Newstripe EcoLiner User manual

Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
EcoLiner ™
Product Manual

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
TABLE OF CONTENTS
Precautionary Warning…........ Page 1
Assembly……………………………...Page 2 -3
Operation …………………………….Page 4
Recharging the Battery………….Page 5
Cleaning Procedures…………..…Page 6
Maintenance……………………….. Page 6
Parts List with images…………...Page 7-8
Troubleshooting………………….. Page 9
Warranty…………………………….. Page 10
Thank you!And Congratulations on
your purchase of the EcoLiner™paint
marking machine.
With proper care, service and clean
up, the Newstripe EcoLiner™is
designed to give you years of trouble
free, accurate line marking. It is
important to familiarize yourself with
the machine before start-up. Please
take the time to THOROUGHLY READ
THIS MANUAL. This will guarantee a
good start using your EcoLiner™and a
longer, trouble free machine life.
Please check the serial number on
your unit. This Manual is for units with
serial number 1017478 and above
only. For units with serial numbers
below 1017478, please contact
Newstripe for the correct manual.

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
PRECAUTIONARY WARNING!
Please read and understand all operation instructions as
detailed in this manual. Failure to follow specified instructions
may result in equipment damage or serious injury to personnel
up to and including death!
ALWAYS STRAIN THE PAINT. Field marking paint often has
oversized material, lumps, and debris. If not strained, these
contaminates will be drawn into the pump, shut-off valve, hoses,
etc., and may restrict paint flow.
THIN THE PAINT, as per manufacturer’s recommendations prior
to placing the suction hose into the paint bucket. Almost all
field-marking paints MUST BE THINNED before use with the
EcoLiner™. These paints are typically thinned at a minimum ratio
of 1:1. Follow suggested paint thinning guidelines per the paint
manufacturer’s instructions.
NEVER perform maintenance on the machine while the system is
running
Please note that modifying, changing or servicing any portion of
the machine, system or components outside of the procedures
and parts outlined in the owner’s manual will VOID the
warranty.
Always consult your Facility Safety and/or Personnel
Department for specified safety protocols prior to operating
this equipment.

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
ASSEMBLY
1. Remove packing from around parts box, pail
lid, chassis and set aside. Leave foam wraps
on handle braces at this time.
2. Rotate the handles to their raised position, while
lifting up on the rear of the machine.
3. Remove the foam wraps from the handle braces.
4. Position the spray hose so that it is in front of the
handle.
5. Insert one carriage bolt through the left hand
brace and handle from the outside. Use one
female star knob to secure the brace.
6. Insert the second carriage bolt through the right-
hand brace and handle from the outside. (Pic 2)
7. Place the retaining clip for the spray hose over
the bolt and secure with a female star knob.
8. Insert support arm into receiver tube on right-
hand side of the chassis until it stops and secure
with one large star knob.
Required Items and Tools
18AH SLA, 12 volt motorcycle battery with dimensions of 6 7/8”l x 3 7/16”w x 6 1/8”h (Not Included)
1/2” Wrenches or adjustable crescent Wrenches (2 required)
Your EcoLiner™ box should include:
Chassis/Handle assembly with paint spray hose attached
Paint pail lid
Cloth/mesh strainer
Parts bag containing:
(2) female star knobs
(2) large star knobs
(2) carriage bolts
Spray head support arm
Spray nozzle assembly
Paint suction hose
Owner’s manual
Pic 1
Pic 2
#15 Large Star
Knobs
#6 Spray Head
support Arm
#18 Spray
Nozzle
Assembly
Cloth/Mesh
Strainer
#9 Dip Tube
Hose
#16 Female
Star Knobs
#10 Suction
Filter

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
9. Slide spray nozzle onto upright with mounting
tube facing forward and nozzle facing downward.
Secure with one large star knob. Raise or lower
to adjust line width.
10. Attach spray hose to brass elbow and lightly
tighten with a wrench. (Pic 3)
11. Attach suction hose to pump inlet and hand
tighten only. (Pic 3)
12. Install one 18AH SLA 12 volt battery (Not
included) into battery tray and attach the two
black wires to the negative (-) terminal and the
red and white wires to the positive terminal (+).
(Pic 4, 5)
Pic 3
Pic 4
Pic 5

