NBB SR8301-F User manual

Assembly Instructions
Shelter type: SR8301-F
SR8301-F-01-07092021-USA

13
13
15
16
11
5
4
11
7
82
2
11
10
1717
18
6
3
5
9
12 14
2
EXPLODED VIEW

3
PARTS LIST
ITEM
NO. PART NAME
DRG
NUMBER
Size (inch)
IMAGE
QTY.
1 S1C Frame S1C
78.74 x 40.74
2
2 S3C Frame S3C
78.74 x 20.3
2
3 JF1 Bracket JF1
8.7 x 1.6
2
4 CB1 Bracket CB1
4.3 x 4.3 x 1.6
8
5 ST15 Tie Bar ST15
20.15 x 1.57 x 1.57
2
6 JFT JFT
8.66 x 5.9
1
7 ST3 Roof Tie ST3
81.1 x 1.57 x 1.57
1
8 Post P5 P5
77.15 x 1.57 x 1.57
1
9 DR Bracket DR
4.3 x 1.6 x 2
8
10 AR1R 1m Pitch Rafter AR1R
45 x 11.8 OA
3
11
AR1IS 1m Pitch Infill
Panel Shallow
AR1IS
45.2 x 13.5
2
12
ARFS2 Apex Roof F
section 2m
ARFS2
83.1 x 2 x 2
2
13
AR1POA Roof Panel
outer alu
AR1POA
41.5 x 24.4
4
14
AR1CLT2 1m Apex
Roof centre lower trim
2m
AR1CLT2-02
82.9 x 3.1
1
15
AR1CUT2 1m Apex
Roof centre upper trim
2m
AR1CUT2
83.1 x 3.9
1
16
AR1TS 1m Apex Roof
Trim strips
AR1TS
24.8 x 2.3
2
17 FT1 BRACKET FT1
1.57 x 1.57 x 3.94
3
18 FT3 Bracket FT3
1.57 x 3.15 x 4.17
3
19 40x40 Plastic End Cap EC40
1.6 x 1.6
6

4
FIXINGS
Tools required:
Drill/Screwdriver
Mallet
17mm Wrench
T25 Torx bit
Fittings Bolt set M10 T25 T38 BTANCM12100
M10 x 60mm Nut Washer
1" Tech
screw
1.5"
Tech
screw
Black
Caps
M10/12 x 100mm
Concrete Bolt
Pack A+B
33 33 66 136 40 66 11
Image

21.93
83.07
20.35
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
Please note 1.5" Tec Screws
are for roof panels only
ENSURE CORRECT
ALIGNMENT ON
CORNERS
CB1
CB1
JF1
S1C
S1C
S3C
S3C
JF1
CB1
CB1
JF1
CB1
Step 1
Assemble S1C and S3C frames to make up the main structure using CB1
brackets for the corners and JF1 brackets for the straight joints.
5

ST15
ST15
CB1
CB1
JFT
ST3
P5
CB1
CB1
P5
ST15
ST15
CB1
CB1
CB1
CB1
JFT
ST3
6
Step 2
Attach ST15 Tie bars to S3C frames using CB1 Brackets. Assemble the
ST15 Tie Bars with the ST3 Tie bar and the P5 Post, using the CB1 Corner
Brackets and the JFT Bracket as shown below.

AR1IS
AR1IS
AR1R
AR1R
AR1R
DR
DR
DR
DRDR
DR
AR1IS
AR1IS
AR1R
AR1R AR1R
DR
DR
DR
DR
DR
7
Step 3
Attach AR1R rafters using DR brackets. Secure the AR1IS to S1 frames using tec
screws. The end rafters need to be placed in position at the same time as the
AR1IS .

ARFS2
ARFS2
AR1CTL2
ARFS2
ARFS2
AR1CTL2
8
Step 4
Attach the AR1CLT2 to the top of the rafters. The ARFS2 parts are to be
attached to the lower part of the rafters as shown below.

AR1TS
AR1POA
AR1CUT2
FT1
FT3
FT3
FT3
FT1
FT1
AR1CUT2
AR1POA
AR1TS
AR1TS
FT1
FT1
FT1
FT3
FT3
FT3
9
Step 5
Attach the AR1POA roof panels to the top of the rafters.
Cap off the top using AR1CUT2 trim as shown.
Use the AR1TS strips to cover the gaps between the panels.
Once the shelter is in the final position and square, it can be secured to
the ground using the FT3 and FT1 brackets.

39.13
42.64 39.17
42.28
45
83.08
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 7.8" oversized on all 4 sides.
10

11
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
All Parts and Fixings checked by:
Print Name: Signature: