NEC SL1000 Owner's manual

Programming Manual
A50-031167-002 EU
ISSUE 1.0
May 2011

Copyright
NEC Corporation reserves the right to change the specifications, functions, or features at any time
without notice.
NEC Corporation has prepared this document for use by its employees and customers. The informa-
tion contained herein is the property of NEC Corporation and shall not be reproduced without prior writ-
ten approval of NEC Corporation.
Windows is a registered trademark of Microsoft Corporation.
Copyright 2011
NEC Corporation
Printed in Japan

Chapter 1 Introduction
Section 1 BEFORE YOU START PROGRAMMING .................................................... 1-1
Section 2 HOW TO USE THIS MANUAL .................................................................1-1
Section 3 HOW TO ENTER PROGRAMMING MODE ..................................................1-2
Section 4 HOW TO EXIT PROGRAMMING MODE .....................................................1-3
Section 5 USING KEYS TO MOVE AROUND IN THE PROGRAMS .................................1-4
Section 6 PROGRAMMING NAMES AND TEXT MESSAGES ........................................1-5
Section 7 USING SOFTKEYS FOR PROGRAMMING ................................................. 1-6
Section 8 WHAT THE SOFTKEY DISPLAY PROMPTS MEAN .......................................1-6
Section 9 SYSTEM NUMBER PLAN/CAPACITIES ..................................................... 1-7
Section 10 CONCEPT OF SLOT NUMBER .............................................................1-10
Chapter 2 Programming the SL1000/SL1100
Section 1 PROGRAMMING YOUR SYSTEM ............................................................ 2-1
Program 10 : System Configuration Setup
10-01 : Time and Date ................................................................................ 2-3
10-02 : Location Setup ............................................................................... 2-4
10-03 : ETU Setup .................................................................................... 2-5
10-04 : Music On Hold Setup .......................................................................2-12
10-06 : ISDN BRI Setup .............................................................................2-13
10-07 : Conversation Recording Resource ......................................................2-14
10-08 : Pre-Ringing Setup ..........................................................................2-15
10-09 : DTMF and Dial Tone Circuit Setup .......................................................2-16
10-12 : CPU Network Setup ........................................................................2-17
10-13 : In-DHCP Server Setup .....................................................................2-19
10-14 : Managed Network Setup ..................................................................2-20
10-15 : Client Information Setup ...................................................................2-21
10-16 : Option Information Setup ..................................................................2-22
10-17 : H.323 Gatekeeper Setup ..................................................................2-25
10-18 : H.323 Alias Address Setup ................................................................2-26
10-19 : VoIPDB DSP Resource Selection ........................................................2-27
10-20 : LAN Setup for External Equipment .......................................................2-28
10-23 : SIP System Interconnection Setup .......................................................2-29
10-24 : Daylight Savings Setup ....................................................................2-30
10-25 : H.323 Gateway Prefix Setup ..............................................................2-31
10-26 : IP System Operation Setup ...............................................................2-32
10-28 : SIP System Information Setup ............................................................2-33
10-29 : SIP Server Information Setup .............................................................2-34
10-30 : SIP Authentication Information Setup ....................................................2-36
10-33 : SIP Registrar/Proxy Information Basic Setup ...........................................2-37
10-36 : SIP Trunk Registration Information Setup ...............................................2-38
10-37 : UPnP Setup .................................................................................2-39
10-39 : Fractional Setup ............................................................................2-40
10-40 : IP Trunk Availability .........................................................................2-41
10-42 : Virtual Loop Back Port Setting ............................................................2-42
10-45 : IP Routing Table Setup ....................................................................2-44
10-46 : DR700 Server Information Setup .........................................................2-44
10-48 : License Activation ..........................................................................2-46
10-49 : License File Activation .....................................................................2-47
10-50 : License Information ........................................................................2-48
10-51 : PRI/T1/E1 Selection of PRI ...............................................................2-49
10-52 : Free/Demo License Information ..........................................................2-50
10-60 : Audio Port Setup (SL1100) ................................................................2-51
TABLE OF CONTENTS
Programming Manual i

