Newstripe EcoLiner SP User manual

1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
EcoLiner™ SP
Product Manual

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 1of 1
Precautionary Warning............Page 1
Assembly.................................Page 2
Operation................................Page 3
Cleaning Procedure .................Page 4
Cleaning Procedure .................Page 4
(Winter Storage)
Parts List..................................Page 5
Spray Gun Assembly................Page 6
Images..................................Page 7-9
Maintenance ...........................Page 9
Troubleshooting Guide..........Page 10
Warranty...............................Page 11
Thank you!For your purchase of the
Newstripe ECOLINER™ SP sprayer.
Please read over the instructions and
make sure you understand operating
procedures before using the unit.
Please check the serial number on your
unit. This Manual is for units with a
Honda Engine, and serial number
1025474 and above only. For units with
serial numbers below 1025474, please
contact Newstripe for the correct
manual.
WARNING!
DO NOT use latex paints from hardware stores or home improvement
centers in your machine. These types of paints have binders in them that
will adhere to the internal parts of the pump, causing damage. You will
not be able to clean these substances from the pump. You must use a
good quality true water base athletic field striping paint in your machine.
This type of damage is NOT COVERED UNDER WARRANTY!

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™SP Manual / 5122.0223
Page 1of 11
PRECAUTIONARY WARNING!
Please read and understand all operation instructions as
detailed in this manual. Failure to follow specified
instructions may result in equipment damage or serious
injury to personnel up to and including death!
DO NOT use oil, solvent base, primer, or base coat paints
in the EcoLiner™ SP.
Before using paint, fill the paint pail with water and practice
spraying, to familiarize yourself with the machine.
ALWAYS STRAIN THE PAINT. Field marking paint often has
oversized material, lumps, skin, etc., in it. If not strained,
these contaminates will be drawn into the pump, shut-off
valve, lines, etc., and will cause problems.
THIN THE PAINT BEFORE adding it to the pail of the
ECOLINER. Almost all field marking paints MUST BE
THINNED before using them with the ECOLINER. These
paints are typically thinned at ratios of 1:1 (One-gallon of
water to one-gallon of paint) up to 3:1.
NEVER perform maintenance on the machine while the
system is running.
If equipped with fuel shut off, the gas On/Off lever should
always be OFF when the machine is not being used
DO NOT run the pump dry after cleaning.
Please note that modifying, changing or servicing any
portion of the machine, system or components outside of
the procedures and parts outlined in the owner’s manual
will VOID the warranty.
Use only in well-ventilated area.
Always consult your Facility Safety and/or Personnel
Department for specified safety protocols prior to
operating this equipment.

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 2of 11
ASSEMBLY
1. The EcoLiner™SP is shipped mostly assembled. You are only required to attach the spray gun assembly and
paint hose.
2. Slide the Support Arm with side plates through the mounting tube on the front of the chassis.
3. Tighten down the Star Knobs.
4. Mount the Spray Gun Mounting Arm on the Support Arm with the spray hose connection facing rearward.
5. Tighten the Star Knob on the gun mount.
6. The line width is adjusted by raising or lowering the Spray Gun and selecting the appropriate Spray Nozzle.
7. Connect the Paint Hose from the Shut-Off Valve to the Spray Gun. Tighten lightly with a wrench.
8. CHECK THE ENGINE OIL. FILL THE ENGINE TO THE PROPER FULL LEVEL WITH HIGH QUALITY 10W30
DETERGENT MOTOR OIL.The full level is between the cross hatched markings on the dipstick with the
dipstick pushed against the fill port. (Not screwed in.)
Your EcoLiner SP box should include:
Support arm for spray gun with left & right
side spray shields
Gun mounting Bar
Spray gun assembly
Nozzles, 5002 (2”-3” lines) and 9005 (5”-6”
lines)
Pail paint strainer
Owner’s Manual
Pic 1

