NEC DS2000 IntraMail User manual

DS2000 Voice Mail Setup
Installation
●Refer to your DS2000 Hardware Manual for instructions on setting
up analog ports for Voice Mail. Each Voice Mail port requires a cor-
responding analog port in your telephone system. Depending on
your installation requirements, your DS2000 system can use ASTU
PCBs or 2-OPX Modules for analog ports.
●Refer to your Voice Mail manuals for the details on connecting
Voice Mail to the DS2000 analog ports.
Telephone System Programming
1801 - Extension Circuit Type
●If you are using a 2-OPX Module (P/N 92177A only), assign circuit
type 21.
●If you are using Analog Station (ASTU) PCB ports, assign circuit
type 15.
0510 - Hunt Group Number
●Select an available UCD Hunting group (1-8) for Voice Mail.
0510 - Hunt Group Master Number
●Assign an unused extension number as the Voice Mail Hunt Group
master number. Valid numbers are 100-899, excluding the extension
and trunk number range. For example, your master number cannot
be 308 or 401.
0201 - Voice Mail Installed
●Enter Y.
0201 - Voice Mail Master Extension Number
●Enter the master number you assigned in 0510 - Hunt Group
Master Number above.
1802 - Voice Mail Port
For each analog port connected to Voice Mail, enter Y. (These are the
ports you programmed in 1801 - Extension Circuit Type above.)
1807 - Hunt Type
For each analog port connected to Voice Mail, enter 5 (for UCD).
Press VOL ▲and VOL ▼to verify your entry.
1807 - Hunt Master Number
For each analog port connected to Voice Mail, enter the master exten-
sion number you assigned in 0201 - Voice Mail Master Extension
Number above. Press VOL ▲and VOL ▼to verify your entry.
DS2000 Voice Mail Setup
Installation
●Refer to your DS2000 Hardware Manual for instructions on setting
up analog ports for Voice Mail. Each Voice Mail port requires a cor-
responding analog port in your telephone system. Depending on
your installation requirements, your DS2000 system can use ASTU
PCBs or 2-OPX Modules for analog ports.
●Refer to your Voice Mail manuals for the details on connecting
Voice Mail to the DS2000 analog ports.
Telephone System Programming
1801 - Extension Circuit Type
●If you are using a 2-OPX Module (P/N 92177A only), assign circuit
type 21.
●If you are using Analog Station (ASTU) PCB ports, assign circuit
type 15.
0510 - Hunt Group Number
●Select an available UCD Hunting group (1-8) for Voice Mail.
0510 - Hunt Group Master Number
●Assign an unused extension number as the Voice Mail Hunt Group
master number. Valid numbers are 100-899, excluding the extension
and trunk number range. For example, your master number cannot
be 308 or 401.
0201 - Voice Mail Installed
●Enter Y.
0201 - Voice Mail Master Extension Number
●Enter the master number you assigned in 0510 - Hunt Group
Master Number above.
1802 - Voice Mail Port
For each analog port connected to Voice Mail, enter Y. (These are the
ports you programmed in 1801 - Extension Circuit Type above.)
1807 - Hunt Type
For each analog port connected to Voice Mail, enter 5 (for UCD).
Press VOL ▲and VOL ▼to verify your entry.
1807 - Hunt Master Number
For each analog port connected to Voice Mail, enter the master exten-
sion number you assigned in 0201 - Voice Mail Master Extension
Number above. Press VOL ▲and VOL ▼to verify your entry.
NVM-Series instructions are on the other side. NVM-Series instructions are on the other side.

NVM-Series Voice Mail Setup
!! IMPORTANT !!
Use the following steps only if your NVM-Series Voice Mail does not include
DS2000 on the IN - Install System menu.
Set up the Voice Mail Database
●Select IN - Install System.
●Reinstall the Voice Mail for DS01/VS (24 x 72) and customize the
trunk numbers to begin with 401.
Change the Voice Mail Call Pickup String
●Select CU - Customize Database.
●Select SO - System Options.
●Change the Call Pickup String option to W**.
Change the Voice Mail Park and Page String
●Select CU - Customize Database.
●Select MO - Mailbox Options.
●Enter the extension’s mailbox number (e.g., 300 for extension 300).
●For the mailbox selected (e.g., 300), change the Park/Paging string
option to FW**nnn/*10 (where nnn is the extension’s number).
For extension 300, for example, the string would be
FW**300/*10.
NVM-Series Voice Mail Setup
!! IMPORTANT !!
Use the following steps only if your NVM-Series Voice Mail does not include
DS2000 on the IN - Install System menu.
Set up the Voice Mail Database
●Select IN - Install System.
●Reinstall the Voice Mail for DS01/VS (24 x 72) and customize the
trunk numbers to begin with 401.
Change the Voice Mail Call Pickup String
●Select CU - Customize Database.
●Select SO - System Options.
●Change the Call Pickup String option to W**.
Change the Voice Mail Park and Page String
●Select CU - Customize Database.
●Select MO - Mailbox Options.
●Enter the extension’s mailbox number (e.g., 300 for extension 300).
●For the mailbox selected (e.g., 300), change the Park/Paging string
option to FW**nnn/*10 (where nnn is the extension’s number).
For extension 300, for example, the string would be
FW**300/*10.
Part No. 80000VMSET02
Issue 1-0 April 2001 Printed in U.S.A.
NEC America, Inc., Corporate Networks Group
4 Forest Parkway, Shelton, CT 06484
TEL: [phone] FAX: [phone]
cng.nec.com Part No. 80000VMSET02
Issue 1-0 April 2001 Printed in U.S.A.
NEC America, Inc., Corporate Networks Group
4 Forest Parkway, Shelton, CT 06484
TEL: [phone] FAX: [phone]
cng.nec.com