10-61 : Relay Port Setup ............................................................................2-54
10-62 : NetBIOS Setting ............................................................................2-54
10-63 : DHCP Client Setting ........................................................................2-54
Program 11 : System Numbering
11-01 : System Numbering .........................................................................2-55
11-02 : Extension Numbering ......................................................................2-61
11-04 : Virtual Extension Numbering ..............................................................2-62
11-07 : Department Group Pilot Numbers ........................................................2-63
11-09 : Trunk Access Code .........................................................................2-64
11-10 : Service Code Setup (for System Administrator) ........................................2-65
11-11 : Service Code Setup (for Setup/Entry Operation) .......................................2-68
11-12 : Service Code Setup (for Service Access) ...............................................2-71
11-14 : Service Code Setup (for Hotel) ...........................................................2-74
11-15 : Service Code Setup, Administrative (for Special Access) .............................2-76
11-16 : Single Digit Service Code Setup ..........................................................2-77
11-19 : Remote Conference Pilot Number Setup ................................................2-78
11-20 : Dial Extension Analyze Table .............................................................2-79
Program 12 : Night Mode Setup
12-01 : Night Mode Function Setup ...............................................................2-80
12-02 : Automatic Night Service Patterns ........................................................2-81
12-03 : Weekly Night Service Switching ..........................................................2-83
12-04 : Holiday Night Service Switching ..........................................................2-84
12-05 : Night Mode Group Assignment for Extensions .........................................2-85
12-06 : Night Mode Group Assignment for Trunks ..............................................2-86
12-07 : Text Data for Night Mode ..................................................................2-87
12-08 : Night Mode Service Range ................................................................2-88
Program 13 : Abbreviated Dialing
13-01 : Speed Dialing Option Setup ...............................................................2-89
13-02 : Group Speed Dialing Bins .................................................................2-90
13-03 : Speed Dialing Group Assignment for Extensions ......................................2-91
13-04 : Speed Dialing Number and Name .......................................................2-92
13-05 : Speed Dial Trunk Group ...................................................................2-94
13-06 : Speed Dial Number and Name ...........................................................2-95
13-11 : Abbreviated Dial Group Name ............................................................2-96
Program 14 : Trunk, Basic Setup
14-01 : Basic Trunk Data Setup ....................................................................2-97
14-02 : Analog Trunk Data Setup ................................................................ 2-101
14-04 : Behind PBX Setup ........................................................................ 2-104
14-05 : Trunk Group ................................................................................2-105
14-06 : Trunk Group Routing ..................................................................... 2-106
14-07 : Trunk Access Map Setup ................................................................ 2-108
14-08 : Music on Hold Source for Trunks ....................................................... 2-110
14-09 : Conversation Recording Destination for Trunks .......................................2-111
14-11 : ID Setup for IP Trunk ......................................................................2-112
14-12 : SIP Register ID Setup for IP Trunk ..................................................... 2-113
14-15 : ISDN Call Forward Method ...............................................................2-114
14-16 : ISDN Call Transfer Method ...............................................................2-115
Program 15 : Extension, Basic Setup
15-01 : Basic Extension Data Setup .............................................................2-116
15-02 : Multiline Telephone Basic Data Setup ..................................................2-118
15-03 : Single Line Telephone Basic Data Setup .............................................. 2-124
15-05 : IP Telephone Terminal Basic Data Setup .............................................. 2-127
15-06 : Trunk Access Map for Extensions ...................................................... 2-130
15-07 : Programmable Function Keys .......................................................... 2-131
15-08 : Incoming Virtual Extension Ring Tone Setup ......................................... 2-139
TABLE OF CONTENTS
Programming Manualii

15-09 : Virtual Extension Ring Assignment ..................................................... 2-140
15-10 : Incoming Virtual Extension Ring Tone Order Setup ................................. 2-141
15-11 : Virtual Extension Delayed Ring Assignment .......................................... 2-142
15-12 : Conversation Recording Destination for Extensions ................................ 2-143
15-13 : Loop Keys ..................................................................................2-144
15-14 : Programmable One-Touch Keys (SL1100) ............................................ 2-145
15-16 : SIP Register ID Setup for Extension ................................................... 2-146
15-17 : CO Message Waiting Indication ........................................................ 2-147
15-18 : Virtual Extension Key Enhanced Options ............................................. 2-148
15-22 : Mobile Extension Setup .................................................................. 2-149
Program 16 : Department Group Setup
16-01 : Department Group Basic Data Setup .................................................. 2-150
16-02 : Department Group Assignment for Extensions ....................................... 2-152
16-03 : Secondary Department Group .......................................................... 2-153
16-04 : Call Restriction Between Department Groups ........................................ 2-154
Program 20 : System Option Setup
20-01 : System Options ............................................................................2-155
20-02 : System Options for Multiline Telephones .............................................. 2-156
20-03 : System Options for Single Line Telephones .......................................... 2-159
20-04 : System Options for Virtual Extensions ................................................ 2-161
20-05 : System Options for Charging Cost Service ........................................... 2-162
20-06 : Class of Service for Extensions ......................................................... 2-163
20-07 : Class of Service Options (Administrator Level) ...................................... 2-164
20-08 : Class of Service Options (Outgoing Call Service) ................................... 2-166
20-09 : Class of Service Options (Incoming Call Service) ................................... 2-169
20-10 : Class of Service Options (Answer Service) ........................................... 2-171
20-11 : Class of Service Options (Hold/Transfer Service) .................................... 2-172
20-12 : Class of Service Options (Charging Cost Service) ................................... 2-175
20-13 : Class of Service Options (Supplementary Service) .................................. 2-176
20-14 : Class of Service Options for DISA/E&M ............................................... 2-180
20-15 : Ring Cycle Setup ......................................................................... 2-182
20-16 : Selectable Display Messages ........................................................... 2-184
20-17 : Operator Extension ........................................................................2-186
20-18 : Service Tone Timers ...................................................................... 2-187
20-19 : System Options for Caller ID ............................................................ 2-188
20-20 : Message Setup for Non-Caller ID Data ................................................ 2-189
20-21 : System Options for Long Conversation ............................................... 2-190
20-23 : System Options for CTI .................................................................. 2-191
20-25 : ISDN Options ...............................................................................2-192
20-26 : Multiplier for Charging Cost ............................................................. 2-194
20-28 : Trunk to Trunk Conversation ............................................................ 2-195
20-29 : Timer Class for Extension ............................................................... 2-196
20-30 : Timer Class for Trunks ................................................................... 2-197
20-31 : Timer Class Timer Assignment ......................................................... 2-198
20-34 : Remote Conference Group Setup ...................................................... 2-201
20-35 : Extension's Operator Setting ............................................................ 2-202
20-36 : Trunk's Operator Setting ................................................................. 2-203
20-37 : Operator Extension Group Setup ...................................................... 2-204
20-38 : Operator Group Setting .................................................................. 2-205
20-39 : Shortcut Operation Setup (SL1000) ................................................... 2-206
20-40 : Function Key List Setup (SL1000) ..................................................... 2-207
20-41 : Service Code Setup (SL1000) .......................................................... 2-208
20-42 : Night Mode for each package ........................................................... 2-209
20-43 : Power supply for each package ........................................................ 2-210
20-44 : Watch Mode Setup ........................................................................2-211
TABLE OF CONTENTS
Programming Manual iii