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 3of 11
OPERATION
1. Adjust the spray shields to a 4” width. You may have to raise or lower the spray gun so that the machine will
produce a 4” line. To stripe narrower or wider lines, select the proper spray nozzle from the selection guide and
adjust the spray shields. Adjust the spray gun as needed to produce the required line width.
2. Move pump engagement lever to the “OFF” position, towards the rear of the machine.
3. Disengage the self-propelled drive mechanism by pulling the lever back towards the rear of the machine.
4. Add water (for testing, practicing, or cleaning) or premixed paint to the pail.
5. Move the On/Off gas lever to the “On”position. Move the choke lever to the “Choke” position. Move the
throttle lever to about the ¾ position. Turn the On/Off switch to “On” position. Pull starter chord. Once the
engine begins to run, move the choke lever to the “Run”position. Adjust the throttle to just over the ½ position
where the engine is running smoothly.
6. Move the pump engage lever to the “ON” position, all the way forward. The engage lever should now be in a
horizontal position.
7. Turn the lever on the Pump Prime Valve next to the Pressure Valve and Cable, to the open position. Lift the lid
slightly on the pail and watch the paint flow from the hose. Once there is a continuous flow from the hose,
close the Pump Prime Valve. The unit should now spray when the handle mounted trigger is squeezed.
8. To engage the self-propelled mechanism, simply push the drive lever to the forward most position. Pull
back to stop. The speed is controlled by adjusting the engine speed.
OPERATIONAL NOTES!
a) Adjust the side spray shields for the line width and adjust spray gun height up or
down as needed to achieve the line width. (Note: water will produce a wider
line than paint.)
b) Fill the pail to about 2” from the top with PREMIXED paint. DO NOT fill the unit
with non-thinned paint, as this will clog the pump. Most athletic field marking
paint is mixed at a ratio of 1:1, one gallon of water to one gallon of paint. Some
paints may be thinned more. See the paint manufacturer’s directions.
c) You will need to use the Pump Prime valve each time you run the pail dry and
when you switch to water for cleaning to remove air in the system. The spray
pressure valve is initially set at the factory for maximum spray pressure. If you
feel you are getting too much paint flow from the nozzles, unscrew the Pressure
Valve Cap until the flow is where you would like it to be and then run the
Locking Ring up against the cap to maintain the setting.
ALWAYS Disengage the pump lever when the paint pail becomes empty. Continuing to
run the pump when paint has run out will dry paint inside the pump

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 4of 11
CLEAN UP PROCEDURE AFTER EACH USE
1. When your Striping job is complete, pull the Paint Return Hose & Prime Valve Hose out of the lid and point them
towards the ground behind the machine or in a separate pail.
2. Remove the pail lid and set it aside. Pull the suction hose out of the pail and place it to side of the machine or in
a separate pail.
3. Empty the pail on the machine of unused paint, or remove the pail completely and cover it for the next time
that you stripe.
4. Place an empty pail on the machine.
5. Wipe off or rinse off the suction hose, screen, return hose, pump prime hose, and pail lid.
6. Remove the nozzle cap, nozzle, and valve seat, and put them in a container of water to soak.
7. Add 2-3 gallons of clean water to the pail. Place the suction hose in the pail on the machine, but leave the
return hose out. This allows you to flush all of the hoses of paint. Start the engine. Use the Pump Prime valve to
prime the pump and activate the control lever. CAREFUL: The Return Hose may ‘jump’ from the paint pressure.
Run until the spray runs clear.
8. Clean the nozzle parts that have been soaking and reassemble them onto the spray gun.
9. Clean and rinse the exterior of the machine. Use soapy water (dish washing detergent or Simple Green) once
each week to thoroughly clean the pump. Add soap to 2-3 gallons of water, run the machine and let it circulate
back to pail for 10-15 minutes, and then empty the pail.
CLEANING PROCEDURE FOR WINTER (FREEZING) STORAGE
1. Clean as instructed in the cleaning procedure.
2. Remove as much fuel from the engine gas tank as you can. Run the engine until it runs out of gas.
3. Disconnect the suction and pressure hoses at pump and drain.
4. Disconnect the paint hose from pressure valve and drain the hose.
5. Open the pump prime valve and place the pump prime valve hose on the ground to drain the valve.
6. The machine may now be stored in freezing temperatures.
7. Drain and change the engine oil in the spring.

