Ness Navigator Quick start guide

Touch Screen Keypad
InstallatIon notes
Alarm Control Panels
Compatible with

2
J1
RECEIVERLISTEN SERIAL READER
PROG
TAMP
BATTERY
RED +
TELEPHONE
HEATSINK
AUX1
AUX2
AUX3
AUX4
+12V
0V
TAMP
+12V
+12V
+12V
0V
Z8
C
Z7
Z6
C
Z5
Z4
C
Z2
Z3
C
Z1
0V
CLK
DAT
COM
KEYPAD
RESET
STR
SIREN
17V
AC
AC
EARTH
BLACK
BOX TAMPER
SWITCH
N.C. Contacts
(WHITE)
J1 LINK
&BOX TAMPER PROGRAM LINK
= Sealed, normal state
=Tamper alarm state
Power up with link off to enter
installer program mode
BATTERY LEADS
(supplied)
“HEARTBEAT” LED
Constantly flashes
D8X MAIN BOARD
LISTEN PINS
Diagnostics. Connect an
8 Ohm horn speaker to
listen to dialler tones.
BATTERY CONNECTION
For 12V 7Ah backup
battery (BAT210)
RECEIVER
Header for
connecting
optional Radio
Interface.
AUX
Aux outputs
1-4.
SERIAL
Connection for
direct up/download
using NessComms
software
READER
Connection for
up to3Ness
Weigand readers
D8x / D16x V7
Main Board
Blue
White
Black
Red
DAT
CLK
COM
+12V
Wiring
Navigator Keypad REAR
3 pin header.
FACTORY USE ONLY
4 pin header.
NAVIGATOR WIRE
LOOM
Crimp connectors
(Supplied)
Installation
To open the Navigator Touch
Screen keypad, release the
four locking slots with a small
screwdriver.
Install the back housing on a
flat surface using the two slotted
mounting holes provided.
The alignment arrow indicates
the correct way up.
Navigator Touch Screen Keypad should be wired to the control panel using
minimum 7/020 security cable.
Up to four Navigator keypads
can be connected per control
panel as long as the maximum
current draw for all detectors
and keypads is below 500mA.
Maximum allowable cable
distance is 100m including
cable to all keypads.
Wire additional keypads in
“star” configuration to the
control panel.
This way
Navigator Keypad back housing.
Cable entry
Mounting holes x 2
Locking slots x 4

3
Applying the Protective Film
Navigator Touch Screen Keypad is supplied with a self-adhesive screen
protector to help protect the sensitive touch surface from marks and
scratches which may appear under normal use. We highly recommend
you apply the film to keep your touch screen looking brand new for years
to come.
Please peel off this
mask BEFORE application
STEP 1.
Use the Number tab to peel off the
self-adhesive backing.
STEP 2.
Flip the film over to position the No. 2
tab at the top left.
STEP 3.
Holding the protective film by
the No. 2 tab, carefully apply
the film to the Navigator’s
screen. Start applying at one
end and smooth the film as
you go to remove any air
bubbles
STEP 4.
Use the No. 2 tab to peel off
and discard the topmost layer
of the film.
Your Navigator is now ready
for use.
Please peel off this mask
AFTER application completed
Please peel off this mask
AFTER application completed

4
DIMENSIONS 108w x 86h x 15d mm.
DISPLAY TYPE 3.5" Colour LCD
DISPLAY RESOLUTION 320 x 240
TOUCH SCREEN Touch sensitive surface
COMPATIBILITY D8x & D16x control panels version 7 and later
MAX. KEYPADS 4 x Navigator Touch Keypads per panel
Maximum current draw for all detectors and keypads should
not exceed 500mA.
OPERATING VOLTAGE 12VDC supplied by the control panel
CURRENT DRAW 25mA with 50% backlighting
50mA with 100% backlighting
DATA 2 wire proprietary Ness data bus
Specifications
NAVIGATOR TOUCH SCREEN KEYPAD
INSTALLATION NOTES
Rev 2, Apr13
Document Part Number: 890-411
Compatibility
Navigator Touch Screen keypad
is compatible with Ness D8x and
D16x Version 7 and later control
panels.
The keypad will display a
warning if connected to
earlier panel versions.
www.nesscorporation.com
National Customer Service Centre
Ph: 1300 551 991
[email protected]