NBB SR8299 User manual

Assembly Instructions
Shelter Type: SR8299
SR8299-01-28102021-USA

14
15
10
14
10 11
1
4
4
11
9
5
5
9
2
8
16
17
6
7
3
15
12
14
14
2
EXPLODED VIEW

3
PARTS LIST
ITEM
NO.
PART
NO.
DESCRIPTION
Size (inch) IMAGE
QTY.
1
S1
Full Frame
78.74 x 40.74
5
2
CB1
Corner Bracket - CB1
4.3 x 4.3 x 1.57
8
3
JF1
Joint Flat - JF1
4.33 x 1.57
7
4
P1
Post Frame - P1
78.74 x 40.74
2
5
ST5
ST5 Roof Tie Bar
60.75 2
6
P5
P5 POST
77.15 x 1.57 x
1.57 1
7
JFT
Bracket
8.66 x 5.9
1
8
DR
Rafter Bracket
4.3 x 1.6 x 2
12
9
DR2R
DR2R Rafter
92.32 4
10
DR2I
DR2 infill panel
85 x 15.75
2
11
DR2PO
DR2 Roof Panel Outer
92.32 x 41.54
2
12
DR2PI
DR2 Roof Panel Inner
40.75 x 92.30
1
13
DR2T
DR2 Roof Trim
92.32 x 3.15
4
14
DRATO
DR Ally-Angle Trim Outer
2 x 2 x 41.5
4
15
DRATI
DR Ally-Angle Trim Inner
2 x 2 x 40.75
2
16
FT1
FT1 BRACKET
1.57 x 1.57 x
3.94 5
17
FT3
FT3 Bracket
1.57 x 3.15 x
4.17 4
18
EC40
Plastic end cap
1.6 x 1.6
6

4
FIXINGS
Tools required:
Drill/Screwdriver
Mallet
17mm Wrench
T25 Torx bit
Fittings Bolt set M10 T25 T38 BTANCM12100
M10 x 60mm Nut Washer
1" Tech
screw
1.5"
Tech
screw
Black
Caps
M10/12 x 100 mm
Concrete Bolt
Pack A+B
33 33 66 136 40 66 11
Image

MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
Please note 1.5" Tec Screws
are for roof panels only
CB1
CB1
CB1
CB1
CB1
CB1
JF1 JF1
CB1
CB1
JF1
P1
P1
ST5
JF1 JF1
JFT
ST5
P5
ENSURE CORRECT
ALIGNMENT ON
CORNERS
JF1
CB1 CB1
CB1
JF1
JF1
JF1JF1
JFT
DETAIL A
SCALE 1 : 10
DETAIL B
SCALE 1 : 10
DETAIL C
SCALE 1 : 10
DETAIL D
SCALE 1 : 10
Step 1
Assemble S1 frames to make up the main structure using CB1
brackets for the corners and JF1 brackets for the straight joints.
Attach P1 post to the S1C Frame using CB1 and JF1 brackets.
Brackets as shown below.
5

DR2R
DR2I
DR BRACKET
DR2I
DR2R
DR2R
DR2R
40.75 40.75 40.75
RAFTER PLACEMENT
6
Step 2
Attach DR2R rafters using DR brackets. Secure the END PANELS (DR2I) to frames
using tec screws. The end rafters need to be placed in position at the same
time as the DR2I

DR2PO
DR2PO
DR2T DR2T
DR2T
DRATO
DRATO
DRATO
DRATO
DRATI
DRATI
DR2T
DR2PI
7
Step 3
Attach the DR2PO and DR2PI Panels to the top of the rafters, with the DR2PO
on either end and the DR2PI in between. Seal the gap between the panels
using the DR2T strips. Attach the DRATO and DRATI Trim parts to the lower part
of the rafters as shown below.

FT1 x5
FT3 x4
8
Step 4
Move the shelter into its desired position and attach the foot brackets
FT1/FT3 before fixng in place.

40.75 81.87
39.17
41.12
38.27
77.44
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 8" oversized on all 4 sides.
9

10
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
All Parts and Fixings checked by:
Print Name: Signature: