Source
Factory AV
External Video source
AV out
3-pin to RCA plug to
Radio
V1
Front Camera
V2
Rear Camera
*Note - The audio inputs/outputs are not used.

JR, BM
09/03/15
NTV-DOC 144
rB5
6 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Operation
VES: Press the ‘MODE’ button until VES tab is
highlighted. Once the tab is selected, the video
input will automatically be displayed.
Reverse Cam/Forced Cam: Double press the main power button on the radio. This will
automatically display the backup camera regardless of gear or motion of the vehicle. To return
to the factory screen, double press the main radio power button again.
Front Camera: When the Front view camera
feature is enabled (through programming),
every time the radio is placed into forced
camera mode it will toggle between the rear
camera and the front camera. The order is as
follows: Radio > Rev Cam > Front Cam > Radio
Double tap