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
OPERATION
1. Always pre-lubricate the sprayer with water
prior to operation. Fill the pail ½ full with water
and secure the lid, making sure the suction hose
with filter screen is at the bottom of the pail. It
is advisable to familiarize yourself with the
equipment operation by using water the first
time.
2. Turn on the pump with spray rocker switch on
the handle. Allow 15-30 seconds for the pump
to prime.
3. The unit is shipped with the nozzle for a 4” wide
line installed. Note: The height of the spray
nozzle will increase or decrease the line width.
Raise or lower as needed
4. Unsnap the pail lid and pour properly thinned
paint into the pail.
NOTE: These paints are typically thinned at a
minimum ratio of 1:1. Follow suggested paint
thinning guidelines per the paint manufacturer’s
instructions.
5. Press the forward part of the spray rocker
switch to the on position. Allow 15-30 seconds
for the pump to prime. Check for leaks and
tighten any fittings as required.
NOTE: Back position is momentary on, center is
off, forward position is continuous operation.
6. Position the spray nozzle and shields where the
painted line is to begin, and engage the spray
rocker switch to desired position. An even flow
of paint should spray from the nozzle.
7. Put spray rocker switch into center position,
when you would like to machine to stop
spraying.
OPERATIONAL NOTE!
NOTE: If the pump does not run, check the fuse in the blue fuse
holder. Check first to make sure the fuse is pushed in all the way. If
this is not the problem, replace the fuse. If the unit will still not run,
and both power supply cables are attached correctly to a fully
charged battery, contact Customer Service at 1-800-624-6706.

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
RECHARGING THE BATTERY
Before using the battery charger, Please Read All Instructions.
1. Plug charger in any standard 110 volt AC outlet.
PRECAUTIONARY WARNING!
Before using the battery charger, Please Read All Instructions.
NOTE: The power supply cord does not have to be detached to
recharge the battery. However, the spray pump toggle switch must
be in “OFF” position.
NOTE: If all connections are correct, have the battery inspected for
function at a reputable dealer.
Pic 6

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
CLEANING PROCEDURES
CLEAN AFTER EVERY USE
1. When your striping job is complete, remove the pail
lid and set aside. Pull out the suction hose and
place it in a clean water container. Empty pail of
unused paint, or remove pail completely and cover
for use the next time you stripe. Place another
empty pail on machine.
2. Wipe off or rinse off pick up tube, screen on pick up
tube, and pail lid.
3. Remove nozzle cap, nozzle, and nozzle screen and
put in container of water to soak.
4. Place 2 gallons of clean water in the pail. Place the
suction hose back in pail. Turn on the spray rocker
switch and spray through nozzle.
5. Turn on the spray rocker switch to “spray” position
and flush clean water through nozzle.
6. Operate spray nozzle until the gun is cleared of all
paint.
7. Clean nozzle parts that have been soaking and
reassemble on spray valve.
8. Clean and rinse exterior of machine. Pressure
washing is not recommended. Use soapy water
(dishwashing detergent or Simple Green) once each
week.
NOTE: Always leave some of the cleaning solution
or Newstripe’s pump protector in the pump when
not in use. This keeps the internal pump
components lubricated. DO NOT run the pump
without liquid. If you need to store the unit for
extended periods or in freezing areas, run water
and dishwashing detergent through the pump to
clean out all paint and replace with Newstripe’s
pump protector. For further protection, order
Newstripe pump protector to use during storage.
MAINTENANCE
ITEM
CHECK
MAINTENANCE ACTION
Paint Pail/Tank
After every use
Clean paint pail/tank, hoses and
nozzle
Hoses and Pump
After every use
Run soapy water through pump for
additional cleaning
Handles
Monthly
Check handles for tightness to frame
**For additional instructions please contact Newstripe, Inc at 800-624-6706

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
PARTS LIST
Item Part
Number Description Number
#1 Chassis 10004487
#2 Handle 10004488
#3 Handle Support Braces (2) 10004489
#4 Spray Head 10004492
#5 Spray Control, Rocker Switch 10004474
#6 Support arm (for spray head) 10004491
#7 Lid, 5-gallon pail 10004516
#8 Pump, 12 volt, diaphragm 10004551
#9 Hose, Dip Tube 10004498
Item Part
Number Description Number
#10 Suction filter, dip tube
(Not Shown) 10002842
#11 Power Supply Harness
(To Battery) 10004499
#12 Fuse ATO/ATC 20 Amp 10002836
#13 Hose, Paint (Standard) 10004497
#14 Spray shields (2) (optional kit) 10004507
#15 Star Knob (2) 10000007
#16 Female Star Knob 10004480
#17 Wheel & Tire Assembly 10004705
NOZZLE ASSEMBLY
Item Description Part Number
#18 Nozzle Assembly 10001519
(Includes items 19-23)
#19 Nozzle Select Nozzle
#20 Nozzle Cap (pkg of 4) 10001890
#21 Nozzle Screen (pkg of 4) 10003496
#22 Nozzle Body 10000028
SELECT NOZZLE FOR APPLICATION
Item Description Part Number
5002 2” Line 10001891
8005 4” -5” Line (Heavy Turf) 10003493
8004 4”-5” Line (Turf/Asphalt) 10001893
8002 4”-5” Line (Concrete) 10001892
9505 5”-6” Line 10001894
#20 Nozzle
Cap
#22 Nozzle
Body
#21 Nozzle
Screen
#19 Nozzle

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
+
#7 Lid
#9 Dip Tube
hose
#17 Wheel / Tire
Assembly
#13 Paint
Hose
#2
Handle
#5 Rocker
Switch
#15 Star
Knob
#4 Spray Head
Battery Tray
Pic 7
Pic 8
Pic 9
Pic 10
#18 Nozzle
Assembly
#8 Diaphragm
Pump
#11 Power
Supply Harness