20-45 : Remote Watch Setup .................................................................... 2-212
20-46 : Security Sensor Setup ................................................................... 2-213
20-47 : Time pattern setting for Watch Mode .................................................. 2-214
20-48 : Time pattern setting for Security Sensor .............................................. 2-215
20-49 : Caller ID Shared Group Basic Data Setup ............................................ 2-216
Program 21 : Outgoing Call Setup
21-01 : System Options for Outgoing Calls .................................................... 2-217
21-02 : Trunk Group Routing for Extensions ................................................... 2-220
21-03 : Trunk Group Routing for Trunks ........................................................ 2-221
21-04 : Toll Restriction Class for Extensions ................................................... 2-222
21-05 : Toll Restriction Class ..................................................................... 2-223
21-06 : Toll Restriction Table Data Setup ....................................................... 2-225
21-07 : Toll Restriction Override Password Setup ............................................. 2-227
21-08 : Repeat Dial Setup ........................................................................ 2-228
21-09 : Dial Block Setup .......................................................................... 2-229
21-10 : Dial Block Restriction Class Per Extension ........................................... 2-230
21-11 : Extension Ringdown (Hotline) Assignment ............................................ 2-231
21-12 : ISDN Calling Party Number Setup for Trunks ........................................ 2-232
21-13 : ISDN Calling Party Number Setup for Extensions ................................... 2-233
21-14 : Walking Toll Restriction Password Setup .............................................. 2-234
21-15 : Individual Trunk Group Routing for Extensions ....................................... 2-235
21-17 : IP Trunk (SIP) Calling Party Number Setup for Trunk ...............................2-236
21-18 : IP Trunk (H.323) Calling Party Number Setup for Extension .......................2-237
21-19 : IP Trunk (SIP) Calling Party Number Setup for Extension ..........................2-238
21-20 : SIP Trunk Call Discernment Setup for Extension .................................... 2-239
21-21 : Toll Restriction for Trunks (Seized Trunk Basis Setting) .............................2-240
21-22 : CO Message Waiting Indication - Call Back Settings ................................ 2-241
21-24 : Forced Access Dial Data ................................................................ 2-242
Program 22 : Incoming Call Setup
22-01 : System Options for Incoming Calls .................................................... 2-243
22-02 : Incoming Call Trunk Setup .............................................................. 2-245
22-03 : Trunk Ring Tone Range .................................................................. 2-246
22-04 : Incoming Extension Ring Group Assignment ......................................... 2-248
22-05 : Incoming Trunk Ring Group Assignment .............................................. 2-249
22-06 : Normal Incoming Ring Mode ............................................................ 2-250
22-07 : DIL Assignment ............................................................................2-251
22-08 : DIL/IRG No Answer Destination ........................................................ 2-252
22-09 : DID Basic Data Setup .................................................................... 2-253
22-10 : DID Translation Table Setup ............................................................ 2-254
22-11 : DID Translation Number Conversion ................................................... 2-255
22-12 : DID Intercept Ring Group ............................................................... 2-258
22-13 : DID Trunk Group to Translation Table Assignment .................................. 2-259
22-14 : VRS Delayed Message for IRG ......................................................... 2-260
22-15 : VRS Delayed Message for Department Group ....................................... 2-261
22-16 : Private Call Refuse Target Area Setup ................................................ 2-262
22-17 : Dial-In Conversion Table Area Setup for Time Pattern ..............................2-263
22-18 : Private Call Assignment Setup .......................................................... 2-264
22-19 : DID MFC Dialing Options ................................................................ 2-265
22-20 : Flexible Ringing by Caller ID Setup .................................................... 2-266
Program 23 : Answer Features Setup
23-02 : Call Pickup Groups ....................................................................... 2-267
23-03 : Universal Answer/Auto Answer ......................................................... 2-268
23-04 : Ringing Line Preference for Virtual Extensions ...................................... 2-269
TABLE OF CONTENTS
Programming Manualiv

Program 24 : Hold/Transfer Setup
24-01 : System Options for Hold ................................................................. 2-270
24-02 : System Options for Transfer ............................................................ 2-271
24-03 : Park Group .................................................................................2-273
24-04 : Automatic Trunk-to-Trunk Transfer Target Setup ..................................... 2-274
24-05 : Department Group Transfer Target Setup ............................................. 2-275
24-09 : Call Forward Split Settings .............................................................. 2-276
Program 25 : VRS/DISA Setup
25-01 : VRS/DISA Line Basic Data Setup ...................................................... 2-278
25-02 : DID/DISA VRS Message ................................................................ 2-279
25-03 : VRS/DISA Transfer Ring Group With Incorrect Dialing ............................. 2-280
25-04 : VRS/DISA Transfer Ring Group With No Answer/Busy ............................. 2-281
25-05 : VRS/DISA Error Message Assignment ................................................ 2-282
25-06 : VRS/DISA One-Digit Code Attendant Setup .......................................... 2-283
25-07 : System Timers for VRS/DISA ........................................................... 2-284
25-08 : DISA User ID Setup ...................................................................... 2-286
25-09 : Class of Service for DISA Users ........................................................ 2-287
25-10 : Trunk Group Routing for DISA .......................................................... 2-288
25-11 : DISA Toll Restriction Class .............................................................. 2-289
25-12 : Alternate Trunk Group Routing for DISA .............................................. 2-290
25-13 : System Option for DISA ................................................................. 2-291
25-15 : DISA Transfer Target Setup ............................................................. 2-292
Program 26 : ARS Service & Least Cost Routing
26-01 : Automatic Route Selection (ARS/F-Route) Service ................................. 2-293
26-02 : Dial Analysis Table for ARS/LCR ....................................................... 2-294
26-03 : ARS Dial Treatments ..................................................................... 2-295
26-04 : ARS Class of Service .................................................................... 2-296
26-05 : LCR Carrier Table ........................................................................ 2-297
26-06 : LCR Authorization Code Table .......................................................... 2-298
26-07 : LCR Cost Center Code Table ........................................................... 2-299
26-08 : LCR Manual Override Access Code Table ............................................ 2-300
26-09 : LCR Manual Override Exemption Table ............................................... 2-301
26-11 : Transit Network ID Table ................................................................. 2-302
26-12 : Network Specific Parameter Table for ARS ........................................... 2-303
Program 30 : DSS/DLS Console Setup
30-01 : DSS Console Operating Mode .......................................................... 2-304
30-02 : DSS Console Extension Assignment .................................................. 2-305
30-03 : DSS Console Key Assignment .......................................................... 2-306
30-04 : DSS Console Alternate Answer (SL1100) ............................................. 2-312
30-05 : DSS Console Lamp Table ............................................................... 2-313
Program 31 : Paging Setup
31-01 : System Options for Internal/External Paging ......................................... 2-316
31-02 : Internal Paging Group Assignment ..................................................... 2-318
31-03 : Internal Paging Group Settings ......................................................... 2-319
31-04 : External Paging Zone Group ............................................................ 2-321
31-05 : Universal Night Answer/Ring Over Page .............................................. 2-322
31-06 : External Speaker Control ................................................................ 2-323
31-07 : Combined Paging Assignments ........................................................ 2-324
31-08 : BGM on External Paging ................................................................ 2-325
31-10 : External Paging Group Basic Setting .................................................. 2-326
Program 32 : Door Box and Sensor Setup
32-01 : Door Box Timers Setup .................................................................. 2-327
32-02 : Door Box Ring Assignment .............................................................. 2-328
32-03 : Door Box Basic Setup .................................................................... 2-329
32-04 : Door Box Name Setup ................................................................... 2-330
TABLE OF CONTENTS
Programming Manual v