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 5of 11
SPRAY GUN ASSEMBLY
(Item 10001949)
Item Description Part Number
57 Valve Seat 10000136
58 Nozzle Select nozzle
59 Nozzle Cap 10001890
*8004 Tip preinstalled by the factory
SELECT NOZZLE FOR APPLICATION
Item Description Part Number
5002 2” Line (package of 4) 10001891
8005 4” -5” Line (Heavy Turf) 10003493
8004 4”-5” Line (package of 4 10001893
**Comes standard on the machine
9505 5”-6” Line (package of 4) 10001894
Nozzle Cap #59
Nozzle #58
Valve Seat #57
Spray
Gun #16

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 6of 11
PARTS LIST
Item
Description
Part
Number
Item
Description
Part
Number
1
Chassis
10004610
29
Hose Assembly, Pump Pressure
10004469
2
Engine, Honda GX120
10000371
30
Hose Assembly, Pump Prime
10003692
3
Air Filter Element for Engine (Not Shown)
10000401
31
Brass Tee Fitting, ½”
10004111
4
Wheel Assembly
10000012
32
Brass Reducer Fitting , ½” – ¼”
10002481
5
Handles
10002023
33
Pump Prime Valve
10000233
6
Handle Support Brace
10004612
34
Brass Male Elbow Fitting, ¼”
10000159
7
Control Cable
10002518
35
Brass Cross Fitting, ¼”
10000235
8
Control Lever
10002951
36
Brass Street Elbow Fitting, ¼”
10004131
9
Throttle Cable
10000696
37
Brass Plug Fitting, ¼”
10000113
10
Drive Lever
10002072
38
Brass Ball Seat Fitting, ¼”
10000731
11
Drive Rod
10002087
39
Pump Engage Lever
10001817
12
Hose Assembly, Paint
10000695
40
Belt Guard
10002030
13
Hose Assembly, Suction
10004470
41
Pump Inlet/Outlet Elbow Fittings
10004459
14
Suction Filter (Not shown)
10002842
42
Pump, 1.8 GPM Diaphragm
10003367
15
Spray Gun Mount
10004651
43
Drive Assembly
10002088
16
Spray Gun Assembly
10001949
44
Drive Roller
10003387
17
Spray Gun Support Arm
10003550
45
Gun Mount Star Knob
10004480
18
Pivot Assembly with Spray Shield, Right
10004825
46
Belt, Drive (A26)
10001757
19
Pivot Assembly with Spray Shield, Left
10004824
47
Belt, Pump (3L260)
10001755
20
Spray Shield (Included w/ Pivot Assembly)
10003562
48
Pulley, Pump Belt Idler
10001111
21
Star Knob
10000007
49
Pulley, Drive Idler
10001111
22
Cable Adjuster with Nut
10000018
50
Pulley, Drive
10001115
23
Cable Stop
10001577
51
Pulley, Engine
10001739
24
Pressure Valve Adjusting Cap
N/A
52
Pulley, Pump (not shown)
10003368
25
Locking Ring
N/A
53
Spring, Pump Belt Tensioner
10000649
26
Pressure Limiter Collar
N/A
54
Spring, Drive Belt Idler Arm
10000692
27
Pressure Valve
10003478
55
Bearing, Pump Shaft
10003131
28
Hose Assembly, Return
10003692
56
Pump Shaft
10003365
ENGINE LUBRICANT AND PARTS
ITEM
SPECIFICATIONS
Engine
Part Number 10000371, Honda GX120 With Oil Alert
Oil Capacity
18 Ounces (0.56 Liters) Full Synthetic 5W-30
Spark Plug
NGK Part Number BPR6ES or Denso Part Number W20EPR-U
Air Filter
Part Number 10000401

