NordicTrack FREESTRIDER 35 S User manual

Model No. NTSR01309.0
Serial No.
Write the serial number in the space
above for reference.
USERʼS MANUA
Serial
Number
Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
www.nordictrack.com
QUESTIONS?
f you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CA TO -FREE:
1-888-825-2588
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.nordictrackservice.com

2
TAB E OF CONTENTS
WARNNGDECALPLACEMENT ..............................................................2
MPORTANTPRECAUTONS ................................................................3
BEFOREYOUBEGN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLPTCALSTRDER .....................................................11
MANTENANCEANDTROUBLESHOOTNG ...................................................17
EXERCSEGUDELNES ...................................................................18
PARTLST ..............................................................................19
EXPLODEDDRAWNG ....................................................................21
HOWTOCONTACTCUSTOMERCARE ...............................................BackCover
LMTEDWARRANTY ..............................................................BackCover
NordicTrack is a registered trademark of CON P, nc.
WARNING DECA P ACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical strider before using your elliptical
strider. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical strider are ade-
quately informed of all precautions.
3. The elliptical strider is intended for home
use only. Do not use the elliptical strider in a
commercial, rental, or institutional setting.
4. Keep the elliptical strider indoors, away from
moisture and dust. Place the elliptical strider
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 3 ft. (0.9 m) of clearance in
the front and rear of your elliptical strider
and 2 ft. (0.6 m) on each side.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical strider at all times.
7. The elliptical strider should not be used by
persons weighing more than 300 lbs.
(136 kg).
8. Wear appropriate exercise clothes while
using the elliptical strider. Always wear ath-
letic shoes for foot protection while
exercising.
9. Hold the handlebars or the handrails when
mounting, dismounting, or using the ellipti-
cal strider.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
11. Keep your back straight while using the
elliptical strider; do not arch your back.
12. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
14. Use the elliptical strider only as described in
this manual.

4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
NordicTrack®FREESTR DER 35 S elliptical strider.
The FREESTR DER 35 S elliptical strider provides a
wide array of features designed to make your work-
outs more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical strider. f you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handrail
Wheel
Pedal
Console
Accessory Tray
Leveling Foot
Handlebar
Handgrip Pulse Sensor
Fan

5
ASSEMB Y
Assembly requires two persons. Place all parts of the elliptical strider in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver .
As you assemble the elliptical strider, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART L ST near the end of this manual. The number
following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit,
check to see if it has been preassembled.
3/8" x 1" Patch
Screw (122)–4
3/8" x 3/4" Patch
Screw (123)–2
3/8" x 3" Screw
(124)–2
M10 Split
Washer (128)–2
#8 x 3/4"
Screw (86)–16
#8 x 1" Tek
Screw (126)–8
#8 x 35mm
Screw (125)–1

6
1.
IMPORTANT: Do not remove the foam block
(not shown) located under the pedals until
you have completed step 2.
dentify the Shield Cap (5) and the Upright (26)
and orient them as shown. Slide the Shield Cap
upward around the Upright.
While another person holds the Upright (26)
near the Frame (1), locate the wire ties in the
Upright.
See the inset drawing. Tie the lower end of a
wire tie to the end of the Wire Harness (77).
Pull the other end of the wire tie upward out of
the top of the Upright (26).
Next, tie the lower end of the other wire tie to
the end of the Power Cable (81). Pull the other
end of the wire tie upward out of the top of the
Upright (26).
Then, untie and discard the wire ties.
1
5
1
Wire
Ties
77
26
77
81
Wire
Ties
2. Tip: Avoid pinching the wires. Attach the
Upright (26) to the Frame (1) with four 3/8" x 1"
Patch Screws (122). Note: Two of the Patch
Screws may be preattached to the Frame. Tip:
Start all the Patch Screws before tightening
any of them.
Remove and discard the foam block (not
shown) located under the pedals.
2
122
122
26
Avoid pinching
the wires
To make assembly easier, read the
information on page 5 before you begin.
81
1

7
3. Slide the Shield Cap (5) downward over the
Right and Left Shields (6, 7).
Attach the Shield Cap (5) with a #8 x 35mm
Screw (125) and two #8 x 3/4" Screws (86).
Tip: Start all the Screws before tightening
any of them.
3
86
86
6
125
5
7
4. Orient the Accessory Tray (18) as shown. Press
the Accessory Tray into the Shield Cap (5). 4
5
18

8
5. dentify the Right Handrail (69), which is marked
with a “Right” sticker.
While another person holds the Right Handrail
(69) near the Upright (26), connect the right
Pulse Wire (78) to the right Sensor Wire (79).
nsert the excess wire into the Right Handrail
(69). Then, slide the Right Handrail onto the
Upright (26).
Tip: Avoid pinching the wires. Attach the
Right Handrail (69) with a 3/8" x 3/4" Patch
Screw (123) and an M10 Split Washer (128).
Do not tighten the Patch Screw yet.
Repeat this step for the eft Handrail (70).
5
69
128
123
79
26
70
78
30
6. IMPORTANT: To prevent damage, do not
allow the elliptical strider to tip to either side
during this step.
While another person lifts the rear of the Frame
(1) in the location shown by the arrow, attach
each Handrail (69, 70) to the Frame with a 3/8"
x 3" Screw (124).
See step 5. Tighten the 3/8" x 3/4" Patch
Screws (123).
6
124
124
69
1
70
Avoid pinching
the wires

9
7. While another person holds the Console (4)
near the Upright (26), connect the wires on the
Console to the Wire Harness (77), the Power
Cable (81), the Ground Wire (82), and the Pulse
Wires (78).
nsert the excess wire downward into the
Upright (26).
Tip: Avoid pinching the wires. Attach the
Console (4) to the Upright (26) with four #8 x
3/4" Screws (86).
7
86
77
81
82
26
78
4
8. dentify the Front and Rear Shields (10, 13) and
orient them as shown.
Attach the Front and Rear Shields (10, 13)
around the Upright (26) with six #8 x 3/4"
Screws (86).
8
26
13
10
86
Avoid pinching
the wires

10
14
86
20
21
9. dentify the Right Upper and Lower Covers (14,
15), which are marked with “Right” stickers, and
orient them as shown.
Attach the Right Upper and Lower Covers (14,
15) around the Right Handlebar (20) with two
#8 x 3/4" Screws (86).
Repeat this step for the eft Handlebar (21).
9
15
10. dentify a set of Right and Left Link Covers (22,
23), which are marked with “Right” and “Left”
stickers, and orient them as shown.
Attach the Right and Left Link Covers (22, 23)
around the Right Handlebar (20) with four #8 x
1" Tek Screws (126).
Repeat this step for the other side of the
elliptical strider.
20
126
126
23
22
12. Make sure that all parts are properly tightened before you use the elliptical strider. Note: After assembly
is completed, some extra parts may be left over. Place a mat beneath the elliptical strider to protect the floor.
11. Plug the AC Power Adapter (76) into the jack on
the front of the elliptical strider.
To plug the AC Power Adapter (76) into an out-
let, see HOW TO PLUG N THE POWER
ADAPTER on page 11.
76
10
11