Nav TV Volvo VIM User manual

JR, BM
04/07/14
NTV-DOC092
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
Volvo VIM
NTV-KIT298
Overview
The Volvo VIM kit enables video in motion (VIM) and navigation control in motion (CIM) in
select Volvo vehicles. This installation requires no cutting of any factory wires and is fully Plug &
Play behind the media screen.
Kit Contents
Volvo Cam module
NTV-ASY160
USB Cable (updates)
NTV-CAB009
Plug & Play T-Harness
NTV-HAR204 & NTV-HAR207

JR, BM
04/07/14
NTV-DOC092
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Volvo VIM Module Pin Outs
Pin #
Description
Color
1
12v Constant (+)
Yellow
5
-not used-
Gray
6
-not used-
Blue
8
CAN HI (Radio Side)
Green
9
CAN HI (Vehicle Side)
White
10
Ground (-)
Black
11
Output 1 (12v w/ CAN)
White/Red
12
Output 2 (12v w/ REV)
White/Blue
13
Output 3
White/Purple
14
-not used-
Gray/White
15
-not used-
Pink/Black
16
-not used-
Pink
17
CAN LO (Radio Side)
White/Green
18
CAN LO (Vehicle Side)
Brown
Module Programming
1. The Volvo Cam module will come preprogrammed with the most popular working file,
but you may need to adjust it for your particular Volvo type/year.
2. Refer to http://www.navtv.com/page/19/downloads.html and download the ‘Volvo
Cam’ Updater (towards the bottom of the page, 10/30/2013 date stamp)
3. After downloading, unzip the compressed folder into another folder (make a new folder,
name it ‘Volvo’)
4. If you’ve never updated a Nav-TV module before, you’ll need to install one USB driver
also found on the Nav-TV downloads page (at the very top, first downloadable link).
5. Open the Volvo Updater found in the extracted folder from step 3.
6. Connect the Volvo Cam module to the computer using the provided USB to mini-USB
cable.
7. The ‘USB Device’ field should populate after 5-10 seconds.
8. Click the 3 dots at the top right of the updater window. Navigate to the same extracted
folder from step 3. Select the ‘Volvo Cam.enc’ file and press ‘Open’.
9. Double click ‘ON’ for VIM or address in motion to adjust ON or OFF.
10. Double click ‘ON’ for Rear view camera to adjust ON or OFF.
11. Double click ‘off’ for Front view camera to adjust ON or OFF.
Wire Side

JR, BM
04/07/14
NTV-DOC092
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
12. Double click ‘S60’ and a new
window will appear. Select from
the drop down according to which
Volvo type you’re installing the kit
into and then press ‘OK’.
13. Press the ‘Update’ button and wait
for the loader to finish updating.
14. Disconnect the module from the
computer, reconnect to the T-
Harness in the car and retest for
proper operation.
Click here to
select file
Click here to
select car

JR, BM
04/07/14
NTV-DOC092
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Installation
1. Access the main LCD screen by removing the panels surrounding it. This usually involves
pulling the panels and removing Torx screws.
2. Remove the Volvo LCD by
removing the (4x) Torx T25 screws
that secure it into the dashboard
and disconnect all plugs connected
to the screen. Set the Screen aside
for now.
3. The Volvo VIM kit includes (2x)
T-Harnesses. You must determine which is needed for your vehicle by examining the
CAN wires on the male side of the provided Power T-Harness:
4. Plug the factory power/CAN harness into the female side of the supplied T-Harness.
5. Plug the Volvo Cam module into the 18-pin connector located on the supplied T-
Harness. The LED on this module will light up solid whenever CAN is active in the car.
6. Connect the male end of the supplied Plug and Play harness into the Volvo screen.
Reconnect the remaining plugs to the screen and test for proper operation before
reassembling dash.
Back of Volvo Screen
Compare the CAN wires on this plug with the factory Volvo screen’s plug: make
certain the wire locations match (are in the same position).
NTV-HAR207
NTV-HAR204

JR, BM
04/07/14
NTV-DOC092
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
Video in Motion (VIM) Operation
VIM and navigation* entry in motion is enabled when the unit is shipped. No user activation is
required for most vehicles, but if the module does not function, press the Parking Sensor
button. This will enable VIM and allow the user to watch DVD movies or control the navigation
when the vehicle is in motion.