Njoy Cadu Series User manual

Cadu Series User Manual
Manual de ulizare
UPCMTLS665TCAAZ01B
UPCMTLS685TCAAZ01B
UPCMTLS610HCAAZ01B
UPCMTLS615HCAAZ01B
UPCMTLS620HCAAZ01B
Before using this product, carefully read all product documentaon and retain it for future reference.
627.36.22.0

2
The following models belong to the Cadu Series UPS:
600 VA
800 VA
1000 VA
1500 VA
2000 VA
Cadu 650
Cadu 850
Cadu 1000
Cadu 1500
Cadu 2000
Thank you for purchasing our products!
Please read this manual before using the product.
nJoy is a brand of power and backup protecon products that create
soluons for mulple levels of environment complexity, residenal
to industrial
This UPS will protect your electronic equipment from physical
damage and will provide emergency baery backup power to
prevent data loss in the event of power problems.

3
UPS unit
Power cord
USB cable
User manual
Warranty card
Package contents
Product overview
1
2
Cadu 650/850 - Front view / Back view
English
Romana
431
2 76
NOTE!
Before installaon, please inspect the unit. Be sure that nothing inside the
package is damaged. Keep the original package in a safe place for future use.
5

4
Cadu 1000 - Front view / Back view
Cadu 1500/2000 - Front view / Back view
4
4
6 3
3
1
1
2
2 5
5
7
7

5
1. LCD display: Indicate status informaon, sengs and events. It
auto-dims to 20% brightness aer 20 seconds in normal condions.
It brightens up when power buon is shortly pressed or when
abnormal condion occurs ( Baery mode, Fault & Alarm).
2. Power On/O buon: Short press Power buon for LCD brighten,
long press Power buon to turn the UPS ON or OFF.
3. Input power cord: Connect to ulity power.
4. HID USB port: Allows the UPS to appear in Windows like a baery
icon. When the power is out, you can sll see the baery level and
adjust its sengs. Also Windows power management opons are
available. In case you need more advanced local management we
recommend you to install and use “ViewPower” soware.
5. 1Gb/s Network, Modem or Phone surge protecon
6. Input circuit breaker: This provides opmal overload protecon.
7. AC outlet: The UPS provides outlets for connected equipment to
insure temporary uninterrupted operaon during a power failure
and against surges and spikes.
Important safety warnings
3
Please comply with all warnings and operang instrucons in this manual
strictly. Save this manual properly and carefully read the following
instrucons before installing the unit. Do not operate this unit before
reading through all safety informaon and operang instrucons carefully:
Transportaon
• Please transport the UPS system only in the original package to
protect against shock and impact.
Preparaon
• Condensaon may occur if the UPS system is moved directly from cold
to warm environment. The UPS system must be absolutely dry before
being installed. Please allow at least two hours for the UPS system to
acclimate to the environment.
• Do not install the UPS system near water or in moist environments.
• Do not install the UPS system where it would be exposed to direct
English
Romana

6
sunlight or near heat sources.
• Do not block venlaon holes in the UPS housing.
Installaon
• Do not connect appliances or devices which would overload the UPS
system (e.g. laser printers) to the UPS output sockets.
• Place cables in such a way that no one can step on or trip over them.
• Do not connect domesc appliances such as hair dryers to UPS output
sockets.
• The UPS can be operated by any individuals with no previous
experience.
• Connect the UPS system only to an earthed shockproof outlet which
must be easily accessible and close to the UPS system.
• Please use only VDE-tested, CE-marked mains cable (e.g. the mains
cable of your computer) to connect the UPS system to the building
wiring outlet (shockproof outlet).
• Please use only VDE-tested, CE-marked power cables to connect the
loads to the UPS system.
• When installing the equipment, it should ensure that the sum of
the leakage current of the UPS and the connected devices does not
exceed 3.5mA.
Operaon
• Do not disconnect the mains cable on the UPS system or the building
wiring outlet (shockproof socket outlet) during operaons since this
would cancel the protecve earthing of the UPS system and of all
connected loads.
• The UPS system features its own, internal current source (baeries).
The UPS output sockets or output terminals block may be electrically
live even if the UPS system is not connected to the building wiring
outlet.
• In order to fully disconnect the UPS system, rst press the OFF/Enter
buon to disconnect the mains.
• Prevent uids or other foreign objects from entering the inside of the
UPS system.
• WARNING: This is a category C2 UPS product. In a residenal