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 7of 11
#13 Suction
Hose
#7 Control
Cable
#5 Handles
#8 Control
Lever
#28 Return
Hose
Pic 2
#30 Pump Prime
Return Hose
#12 Paint
Hose
#6 Handle
Support Brace
Pic 3
#24 Pressure Valve
Adjusting Cap
#25 Locking
Ring
#26 Pressure
Limiter Collar
#27 Pressure Valve
#28 Return
Hose
#12 Paint Hose
#31 Brass Tee
Fitting, ½”
#29 Pump
Pressure Hose
#30 Pump
Prime Hose
#32 Reducer
1/2”-1/4”
Brass T
fitting, ½”
#35 Cross
Fitting ¼”
#36 Brass
Elbow ¼”
#34 Brass
Elbow ¼”
#33 Pump
Prime Valve
#38 Ball
Seat Fitting
#37 Plug
#1 Chassis
#4 Wheel Assembly
#2 Honda
GX120 Engine
#10 Drive
Lever

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 8of 11
#18 Right
Pivot Assy.
#15 Spray Gun
Mount
#45 Gun Mount
Star Knob
#20 Spray
Shield
#19 Left
Pivot Assy.
#16 Spray Gun
#41 Pump
Elbow Fittings
#43 Drive
Assembly
#29 Pump
Pressure Hose
Pic 4
#44 Drive Roller
Pic 5
#42 Pump
#40 Belt Guard
#13 Suction Hose
#39 Pump
Engage Lever
#11 Drive Rod
#9 Throttle Cable
#44 Drive rollers
#21 Star Knobs
#20 Spray
Shield
#17 Spray Gun
Support Arm
Trigger Lifting Bar
#12 Paint Hose
#22 Cable Adjuster
with Nut & #23
Cable Stop

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 9of 11
MAINTENANCE
ITEM
CHECK
MAINTENANCE ACTION
Engine Oil Level
Prior to every use
Change the engine oil after the first 20 hours of operation
and then every 100 hours thereafter.
Paint Pail/Tank
After every use
Clean the paint pail/tank, hoses and nozzle.
Hoses and Pump
After every use
Run soapy water through the pump and hoses for additional
cleaning.
Wheels
Check the air level before
each use
Fill the tires with air as needed. Grease the wheel bearings
weekly.
Handles
Monthly
Check the handles for tightness to the chassis.
Engine Air Filter
Monthly
Clean the filter monthly. Replace the filter every 4 months.
**For additional instructions please contact Newstripe, Inc. at 800-624-6706
#55 Pump
Shaft Bearing
#56 Pump Shaft
# 47 Pump Belt
(3L260)
#51 Engine
Pulley
#44 Drive Roller
#48 Pump Belt
Idler Pulley
#39 Pump
Engage Lever
Pic 6
#54 Drive Idler
Arm Spring
#53 Pump Belt
Tensioner Spring
#49 Drive
Idler Pulley
#46 Drive Belt
(4L280)
#50 Drive
Pulley

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 10 of 11
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
REMEDY
Pump will not prime
Air in the pump
system
Open the pump prime valve and check for flow from the hose into the
pail. When the flow is continuous, close the valve.
Pump will not prime
after relieving the
air in the system
The pump may be
clogged with paint
Disconnect the supply and discharge hoses. Clean out the hoses. Pour
hot water into the opening of the pump and let it soak. Reconnect the
hoses and start the pump again.
Pump still won’t
prime due to the
clog in the system
The spray system was
not properly cleaned
after the previous use.
If hot water alone does not remove the clog, pour liquid dish soap or
“Simple Green” product into the pump inlet. Jog the pump by
pulling the starter cord several times with engine off to get the soap
in to the pump and let it soak 15-30 minutes, then try pumping
water. The pump does not need to be rinsed of all the soap as the
soap will mix easily with the paint. If it still will not work, call the
factory.
Disassembly of the pump will VOID the warranty.
Pump will not run
Loose or broken pump
belt
Inspect, adjust, or replace the belt. The belt should deflect
approximately ½” between the pulleys.
Paint is leaving the
nozzle in a stream,
and not spraying.
The paint is too thick
Thin the paint.
Pressure is too low
See step C in the operational notes (Page 3)
Spray is inconsistent
Obstruction in the gun
nozzle
Remove the gun nozzle, and clean or replace it.
Clogged or obstructed
suction hose filter
Always strain the paint before adding it to the pail. Remove the
suction hose and filter, and clean them before replacing.
Spray pattern is too
narrow or uneven
Wrong nozzle or the
spray head height is
incorrect
Adjust the spray head up or down and or install the proper nozzle.
The nozzle slot must be crosswise to the gun body.
The paint is too thick
Thin the paint.
Paint drips after
being shut off
The control cable out
of adjustment
Check the cable at the spray gun mount. Adjust or replace the cable
as needed.
Clogged or worn spray
control valve
Dissemble and clean, or replace the valve.
The gun is not in the
gun mount correctly
Adjust gun position in the mount so that the lifting bar allows the
spray trigger to release properly.
Faulty control lever
Replace the faulty control lever.
Drive unit will not
move machine
The drive rollers are
turning, but there is
no movement
The drive rod is out of adjustment. Adjust it by removing the hair
pin clip and turning the adjustment nut clockwise, and then re-
installing. MAKE sure both tires are inflated equally.
Drive rollers are not
turning
Worn belt or broken idler spring. Replace the belt or spring as
needed.