Program 34 : Tie Line Setup
34-01 : E&M Tie Line Basic Setup ............................................................... 2-331
34-02 : E&M Tie Line Class of Service .......................................................... 2-332
34-03 : Trunk Group Routing for E&M Tie Lines ............................................... 2-333
34-04 : E&M Tie Line Toll Restriction Class .................................................... 2-334
34-05 : Tie Line Outgoing Call Restriction ...................................................... 2-335
34-06 : Add/Delete Digit for E&M Tie Line ...................................................... 2-336
34-07 : E&M Tie Line Timer ....................................................................... 2-337
34-08 : Toll Restriction Data for E&M Tie Lines ................................................ 2-338
34-09 : ANI/DNIS Service Options .............................................................. 2-339
34-11 : E1 Trunk Basic Setup .................................................................... 2-342
Program 35 : SMDR Account Code Setup
35-01 : SMDR Options .............................................................................2-343
35-02 : SMDR Output Options ................................................................... 2-344
35-03 : SMDR Port Assignment for Trunk Group .............................................. 2-347
35-04 : SMDR Port Assignment for Department Groups ..................................... 2-348
35-05 : Account Code Setup ..................................................................... 2-349
35-06 : Verified Account Code Table ............................................................ 2-350
Program 40 : Voice Recording System
40-01 : Voice Mail Basic Setup ................................................................... 2-351
40-07 : Voice Prompt Language Assignment for VRS ........................................ 2-352
40-10 : Voice Announcement Service Option .................................................. 2-353
40-11 : Preamble Message Assignment ........................................................ 2-355
Program 42 : Hotel Setup
42-01 : System Options for Hotel/Motel ........................................................ 2-356
42-02 : Hotel/Motel Telephone Setup ........................................................... 2-357
42-03 : Class of Service Options (Hotel/Motel) ................................................ 2-358
42-04 : Hotel Mode One-Digit Service Codes ................................................. 2-359
42-05 : Hotel Room Status Printer ............................................................... 2-360
42-08 : Text Message Setup for Hotel Room Status .......................................... 2-361
Program 44 : ARS/F-Route Setup
44-01 : System Options for ARS/F-Route ...................................................... 2-363
44-02 : Dial Analysis Table for ARS/F-Route Access ......................................... 2-364
44-03 : Dial Analysis Extension Table ........................................................... 2-366
44-04 : ARS/F-Route Selection for Time Schedule ........................................... 2-367
44-05 : ARS/F-Route Table ........................................................................2-368
44-06 : Additional Dial Table ...................................................................... 2-370
44-07 : Gain Table for ARS/F-Route Access ................................................... 2-371
44-08 : Time Schedule for ARS/F-Route ....................................................... 2-372
44-09 : Weekly Schedule for ARS/F-Route .................................................... 2-373
44-10 : Holiday Schedule for ARS/F-Route .................................................... 2-374
Program 45 : Voice Mail Integration
45-01 : Voice Mail Integration Options .......................................................... 2-375
45-02 : NSL Option Setup ........................................................................ 2-377
45-04 : Voice Mail Digit Add Assignment ....................................................... 2-378
45-05 : Voice Mail Send Protocol Signal Without Additional Digits .........................2-379
Program 47 : InMail
47-01 : InMail System Options ................................................................... 2-380
47-02 : InMail Station Mailbox Options ......................................................... 2-384
47-03 : InMail Group Mailbox Options .......................................................... 2-388
47-06 : Group Mailbox Subscriber Options .................................................... 2-389
47-07 : InMail Routing Mailbox Options ........................................................ 2-393
47-08 : Call Routing Mailbox Options ........................................................... 2-395
47-09 : Announcement Mailbox Options ........................................................ 2-397
47-10 : InMail Trunk Options ..................................................................... 2-398
TABLE OF CONTENTS
Programming Manualvi