7
environment, this product may cause radio interference, in which case
the user may be required to take addional measures.
Maintenance, service and faults
• The UPS system operates with hazardous voltages. Repairs may be
carried out only by qualied maintenance personnel.
• Cauon - risk of electric shock. Even aer the unit is disconnected
from the mains (building wiring outlet), components inside the UPS
system are sll connected to the baery and electrically live and
dangerous.
• Before carrying out any kind of service and/or maintenance,
disconnect the baeries and verify that no current is present and no
hazardous voltage exists in the terminals of high capability capacitor
such as BUS-capacitors.
• Only persons are adequately familiar with baeries and with the
required precauonary measures may replace baeries and supervise
operaons. Unauthorized persons must be kept well away from the
baeries.
• Cauon - risk of electric shock. The baery circuit is not isolated
from the input voltage. Hazardous voltages may occur between the
baery terminals and the ground. Before touching, please verify that
no voltage is present!
• Baeries may cause electric shock and have a high short-circuit
current. Please take the precauonary measures specied in this
manual and any other measures necessary when working with
baeries: remove wristwatches, rings and other metal objects, use
only tools with insulated grips and handles.
• When changing baeries, install the same number and same type of
baeries.
• Do not aempt to dispose of baeries by burning them. This could
cause baery explosion.
• Do not open or destroy baeries. Escaping electrolyte can cause injury
to the skin and eyes. It may be toxic.
• Please replace the fuse only with the same type and amperage in order
to avoid re hazards.
• Do not dismantle the UPS system.
English
Romana

8
Installing your UPS system
4
4.1 Hardware installaon guide
1. Placement & Storage condions
Install the UPS in a protected area that is free of excessive dust and
has adequate air ow. Please place the UPS away from other units at
least 15 cm to avoid interference. Do NOT operate the UPS where the
temperature and humidity is outside the specic limits. (Please check the
specs for the limitaons.)
2. Connect to ulity and charging
Plug in the AC input cord to the wall outlet. For the best results, suggest
to charge the baery at least 6 hours before inial use. The unit charges
its baery while connecng to the ulity.
3. Connect the loads
Plug in the loads to output receptacles on the rear panel of the UPS.
Simply turn on the power switch of UPS unit, then devices connected to
the UPS will be protected by UPS unit.
Do NOT plug LASER
PRINTERS into any of
the outlets.
Do NOT plug any SURGE
STRIPS into any of the
outlets.
CAUTION

9
4. Connect communicaon cable
To allow for unaended UPS shutdown/start up and status monitoring,
connect the communicaon cable one end to the USB port and the other
to the communicaon port of your PC. With the monitoring soware
installed, you can schedule UPS shutdown/start up and monitor UPS
status through PC.
5. Connect Modem/Phone /Network for surge protecon
Connect a single modem/phone line into surge protected “IN” outlet
on the back panel of the UPS unit. Connect from “OUT” out let to the
computer with phone line cable.
6. Turn On/O the unit
Turn on the UPS unit by pressing the power switch. Turn o the UPS unit
by pressing again the power switch.
4.2 Soware installaon guide
Install soware: For opmal computer system protecon, install the UPS
monitoring soware from hps://www.power-soware-download.com/
viewpower.html to fully manage the UPS.
LCD display indicators
5
UPS Mode LCD display Descripon
UPS Power
on
When UPS is powered
on, it will enter this
mode for few seconds.
Standby
Mode
In standby mode,
no output power is
available.
English
Romana

10
AC Mode
When AVR is funconing, icon
will ash every second.
When the input
voltage is within
acceptable range, UPS
will provide stable AC
power to output. The
UPS will also charge
the baeries in AC
mode.
Overload in
AC mode
Icons will ash.
When overload occurs,
alarm will beep every
0.5 second.
Baery
Mode
When baery level is low, icon
will ash every second .
Alarm will beep every
10 seconds.
Self-Test
Mode
This funcon is only
acvated via soware
for the model with
communicaon port.

11
Baery
replacement
alarm
Alarm will beep every
2 seconds. Only
available for the model
with communicaon
funcon.
Overload
in baery
mode
Icons will ash.
When overload occurs,
alarm will beep every
0.5 second.
Fault mode
A fault occurs in
the UPS. Alarm will
connue beeping.
English
Romana

12
Troubleshooting6
Problem Possible cause Soluons
No LCD
display on the
front panel.
Low baery. Charge the UPS at least 6
hours.
Baery fault. Replace the baery with the
same type of baery.
The UPS is not
turned on.
Press the power switch
again to turn on the UPS.
Alarm
connuously
sounds when
the mains is
normal.
The UPS is overload.
Remove some loads rst.
Before reconnecng
equipment, please verify
that the load matches the
UPS capability specied in
the specs.
When power
fails, back
up me is
shorten.
The UPS is overload. Remove some crical load.
Baery voltage is
too low.
Charge the UPS at least 6
hours.
Baery defect. It
might be due to
high temperature
operaon
environment, or
improper operaon
to baery.
Replace the baery with the
same type of baery.
The mains is
normal, but
the unit is on
baery mode.
Power cord is loose. Reconnect the power cord
properly.
NOTE!
If any abnormal situaons occur that are not listed above, please call for
service immediately.

