NEC SL1000 Installation guide

-Technical Training -
(System Installation)
Next Topaz

Part 1 : Hardware Installation

NEC Confidential
© NEC Corporation 2009
Page 3
Important Notice
To avoid shock or damage, do not plug in or turn the system on before completing the
installation process. <No Power-ON Maintenance>
Avoid working with the KSU during electrical storms.
Use only commercial AC Power to prevent shock or fire.
Use the power cord supplied for the KSU.
Do NOT bundle AC Power cords together, the cords may over heat.
Make sure the KSU has proper Earth Ground.
The system should be “Wall-Mounting” only.
A dedicated 110/240VAC circuit located within 2 meters of the KSU is required. A
separate AC outlet is necessary for each KSU.
Meeting established environmental standards maximizes the life of the system.
Be sure the site is NOT :
In direct sunlight or in hot, cold or humid places.
In dusty areas or in areas where sulfuric gases are produced.
In places where shocks or vibrations are frequent or strong.
In places where water or other fluids comes in contact with the equipment.
In areas near high-frequency machines or electric welders.
Near computers, telexes, microwaves, air conditioners, etc.
Near radio antennas (including short-wave)
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 4
Wall Mounting (1)
The Main KSU (1632M-A)and Expansion KSU s (1632ME-A)must be mounted
onto the wall. Before installing, secure appropriate spacing as below.
KSU Wall Mounting (arrange lengthways)
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 5
Wall Mounting (2)
KSU Wall Mounting (arrange sideways)
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 6
Appendix : Notice for No.4 KSU
Any trunk (Analog, ISDN BRI/PRI) does NOT work.
Power Failure circuits are not available because of no trunks support.
Multi-Line Terminals, SLTs and DSS Consoles work but Door phone and Relay do NOT work.
Due to the cable length limitation, installation position of No.4 KSU must be careful.
No.4 KSU (No.3 Expansion KSU) has following limitations.
Main KSU
(1632M KSU)
No.1 Exp KSU
(1632ME KSU)
No.2 Exp KSU
(1632ME KSU)
No.3 Exp KSU
(1632ME KSU)
Cable length is
not enough!!
Main KSU
(1632M KSU)
No.1 Exp KSU
(1632ME KSU)
No.2 Exp KSU
(1632ME KSU)
No.3 Exp KSU
(1632ME KSU)
Expansion cable is special design and can NOT be extended by yourself to avoid any transmission error.
Newly
added
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 7
Grounding
•The “ETH” lug is located near Power supply unit on each KSU.
•Connect “ ETH” lug to the verified Earth Ground point by using 14AWG (2.0mm) wire.
KSU Grounding
Grounding must be done each KSU respectively.
Grounding is required not only for system protection
but also for Caller-ID detection.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 8
Power Failure Transfer
•SLT is connected to the Extension Port No. 8/16/24/32.
•Change the switch position of “J6” from “KT” to “PF”. (Default : KT)
Connected extension must be SLT.
Trunk Port Ext. Port
No. 1No. 8
No. 4No. 16
No. 7No. 24
All terminals on Slot No.4must be Analog
Terminals.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 9
Cabling (1)
•Each I/F card provides “RJ11” connectors.
•One “RJ11”connector is provided each Trunk and Extension port.
DO NOT wire the cable with an AC Cable, computer, etc.
DO NOT run the cable near the high frequency generating device.
Use cable protectors in case the cables are run on the floor.
Aerial distribution wiring is NOT allowed.
Trunks must be installed with Lightning Arresters.
T R
L H
T R
Modular Plug
Trunk Extension
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 10
Cabling (2)
Modular Cable
(4-wire, Straight)
T R
L H T R L H
Modular Cable
(2-wire, Straight)
Key Telephone DSS Console SLT
Key TEL / DSS Console wiring have “Polarity”.
SLT wiring does not have “Polarity”.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 11
Cable Length
Max 1125 m (0.5mm) <20mA>
Max 300 m (0.5mm)
Max 100 m (Ethernet Cable)
KTS
DSS
SLT
Door phone
ISDN
Terminal
Max 150 m (0.5mm)
PC
Printer
LAN
1632M / 1632ME
408E / 008E
CPU
(IP4xx-CPU-A1)
BRIU Max 500 m (0.5mm) <P-P>
Max 100 / 300 m (0.5mm) <P-MP : Short / Long>
ISDN
Terminal
PRIU Max 50 m (0.5mm) <P-P>
PZ-IPLA Max 100 m (VoIP / Ethernet Cable) IP Terminal /
LAN
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 12
408E / 008E Installation
• 408E / 008E cards are installed in the 1632M / 1632ME KSU.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 13
Optional Items Installation (1)
•Either EXIFB-C1 card can be installed at 1632M KSU.
EXIFB-C1
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