47-11 : InMail Answer Table Options ............................................................ 2-400
47-12 : InMail Answer Schedules ................................................................ 2-404
47-13 : InMail Dial Action Tables ................................................................. 2-408
47-15 : Routing Directory Mailbox Options ......................................................2-411
47-17 : Routing Distribution Mailbox Options .................................................. 2-412
47-18 : InMail SMTP Setup ....................................................................... 2-413
47-19 : InMail POP3 Setup ....................................................................... 2-414
47-20 : Station Mailbox Message Notification Options ....................................... 2-415
47-21 : Station Mailbox Find-Me Follow-Me Options ......................................... 2-416
47-22 : Group Mailbox Message Notification Options ........................................ 2-417
47-23 : Group Mailbox Find-Me Follow-Me Options .......................................... 2-418
Program 80 : Basic Hardware Setup for System
80-01 : Service Tone Setup ....................................................................... 2-419
80-02 : DTMF Tone Setup ........................................................................ 2-424
80-03 : DTMF Tone Receiver Setup ............................................................. 2-425
80-04 : Call Progress Tone Detector Setup .................................................... 2-427
80-05 : Date Format for SMDR and System ................................................... 2-429
80-06 : Reference Impedance Setup ........................................................... 2-430
80-07 : Call Progress Tone Detector Frequency Setup ....................................... 2-431
80-08 : MFC Tone Setup .......................................................................... 2-432
80-09 : Short Ring Setup ......................................................................... 2-433
80-11 : MFC Tone Receiver Setup ............................................................... 2-435
80-12 : Caller ID Receiver Setup ................................................................ 2-437
Program 81 : Basic Hardware Setup for Trunk
81-01 : CO Initial Data Setup ..................................................................... 2-438
81-04 : ISDN BRI Layer 1 (T-Point) Initial Data Setup ........................................ 2-440
81-05 : ISDN BRI & PRI Layer 2 (T-Point) Initial Data Setup ................................2-441
81-06 : ISDN BRI & PRI Layer 3 (T-Point) Timer Setup ......................................2-442
81-07 : CODEC Filter Setup for Analog Trunk Port ........................................... 2-444
81-08 : T1 Trunk Timer Setup .................................................................... 2-445
81-09 : COT CODEC (QSLAC) Filter Setting .................................................. 2-448
81-13 : E1 Trunk Timer Setup .................................................................... 2-450
Program 82 : Basic Hardware Setup for Extension
82-01 : Incoming Ring Tone ...................................................................... 2-452
82-02 : Key Telephone LED Pattern Setup (SL1000) ......................................... 2-454
82-04 : ASTU Initial Data Setup .................................................................. 2-456
82-05 : ISDN BRI & PRI Layer2 (S-Point) Initial Data Setup .................................2-457
82-06 : ISDN BRI & PRI Layer3 (S-point) Timer Setup ....................................... 2-458
82-07 : CODEC Filter Setup for Analog Station Port .......................................... 2-459
82-08 : Sidetone Volume Setup .................................................................. 2-460
82-09 : SLIU CODEC Filter Data Setup ........................................................ 2-461
82-13 : Volume Level Data Setup for TXD TEL2 [LKTS] (SL1000) .........................2-463
82-14 : Handset/Headset Gain Setup for Multi Line Telephone ............................. 2-464
82-18 : KST CODEC Filter Data Setup (SL1000) ............................................. 2-465
82-19 : KST CODEC Filter Data Setup (SL1000) ............................................. 2-466
82-20 : Volume level Data Setup for KST (SL1000) ..........................................2-468
82-21 : Sensor Setup ...............................................................................2-469
Program 84 : Hardware Setup for VoIPDB
84-01 : H.323 Trunk Basic Information Setup .................................................. 2-470
84-02 : H.225 and H.245 Information Basic Setup ............................................ 2-472
84-07 : Firmware Download Setup .............................................................. 2-474
84-09 : VLAN Setup ................................................................................2-475
84-10 : ToS Setup ...................................................................................2-476
84-13 : SIP Trunk CODEC Information Basic Setup .......................................... 2-477
84-14 : SIP Trunk Basic Information Setup ..................................................... 2-480
TABLE OF CONTENTS
Programming Manual vii