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
REMEDY
Pump will not run
Battery not charged
Fuse blown
Fuse disconnected
Charge Battery
Change Fuse
Check fuse holder connection and wires
Pump will not prime
Pump or hoses may be restricted
Disconnect supply and discharge hoses. Clean
out hoses. Pour hot water into inlet opening of
pump and let soak. Reconnect hoses and start
pump again.
Pump still won’t prime
If hot water alone does not remove clog, pour
liquid dish soap or the “Simple Green” product
into the pump inlet. Jog the pump
(operate toggle switch briefly) to get the soap
into the pump and let it soak (15-30 minutes).
Attach hoses and try pumping water. If pump
start pumping, let it circulate on the water for
5-10 minutes before adding paint. The pump
does not need to be rinsed of the soap as the
soap will mix easily with the paint. If still not
working, call factory. Disassembly of pump will
VOID the warranty.
Paint leaving nozzle in
stream, not spray
Paint too thick
Thin paint.
Spray inconsistent
Obstruction in nozzle
Remove nozzle screen. Clean or Replace.
Spray inconsistent
Obstruction or clog in pick up tube
screen
Remove pick up tube and filter screen. Filter
paint, clean screen and remove clogs.
Spray pattern too thin
or uneven
Wrong nozzle or spray head height is
incorrect.
Viscosity may be too thick
See Selection Guide. Adjust spray head height
up or down. Nozzle slot has to be horizontal to
ground.
Thin paint as per manufacturer
recommendation
Paint drips after being
shut off
Dirty or worn check ball in nozzle or gun
filter
Faulty control lever
Dissemble and clean, or replace
Replace
Please call us! If you have any questions during setup, painting or cleaning 1-800-624-6706

ECOLINER™
ALWAYS wear safety goggles or protective eye-wear when operating the unit!
1700 Jasper St., Unit F, Aurora, CO 80011 T800.624.6706 F303.364.7796 •Newstripe.com
EcoLiner™ Manual / 4483.0917
THE NEWSTRIPE WARRANTY –12 MONTH
NEWSTRIPE, INC., WARRANTS TO THE ORIGINAL PURCHASER, FOR 12 (TWELVE) MONTHS AFTER DATE
OF PURCHASE, THAT THE EQUIPMENT* HEREBY SOLD SHALL BE FREE OF DEFECTS IN MATERIALS
AND WORKMANSHIP. THIS WARRANTY DOES NOT EXTEND TO ANY DAMAGE OR MALFUNCTION
RESULTING FROM MISUSE, NEGLECT, ACCIDENT, IMPROPER OPERATION, OR NORMAL WEAR AND
TEAR.
Damage incurred in shipment from Newstripe, Inc. to the customer is the total responsibility of the carrier. The
CUSTOMER MUST NOTE DAMAGES on the Bill of Lading of Trucking Company or Railroad; and Newstripe, Inc.
will furnish to the customer the cost or parts and labor. The customer can then bill the common carrier for the damages by
placing his signature on the documents.
The Newstripe, Inc. obligation under this warranty and any implied warranties is limited to replacement or repair of
defective parts of its manufacture without charge for 12 (Twelve) months from date of purchase. For service under this
warranty, buyer shall ship the defective part or parts of the equipment, transportation prepaid, to Newstripe, Inc. together
with a written description of any claimed defect and proof of purchase date of the materials being returned. Prior to
retuning any part or machine, the CUSTOMER must obtain a Return Materials Authorization number. Call 1-
800-624-6706.
*Gasoline engines, compressors, pumps (including airless) and Transaxles are furnished with their respective
manufacturer's warranties only. Such components are not covered by any warranty of Newstripe, Inc. Where
Newstripe elects to extend manufacturers’ warranties, the warranty shall be pro-rated as to cover 100% of the cost
to replace or repair materials and parts for the first 12 months of ownership and 60% for the remaining 6 month
period.
The responsibilities described above are the only responsibilities of Newstripe, Inc. under this written warranty or any
implied warranty, and may be exercised only within 12 (Twelve) months from the date of purchase. In no event shall
Newstripe, Inc. be liable for incidental or consequential damages and no person had any authority to bind it to any
representation or warranty, not be responsible for work done, materials furnished or repairs made by others without its'
specific written authorization.
THIS WARRANTY SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND
THERE IS NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND WITH RESPECT TO THE GOODS
SOLD HEREBY EXCEPT AS SET FORTH HEREIN. IT IS EXPRESSLY AGREED THAT THIS WARRANTY
SHALL BE LIMITED TO THE ADJUSTMENT, REPAIR OR REPLACEMENT OF PARTS AND THE LABOR AND
SERVICES REQUIRED THEREBY. IN NO EVENT, INCLUDING ANY CLAIM FOR NEGLIGENCE, SHALL
NEWSTRIPE, INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Sincerely,
Newstripe, Inc