Part 2 : System Start Up &
Programming

NEC Confidential
© NEC Corporation 2009
Page 15
Start Up (1)
There are 2 types of Data :
Main Software
Customer Data
• Pre-stored into the Memory located onto 1632M KSU.
•Can be upgraded from the CF (Compact Flash) Card which is inserted to
“CF Slot” at VM-21.
•Automatically be saved to the memory on 1632M KSU. Backed up by Lithium
Battery.
•Can be saved to the CF Card which is inserted to “CF Slot” at VM-21
•Can be saved to your PC by PC PRO software.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 16
System Start Up
Main software and “Default” data will be loaded. (System Initialization)
1. Keep pressing “Load” Button on CD-CP00 Blade.
2. AC Power switch ON.
3. Keep pressing “Load” Button about 3-4 sec.
4. Release “Load” Button.
5. Wait about 1-2 min.
There are 2 types of startup mode :
Main software and “Customer” data will be loaded. (System Reset)
1. AC Power Switch ON.
or
AC Power Switch OFF and ON.
COLD Start
HOT Start
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 17
Accessing Programming (1)
•Programming can be accessed 3 separate ways :
From Display type Desktop Terminal
Possible to set the data by following the manual.
Web Programming
Doesn’t need special application because the application is built into
CPU (IP4xx-CPU-A1) . Just standards Web browser is necessary, and on-line
programming is available.
PC Programming
The special application which is provided by NEC-i should be installed on the
PC that will be used for PC PRO. Doesn’t need real DRACO system, off-line
programming is also available, and the customer data can be saved on the PC.
•3 default passwords/Levels are built into the System. (IN / SA / SB)
•The “IN (Installer)” Level has full access to all programs.
•The “SA / SB (System Admin)” Levels have limited access.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 18
Combination
Example Desktop Terminal Web PRO PC PRO Total
No.1 2 users 2 users 04 users
No.2 04 users 04 users
No.3 0 0 1 user 1 user
Accessing Programming (2)
•Following number of users can enter the Programming Mode at the same time.
From Desktop Terminal : Up to 2 users
From Web PRO : Up to 4 users
From PCPRO : Up to 1 user
•“Auto Log-Out” is available in case nobody operates during pre-programmed
period on the Programming from Desktop Terminal and Web PRO. This period
is programmable by PRG20-01-12 (Default : 900 sec)
In case of PCPRO, only 1
user can enter the PRG
Mode at the same time.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 19
Accessing Programming
•Programming can be accessed 2 separate ways :
From Display Key Telephone
Possible to set the data by following the manual.
PC Programming
The special application which is provided by NEC-i should be installed on the
PC that will be used for PC PRO. Doesn’t need real Topaz system, off-line
programming is also available, and the customer data can be saved.
•3 default passwords/Levels are built into the System. (IN / SA / SB)
•The “IN (Installer)” Level has full access to all programs.
•The “SA / SB (System Admin)” Levels have limited access.
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]

NEC Confidential
© NEC Corporation 2009
Page 20
Enter / Exit Programming Mode
<To Enter>
1.Press SPK Key.
2. Dial #, *, #, *.
3. Dial Password.
4. Press HOLD Key.
<To Exit>
1.Return to PRG No. entering screen
by pressing DC Key.
2. Press SPK Key.
3. Return to normal mode. (Time&Date)
Procedure on Display Key Telephone (2 of any ports) (PRG mode)
Normal Mode PRG No. Entering screen
Key Description
0-9, * and #Enter data into a Program
HOLD Complete the programming (ENTER Key)
DND Switch the cursor between 1st and 2nd Display
Mute Exit one step at a time (ESC Key)
บริษัท โปรเฟสชั�นแนล พีเอบีเอ็กซ์ จํากัด โทร. 02-519-1718 Hotline. [phone]