84-15 : H.323/SIP Phone Keep Alive Setup .................................................... 2-481
84-16 : VoIPDB Limiter Control Gain Setup .................................................... 2-482
84-19 : SIP Extension CODEC Information Basic Setup ..................................... 2-483
84-20 : SIP Extension Basic Information Setup ............................................... 2-486
84-22 : DR700 Multiline Logon Information Setup ............................................ 2-487
84-23 : DR700 Multiline Basic Information Setup ............................................. 2-488
84-24 : DR700 Multiline CODEC Basic Information Setup ................................... 2-490
84-26 : VoIP Basic Setup (DSP) ................................................................. 2-493
84-27 : VoIP Basic Setup ......................................................................... 2-494
84-28 : DR700 Multiline Firmware Name Setup ............................................... 2-496
84-29 : SIP-MLT CODEC Information Fixed Mode Setup .................................... 2-497
84-31 : VoIPDB Echo Canceller Setup .......................................................... 2-498
Program 90 : Maintenance Program
90-01 : Installation Date ............................................................................2-501
90-02 : Programming Password Setup ......................................................... 2-502
90-03 : Save Data ...................................................................................2-504
90-04 : Load Data ...................................................................................2-505
90-05 : Slot Control .................................................................................2-506
90-06 : Trunk Control ...............................................................................2-507
90-07 : Station Control .............................................................................2-508
90-08 : System Reset ..............................................................................2-509
90-09 : Automatic System Reset Time Setup .................................................. 2-510
90-10 : System Alarm Setup .......................................................................2-511
90-11 : System Alarm Report ..................................................................... 2-517
90-12 : System Alarm Output .................................................................... 2-518
90-13 : System Information Output .............................................................. 2-519
90-16 : Main Software Information .............................................................. 2-520
90-17 : Firmware Information .....................................................................2-521
90-19 : Dial Block Release ....................................................................... 2-522
90-20 : Traffic Report Data Setup ................................................................ 2-523
90-21 : Traffic Report Output ..................................................................... 2-524
90-23 : Deleting Registration of IP Telephones ................................................ 2-525
90-24 : System Alarm Report Notification Time Setup ........................................ 2-526
90-25 : System Alarm Report CC Mail Setup .................................................. 2-527
90-26 : Program Access Level Setup ........................................................... 2-528
90-28 : User Programming Password Setup ................................................... 2-529
90-31 : DIM Access over Ethernet ............................................................... 2-530
90-33 : Preselected Data Setup ................................................................. 2-531
90-34 : Firmware Information .....................................................................2-549
90-35 : Wizard Programming Level Setup ..................................................... 2-550
90-36 : Firmware Update Time Setting ......................................................... 2-551
90-38 : User Programming Data Level Setup .................................................. 2-552
90-39 : Virtual Loop Back Port Reset ........................................................... 2-555
90-41 : Server Setting to Update Terminal Local Data ........................................ 2-556
90-42 : DR700 Multiline Terminal Version Information ........................................ 2-557
90-43 : Deleting Terminal License of DR700 ................................................... 2-558
90-44 : Deleting Terminal License of TCP Interface ........................................... 2-559
90-45 : Temporary Password Change for Multiline Telephone .............................. 2-560
90-50 : System Alarm Display Setup ............................................................ 2-561
90-51 : Alarm Setup for Maintenance Exchange .............................................. 2-562
90-52 : System Alarm Save ...................................................................... 2-563
90-53 : System Alarm Clear ...................................................................... 2-564
90-54 : PC/Web Programming ....................................................................2-565
90-55 : Free License Select ...................................................................... 2-566
90-56 : NTP Setup ..................................................................................2-567
TABLE OF CONTENTS
Programming Manualviii

90-57 : Backup Recovery Data .................................................................. 2-568
90-58 : Restore Recovery Data .................................................................. 2-569
90-59 : Delete Recovery Data .................................................................... 2-570
90-60 : T1/ISDN Layer Status Information ..................................................... 2-571
90-63 : DR700 Control .............................................................................2-572
90-65 : 1st Party CTI Authentication Password Setup ........................................ 2-573
90-66 : FTP Firmware Update setup ............................................................ 2-574
90-67 : Backup Data Auto-save Interval Time Set ............................................. 2-576
90-68 : Side Tone Auto Setup .................................................................... 2-576
Program 92 : Copy Program
92-01 : Copy Program ..............................................................................2-577
92-02 : Delete All Extension Numbers .......................................................... 2-580
92-03 : Copy Program by Port Number ......................................................... 2-581
92-04 : Extension Data Swap .................................................................... 2-582
92-05 : Extension Data Swap Password ....................................................... 2-584
92-06 : Fill Command ..............................................................................2-585
92-07 : Delete Command ..........................................................................2-586
TABLE OF CONTENTS
Programming Manual ix

Table 1-1 Keys for Entering Data (SL1000) .............................................................. 1-4
Table 1-2 Keys for Entering Data (SL1100) ..............................................................1-5
Table 1-3 Keys for Entering Names ....................................................................... 1-5
Table 1-4 Softkey Display Prompts ....................................................................... 1-7
Table 1-5 System Number Plan/Capacities .............................................................. 1-7
Table 2-1 System Numbering Default Settings .........................................................2-56
Table 2-2 Function Number List ........................................................................ 2-132
Table 2-3 Function Number List ........................................................................ 2-136
Table 2-4 Ringing Cycles .................................................................................2-182
Table 2-5 Program 22-03 - Incoming Signal Frequency Patterns (SL1000) ..................... 2-246
Table 2-6 Program 22-03 - Incoming Signal Frequency Patterns (SL1100) ......................2-246
Table 2-7 Function Number List .........................................................................2-306
Table 2-8 Function Number List .........................................................................2-310
Table 2-9 47-02-16 Default Table .......................................................................2-387
Table 2-10 47-06-14 Default Table ......................................................................2-391
Table 2-11 47-07-03 Default Table ......................................................................2-394
Table 2-12 47-10-03 Default Table ......................................................................2-399
Table 2-13 Basic Tones ...................................................................................2-419
Table 2-14 Frequency 1/2 Table .........................................................................2-433
Table 2-15 Ring Cycle Table .............................................................................2-433
Table 2-16 Default Table ..................................................................................2-434
Table 2-17 Default Table ..................................................................................2-435
Table 2-18 Description of Alarm .........................................................................2-511
LIST OF TABLES
Programming Manualx

SECTION 1 BEFORE YOU START PROGRAMMING
Before customizing your system be sure to read this chapter first.
This chapter provides you with detailed information about the system programs. By changing a pro-
gram, you change the way the feature associated with that program works. In this chapter, you find out
about each program, the features that the program affects and how to enter the program data into sys-
tem memory.
This Manual is created for System : SL1000/SL1100
SECTION 2 HOW TO USE THIS MANUAL
This section lists each program in numerical order. For example, Program 10-01 is at the beginning of
the section and Program 92-01 is at the end. The information on each program is subdivided into the
following headings :
Description describes what the program options control. The Default Settings for each program are
also included. When you first install the system, it uses the Default Setting for all programs. Along with
the Description are the Conditions which describe any limits or special considerations that may apply
to the program.
The program access level is just above the Description heading. You can only use the program if your
access level meets or exceeds the level the program requires. Refer to How to Enter Programming
Mode on the next page for a list of the system access levels and passwords.
Feature Cross Reference provides you with a table of all the features affected by the program. You
will want to keep the referenced features in mind when you change a program. Customizing a feature
may have an effect on another feature that you did not intend.
Telephone Programming Instructions shows how to enter the program data into system memory.
For example :
1Enter the programming mode.
Introduction 1
Introduction
Programming Manual 1-1