13
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with
separate collecon systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste.
Instead it shall be handed over to the applicable collecon point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potenal
negave consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The recycling of materials will help to conserve natural resources.
English
Romana

14
Din seria Cadu fac parte urmatoarele modele:
600 VA
800 VA
1000 VA
1500 VA
2000 VA
Cadu 650
Cadu 850
Cadu 1000
Cadu 1500
Cadu 2000
Multumim pentru ca a ales produsele noastre!
Va rugam ci cu atene manualul de ulizare inainte de a
pune in funcune acest produs.
nJoy este un brand de solui UPS dedicate protecei si
rezervei de energie din diferite medii de ulizare, de la
rezidenal la industrial.
UPS-ul va protejeaza echipamentele electronice de daune zice
si ofera o baterie de rezerva pentru a preveni pierderile de date in
cazul intreruperilor accidentale ale energiei electrice.

15
English
Romana
Unitatea UPS
Cablu de alimentare
Cablu USB
Manual de utilizare
Certificat de garantie
Connutul pachetului
Prezentarea produsului
1
2
Cadu 650/850 - Vedere din fata / Vedere din spate
431
2 76
NOTA!
Inainte de instalare inspecta unitatea. Fi siguri ca nimic din interiorul
pachetului nu este stricat. Tine pachetul original intr-un loc sigur pentru o
ulizare ulterioara.
5

16
Cadu 1000 - Vedere din fata / Vedere din spate
Cadu 1500/2000 - Vedere din fata / Vedere din spate
4
4
6 3
3
1
1
2
2 5
5
7
7

17
English
Romana
1. Asaj LCD: Indica informai despre stare, setari si evenimente.
Reduce automat luminozitatea la 20% dupa 20 de secunde in condii
normale de funconare. Se lumineaza atunci cand butonul de alimentare
este apasat scurt sau cand apare un eveniment (funconare pe mod
baterie sau avarie).
2. Buton de pornit/oprit: Apasa scurt butonul Power pentru a lumina
ecranul LCD, apasa lung butonul Power pentru pornirea sau oprirea
UPS-ului.
3. Cablu de alimentare: Conecta-l la retea.
4. Port HID USB: Permite UPS-ului sa apara in Windows ca o baterie.
In momentul intreruperii curentului ai opunea de a vedea nivelul
bateriei, care este incarcarea plus al parametrii. Se pot folosi opunile
din Windows legate de controlul bateriei. Pentru opuni exnse se
recomanda instalarea soware-ului ViewPower.
5. Protece linia de modem/telefon si retea de pana la 1Gb/s.
6. Siguranta pentru curentul de intrare: Siguranta protejeaza in caz de
supraincarcare.
7. Prize AC: UPS-ul are prize pentru conectarea echipamentelor pentru
a asigura funconarea temporara a acestora in cazul unei caderi sau
variai de tensiune.
Averzari de siguranta
3
Va rugam sa respecta toate aversmentele si instrucunile de ulizare din
acest manual. Pastra acest manual in mod corespunzator si ci cu atene
urmatoarele instrucuni inainte de instalarea aparatului. Nu folosi aceasta
unitate inainte de a ci toate instrucunile de siguranta si de ulizare cu
atene:
Transport
• Va rugam sa transporta sistemul UPS numai in ambalajul original
pentru a-l proteja impotriva socurilor.
Pregare
• Condensul poate aparea daca sistemul UPS este mutat dintr-un mediu
rece in unul cald. Sistemul UPS trebuie sa e uscat inainte de a 
instalat. Va rugam sa aloca cel pun doua ore pentru ca sistemul UPS