ECOLINER™ SP
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ SP Manual / 5122.0223
Page 11 of 11
THE NEWSTRIPE WARRANTY – 18 MONTH
NEWSTRIPE, INC., WARRANTS TO THE ORIGINAL PURCHASER, FOR 18 (EIGHTEEN) MONTHS AFTER DATE OF
PURCHASE, THAT THE EQUIPMENT* HEREBY SOLD SHALL BE FREE OF DEFECTS IN MATERIALS AND
WORKMANSHIP. THIS WARRANTY DOES NOT EXTEND TO ANY DAMAGE OR MALFUNCTION RESULTING
FROM MISUSE, NEGLECT, ACCIDENT, IMPROPER OPERATION, OR NORMAL WEAR AND TEAR.
Damage incurred in shipment from Newstripe, Inc. to the customer is the total responsibility of the carrier.
The CUSTOMER MUST NOTE DAMAGES on the Bill of Lading of Trucking Company or Railroad; and
Newstripe, Inc. will furnish to the customer the cost or parts and labor. The customer can then bill the
common carrier for the damages by placing his signature on the documents.
The Newstripe, Inc. obligation under this warranty and any implied warranties is limited to replacement or
repair of defective parts of its manufacture without charge for 18 (Eighteen) months from date of purchase.
For service under this warranty, buyer shall ship the defective part or parts of the equipment,
transportation prepaid, to Newstripe, Inc. together with a written description of any claimed defect and
proof of purchase date of the materials being returned. Prior to retuning any part or machine, the
CUSTOMER must obtain a Return Materials Authorization number. Call 1-800-624-6706.
*Gasoline engines, compressors, pumps (including airless) and Transaxles are furnished with their
respective manufacturer's warranties only. Such components are not covered by any warranty of
Newstripe, Inc. Where Newstripe elects to extend manufacturers’ warranties, the warranty shall be pro-
rated as to cover 100% of the cost to replace or repair materials and parts for the first 12 months of
ownership and 60% for the remaining 6 month period.
The responsibilities described above are the only responsibilities of Newstripe, Inc. under this written
warranty or any implied warranty, and may be exercised only within 18 (Eighteen) months from the date of
purchase. In no event shall Newstripe, Inc. be liable for incidental or consequential damages and no person
had any authority to bind it to any representation or warranty, not be responsible for work done, materials
furnished or repairs made by others without its' specific written authorization.
THIS WARRANTY SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND THERE
IS NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND WITH RESPECT TO THE GOODS SOLD HEREBY
EXCEPT AS SET FORTH HEREIN. IT IS EXPRESSLY AGREED THAT THIS WARRANTY SHALL BE LIMITED TO THE
ADJUSTMENT, REPAIR OR REPLACEMENT OF PARTS AND THE LABOR AND SERVICES REQUIRED THEREBY. IN
NO EVENT, INCLUDING ANY CLAIM FOR NEGLIGENCE, SHALL NEWSTRIPE, INC. BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
Sincerely,
Newstripe, Inc.