215-07-01
tells you to enter the programming mode, dial 150701 from the telephone dial pad. After you do, you
will see the message “15-07-01 TEL” on the first line of the telephone display. This indicates the pro-
gram number (15-07), item number (01), and that the options are being set for the extension. The sec-
ond row of the display “KY01 = *01” indicates that Key 01 is being programmed with the entry of *01.
The third row allows you to move the cursor to the left or right, depending on which arrow is pressed.
To learn how to enter the programming mode, refer to How to Enter Programming Mode on this page.
SECTION 3 HOW TO ENTER PROGRAMMING MODE
To enter programming mode :
1Go to any working display telephone.
In a newly installed system, use extension (port 1).
2Do not lift the handset.
3Press Speaker.
4#*#*.
5Dial the system password + Hold. Refer to the following table for the default system passwords. To
15-07-01 TEL200
KY01 = *01
(Multiline Telephone) (SL1000)
15-07-01 TEL
KY01 = *01
- +
(IP Phone) (SL1000)
15-07-01 TEL
KY01 = *01
- +
(SL1100)
ISSUE 1.0SL1000/SL1100
Introduction1-2

change the passwords, use 90-02 : Programming Password Setup on page 2-502.
Password User Name Level Programs at this Level
****** nec-i 1 (MF) Manufacture Level (MF) :
80-02, 81-04, 81-05, 82-02 (SL1000) , 82-05, 82-08 (SL1100)
12345678 tech 2 (IN) Installation (IN) :
All programs in this section not listed for MF, SA, & SB
0000 admin1 3 (SA)
System Administrator - Level 1 (SA) :
10-01, 10-02, 10-12, 10-13, 10-14, 10-15, 10-16, 10-17, 10-18, 10-23, 10-
24, 10-25, 10-28, 10-29, 10-45, 12-02, 12-03, 12-04, 12-08, 15-01, 15-07,
15-09, 15-10, 15-11, 20-16, 20-34, 21-07, 21-14, 22-04, 22-11, 22-17, 25-
08, 30-03, 30-04, 32-02, 45-02, 84-22, 90-03, 90-04, 90-06, 90-07, 90-19,
90-57, 90-58, 90-59, 90-65
9999 admin2 4 (SB) System Administrator - Level 2 (SB) :
13-04, 13-05, 13-06, 13-11, 15-14 (SL1100) , 21-20
SECTION 4 HOW TO EXIT PROGRAMMING MODE
To-exit the programming mode :
When you are done programming, you must be out of a program option to exit (pressing the Mute key
will exit the program option).
1Press Mute key to exit the program options, if needed.
2Press Speaker. If changes were to the system programming, "Saving System Data" is displayed.
3The display shows "Complete Data Save" when completed and exits the telephone to an idle
mode.
Program Mode
(SL1000)
Program Mode
Base Service OP1 OP2
(SL1100)
Program Mode
(SL1000)
Program Mode
Base Service OP1 OP2
(SL1100)
ISSUE 1.0 SL1000/SL1100
Programming Manual 1-3

To save a customer’s database, a blank Compact Flash (CF) Card is required. Insert the CF Card into the CPU
and, using Program 90-03, save the software to the CF Card. (Program 90-04 is used to reload the customer
data if necessary.) Note that a CF Card can only hold one customer database. Each database to be saved re-
quires a separate drive.
CF card
CF Slot (CN2)
CPU card
VMDB-C1
SECTION 5 USING KEYS TO MOVE AROUND IN THE
PROGRAMS
Once you enter the programming mode, use the keys in the following chart to enter data, edit data and
move around in the menus.
Table 1-1 Keys for Entering Data (SL1000)
When you want to ... Telephone Programming
Enter Data into program 0~9,*,#,LineKey(1~6)
Next Index Cursor Key (Up)
Prior Index Cursor Key (Down)
Select Data Line Key (1 ~ 6)
All Clear Flash
Register Hold
Enter
Go Back to Prior Screen Mute
Clear / Back
Move Cursor Jump Up/Down DND or DND / CONF
Delete single character Clear / Back
Next Page -
Toggle between Number/Character Help
While in a Entering Number
Prior Page -
Quit the programming Speaker
Exit
Move Cursor to Left Cursor Key (Left)
Change Program Number -
Change Index Number
ISSUE 1.0SL1000/SL1100
Introduction1-4

When you want to ... Telephone Programming
Change Program Number -
Change Index Number
Move Cursor to Right Cursor Key (Right)
Table 1-2 Keys for Entering Data (SL1100)
When you want to ... Telephone Programming
Enter Data into program 0~9,*,#LineKey(1~6)
Next Index Cursor Key (Up)
Prior Index Cursor Key (Down)
Select Data Line Key (1 ~ 6)
All Clear Flash
Register Hold
Enter
Go Back to Prior Screen Mute
Clear / Back
Move Cursor Jump Up/Down DND
Delete single character Clear / Back
Next Page Help
Toggle between Number/Character
While in a Entering Number
Prior Page Transfer
Quit the programming Speaker
Exit
Move Cursor to Left Cursor Key (Left)
Soft Key1
Change Program Number Soft Key2
Change Index Number
Change Program Number Soft Key3
Change Index Number
Move Cursor to Right Cursor Key (Right)
Soft Key4
SECTION 6 PROGRAMMING NAMES AND TEXT MESSAGES
Several programs (e.g., Program 20-16 : Selectable Display Messages) require you to enter text. Use
the following chart when entering and editing text. When using the keypad digits, press the key once
for the first character, twice for the second character, etc. For example, to enter a C, press the key 2
three times. Press the key six times to display the lower case letter. The name can be up to 12 digits
long.
Table 1-3 Keys for Entering Names
Use this keypad digit ... When you want to ...
1Enter characters : 1@[¥]^_`{|} ÁÀÂÃÅÆÇÉÊìó0
2Enter characters : A-C, a-c, 2.
ISSUE 1.0 SL1000/SL1100
Programming Manual 1-5