18
sa se aclimazeze cu mediul unde dori sa il instala.
• Nu instala sistemul UPS langa apa sau in medii umede.
• Nu instala sistemul UPS acolo unde ar  expus la lumina directa a
soarelui sau in apropierea surselor de incalzire.
• Nu bloca oriciile de venlae ale carcasei UPS-ului.
Instalare
• Nu conecta aparate sau dispozive care ar suprasolicita sistemul UPS
(de exemplu: imprimantele laser) la mufele de iesire UPS.
• Instala cablurile in asa fel incat nimeni sa nu calce pe ele.
• Nu conecta aparate de uz casnic, cum ar  uscatoare de par la prizele
de iesire UPS.
• UPS-ul poate  folosit de orice persoana, fara a necesita nici o
experienta anterioara.
• Conecta sistemul UPS numai la o priza cu impamantare, care trebuie
sa e usor accesibila si aproape de sistemul UPS.
• Va rugam sa folosi numai cabluri de alimentare testate VDE si cu
marcaj CE (de exemplu: cablul de alimentare de la computer) pentru a
conecta sistemul UPS.
• La instalarea echipamentului, trebuie sa va asigura ca totalul
curentului de scurgere al UPS si al dispozivelor conectate nu
depaseste 3,5 mA.
Operare
• Nu deconecta cablul de alimentare de la sistemul UPS sau de la priza
cladirii in mpul ulizarii, deoarece acest lucru ar anula impamantarea
de protece a sistemului UPS si a tuturor sarcinilor conectate.
• Sistemul UPS are propria sursa de curent intern (baterii). Prizele de
iesire sau terminale de iesire pe categorii pot  incarcate electric, chiar
daca sistemul UPS nu este conectat la sistemul electric al cladirii.
• Pentru a deconecta complet sistemul UPS, apasa mai intai butonul
OFF/Enter pentru a deconecta sursa de alimentare.
• Nu lasa sa ajunga in interiorul unitai UPS orice obiect strain sau lichide.
• ATENTIE: Acesta este un produs UPS de clasa C2. In mediul casnic, acest
produs poate cauza interferenţe radio, caz cand poate  necesar sa se ia

19
English
Romana
masuri suplimentare.
Intrenere, service si defecte
• Sistemul UPS funconeaza cu tensiuni periculoase. Reparaile pot 
efectuate numai de catre personalul de intrenere calicat.
• Atene - risc de soc electric. Chiar si dupa ce aparatul este deconectat
de la reteaua electrica, componentele din interiorul sistemului UPS
sunt inca conectate la baterie si sunt incarcate electric si periculoase.
• Inainte de a efectua orice fel de service si / sau intrenere, deconecta
bateriile si verica sa nu existe curent sau tensiune periculoasa
in terminalele condensatorului de mare capacitate, cum ar 
condensatorul BUS.
• Numai persoanele care sunt familiarizate in mod adecvat cu baterii si
cu masurile de precaue necesare pot inlocui bateriile si supraveghea
operaunile. Persoane neautorizate trebuie sa e nute departe de
baterii sistemului UPS.
• Atene - risc de soc electric. Circuitul bateriei nu este izolat de
tensiunea de intrare. Tensiuni periculoase pot aparea intre bornele
bateriei si pamant. Inainte de a ange, va rugam sa verica ca nu
exista tensiune!
• Bateriile pot provoca soc electric. Va rugam sa lua masurile de
precaue specicate mai jos, precum si orice alte masuri necesare
atunci cand se lucreaza cu bateriile sistemului: da-va jos ceasurile
de mana, inelele si alte obiecte metalice si folosi doar instrumente cu
manere izolate.
• La schimbarea bateriilor, instala acelasi numar si acelasi p de baterii.
• Nu incerca sa distruge bateriile prin arderea lor. Acest lucru poate
cauza explozia bateriilor.
• Nu deschide sau distruge bateriile. Scurgerea electrolilor poate
provoca leziuni la nivelul pielii si ochilor si poate  toxic.
• Va rugam sa inlocui siguranta numai cu acelasi p de siguranta si
amperaj pentru a evita pericolele de incendiu.
• Nu dezasambla sistemul UPS.

20
Instalarea sistemului de UPS
4
4.1 Ghid de instalare Hardware
1. Condii de depozitare
Instala UPS-ul intr-o zona lipsita de praf si aerisita. Va rugam aseza
UPS-ul la cel pun 15 de cm de alte echipamente pentru a evita orice fel
de interferente. Nu pune in funcune UPS-ul in condii de umiditate si
temperatura ridicate (Consulta specicaile pentru limitari).
2. Conectarea la retea si incarcarea
Conecta cablul de alimentare la priza din perete. Pentru o funconare
fara cusur, incarca bateriile pentru cel pun 6 ore inainte de prima
ulizare. UPS-ul se incarca automat cat este conectat la retea.
3. Conecta echipamentele
Conecta echipamentele la prizele UPS-ului de pe panoul din spate.
Porni UPS-ul de la butonul de ON, iar echipamentele conectate vor 
protejate.
NU conecta
imprimante laser la
nici una din prizele
UPS-ului.
NU conecta alte
ACCESORII CU
PROTECTIE la
niciuna din prize.
ATENTIE