Use this keypad digit ... When you want to ...
3Enter characters : D-F, d-f, 3.
4Enter characters : G-I, g-i, 4.
5Enter characters : J-L, j-l, 5.
6Enter characters : M-O, m-o, 6.
7Enter characters : P-S, p-s, 7.
8Enter characters : T-V, t-v, 8.
9Enter characters : W-Z, w-z, 9.
0Enter characters : 0!“#$%&’()ôõúåäæöüαεθВ
*Enter characters : *+,-./:;<=>?πΣσΩ∞¢£
#
# = Accepts an entry (only required if two letters on the same key are needed - ex :
TOM). Pressing # again = Space. (In system programming mode, use the right arrow
Softkey instead to accept and/or add a space.)
Clear/Back Clear the character entry one character at a time.
Flash Clear all the entries from the point of the flashing cursor and to the right.
SECTION 7 USING SOFTKEYS FOR PROGRAMMING
(This Feature is available for IP Phone Only.) (SL1000)
Each Display telephone with Softkeys provides interactive Softkeys for intuitive feature access. The
options for these keys will automatically change depending on where you are in the system program-
ming. Simply press the Softkey located below the option you wish and the display will change accord-
ingly.
Pressing the Cursor key Up or Down will scroll between the menus.
SECTION 8 WHAT THE SOFTKEY DISPLAY PROMPTS MEAN
(This Feature is available for IP Phone Only.) (SL1000)
When using a display telephone in programming mode, various Softkey options are displayed. These
keys will allow you to easily select, scan, or move through the programs.
_
Program Mode
Base Service OP1 OP2
_
Program Mode
Hard Mtnance
ISSUE 1.0SL1000/SL1100
Introduction1-6

Table 1-4 Softkey Display Prompts
Softkey Display Prompts
If you press this Softkey
... The system will ...
back
Go back one step in the program display.
You can press Cursor Key (UP) or Cursor Key (Down) to scroll forward or backward through a
list of programs.
Scroll down through the available programs.
Scroll up through the available programs.
select Select the currently displayed program.
Move the cursor to the left.
Move the cursor to the right.
- 1 Move back through the available program options.
+ 1 Move forward through the available program options.
SECTION 9 SYSTEM NUMBER PLAN/CAPACITIES
The following table provides the capacities for the SL1000/SL1100 system.
Table 1-5 System Number Plan/Capacities
System Number Plan/Capacities
Note
System Type Number Plan/Capacities Related Pro-
gram
System
Analog Caller ID Detector (de-
tected by DSP) 132 (SL1000) 96 (SL1100) channels
Classes of Service 15 20–06
Day/Night Mode Numbers 8 12–07
Day/Night Service Patterns 4 12–07
Dial Tone Detector
DTMF Receiver
132 (SL1000)
96 (SL1100)
Toll Restriction Classes 15
Verifiable Account Code Table 800 35–06
Trunk
Trunk Port Number 126 (SL1000)
96 (SL1100)
Trunk Ports (Total) : 126 (SL1000)
• Analog Trunks 48 (SL1000)
• BRI Trunk Ports 36 (SL1000)
• T1/PRI Trunk Ports
(SL1000) 90 (SL1000)
• VoIPDB Trunk Ports
(VoIPDB & MEMDB is re-
quired. Need license to be
Max.)
16 (SL1000)
ISSUE 1.0 SL1000/SL1100
Programming Manual 1-7

System Number Plan/Capacities
Note
System Type Number Plan/Capacities Related Pro-
gram
• External Paging
(Use Analog Trunk ports) 3 (SL1000)
• External MOH
(Use Analog Trunk ports) 1 (SL1000)
• BGM Trunk Port
(Use Analog Trunk ports) 1 (SL1000)
Trunk Ports (Total) : 88 (SL1100)
• Analog Trunks 36 (SL1100)
• BRI Trunk Ports 36 (SL1100)
• T1/PRI Trunk Ports (SL1100) 60 (SL1100)
• VoIPDB Trunk Ports
(VoIPDB & MEMDB is re-
quired. Need license to be
Max.)
16 (SL1100)
DID Translation Tables 20 22–10
DID Translation Table Entries 800 22–10
DISA :
• Classes of Service
• Users
15
15
20–14
25–09
Ring Groups 25 22–04
Trunk Access Maps 126 (SL1000)
96 (SL1100) 14–07
Trunk Group Numbers 25 14–05
Trunk Routes 25 14–06
Extension
Telephone Extension Ports 128 (SL1000)
120 (SL1100)
• Multiline Terminals 96 (SL1000)
72 (SL1100)
• Single Line Phones/Analog
Devices
128 (SL1000)
60 (SL1100)
• VoIPDB Extensions (SIP-
MLT/Std)
(VoIPDB & MEMDB is re-
quired. Need license to be
Max. (SIP-Std))
32
Hybrid Extension Ports:
• Physical Ports 01 ~ 08 (SL1000)
Digital Extension Ports
• Physical Ports 01 ~ 08 (SL1100)
Telephone Extension Number
Range
1 ~ 8999*(SL1000)
1 ~ 89999999*(SL1100)
(*Extension cannot start with 0 or 9)
Virtual Extension Ports 50 11–04
Virtual Extension Number Range 1 ~ 8999*(SL1000)
1 ~ 89999999*(SL1100)
(*Extension cannot start with 0 or 9)
11–04
ISSUE 1.0SL1000/SL1100
Introduction1-8