NXP Semiconductors UM11733 User manual

UM11733
Hardware user manual for FRDM665CANFDEVB
Rev. 1 — 25 July 2022 User manual
Document information
Information Content
Keywords MC33665A, CAN FD, BMS gateway IC
Abstract Hardware user manual for FRDM665CANFDEVB, which can support both
CAN and CAN FD communication to microcontroller on battery control unit
(BCU).

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
Rev Date Description
1 20220725 initial version
Revision history
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
2 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
IMPORTANT NOTICE
For engineering development or evaluation purposes only
NXP provides the product under the following conditions:
This evaluation kit is for use of ENGINEERING DEVELOPMENT OR
EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldere
d to a printed-circuit board to make it easier to access inputs, outputs
and supply terminals. This evaluation board may be used with any
development system or other source of I/O signals by connecting it to the
host MCU computer board via off-the-shelf cables. This evaluation board
is not a Reference Design and is not intended to represent a final design
recommendation for any particular application. Final device in an application
heavily depends on proper printed-circuit board layout and heat sinking
design as well as attention to supply filtering, transient suppression, and I/O
signal quality.
The product provided may not be complete in terms of required design,
marketing, and or manufacturing related protective considerations, including
product safety measures typically found in the end device incorporating the
product. Due to the open construction of the product, it is the responsibility of
the user to take all appropriate precautions for electric discharge. In order to
minimize risks associated with the customers’ applications, adequate design
and operating safeguards must be provided by the customer to minimize
inherent or procedural hazards. For any safety concerns, contact NXP sales
and technical support services.
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
3 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
1 Introduction
The NXP analog product development boards provide an easy-to-use platform for
evaluating NXP products. The boards support a range of analog, mixed-signal, and
power solutions. They incorporate monolithic integrated circuits and system-in-package
devices that use proven high-volume technology. NXP products offer longer battery life, a
smaller form factor, reduced component counts, lower cost, and improved performance in
powering state-of-the-art systems.
2 Finding kit resources and information on the NXP web site
NXP Semiconductors provides online resources for this evaluation board and its
supported device(s) on http://www.nxp.com.
The information page for the FRDM665CANFDEVB evaluation board is at http://
www.nxp.com/FRDM665CANFDEVB. The information page provides overview
information, documentation, software and tools, parametrics, ordering information and
a Getting Started tab. The Getting Started tab provides quick-reference information
applicable to using the FRDM665CANFDEVB evaluation board, including the
downloadable assets referenced in this document.
3 Getting ready
Working with the FRDM665CANFDEVB evaluation board requires the kit contents,
additional hardware, and a Windows PC workstation with installed software.
3.1 Kit contents
The FRDM665CANFDEVB kit includes:
•MC33665A CAN FD EVB, CAN or CAN FD to four transformer physical layer (TPL)
interface EVB
•One TPL daisy chain cable; two-wire twisted-pair daisy chain interface cable
•One power cable, 4-pin socket
•Quick start guide
3.2 Additional hardware
In addition to the kit contents, the following hardware is necessary or beneficial:
•External dual power supply 8 V to 16 V/2 A (optional)
•EVBs of battery cell controller (BCC) devices from NXP
•14-cell battery pack or a battery emulator, such as BATT-14CEMULATOR
4 Getting to know the hardware
4.1 Kit overview
The FRDM665CANFDEVB serves as a hardware evaluation tool in support of the
MC33665A device of NXP. The MC33665A is a gateway router that can route TPL
messages from the microcontroller to four different TPL ports. It is designed for use in
both automotive and industrial applications. The device can route both TPL2 and TPL3
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
4 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
messages. FRDM665CANFDEVB is an ideal board for rapid prototyping of MC33665A
for CAN FD interface to MCU.
FRDM665CANFDEVB supports both classical CAN or CAN FD. Differential
communication to daisy chain devices can be established with four different ports.
4.2 Board features
The main features of FRDM665CANFDEVB are:
•CAN and CAN FD
•Onboard transformer isolation for TPL communication to BCC devices
•Configurable VIO voltage
•Configurable VDD5V from internal and external supply
•DIP switch for configuring the arbitration baud rate and CAN ID of MC33665A
•Reset switch for the device and board
•LED display for the status of power
•Connectors for external interface to general-purpose input/output (GPIO) and I2C-bus
4.3 Block diagram
aaa-044810
CAN TX
REQUEST
CAN
TRANSCEIVER
VIO(VDDIO)
CFG0, CFG1
ID0_STB_OD, ID1, ID2, ID3
DIP switch
3V3LDO
J13 J8
SW1
J1
D12
CAN RX
RESPONSE
TPL
PORT 0
LDO
MC33665A
POWER MANAGEMENT
GPIO, CONFIG AND
STATUS PINS
POR
T
0
CAN
TPL
PORT 1
PORT 1
TPL
PORT 2
PORT 2
TPL
PORT 3
reset
switch
PORT 3
VBAT
KL30/
12 V/T30
VDD5V VREG
VDDC/VDDD
VDD5V
VREG
VREG
EXT5V
external interface
for GPIO and
status signals
Figure 1. FRDM665CANFDEVB block diagram
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
5 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
4.4 Board description
The FRDM665CANFDEVB allows the user to prototype and test all functions of the
MC33665A gateway router with CAN or CAN FD communication.
CAN or CAN FD communication can be established with MC33665A via sub-D9
connector. In addition to sub-D9 CAN connector, same signals of CANH and CANL are
available in both power and CAN connector J6 and CANEVB interface J10. TJA1443 is
the CAN transceiver used for FRDM665CANFDEVB.
12 V (> 5 W) DC power supply can be connected to J6. VDD5V selection and VIO
selection have no influence in FRDM665CANFDEVB as there is a constant 12 V power
supply and there is no direct microcontroller to select VIO. CAN ID can be selected by
setting the position in DIP switch SW2. Take care to set the position of DIP switches
(SW2) appropriately to configure ID and CAN arbitration baud rates to MC33665A.
External 5 V can be connected to bypass the VREG circuit of MC33665A. Take care in
selecting the appropriate jumper J8 to power the VDD5V.
Connector J1 gives the option to access the GPIO and I2C pins of MC33665A.
Contact the NXP engineering team for using TPL autowake function in
FRDM665CANFDEVB.
Figure 2. CAN FD EVB description
Power configuration of the board can be reflected by LEDs populated on board. LEDs
glowing on board reflect the right power interface connected to FRDM665CANFDEVB.
LED VBAT 12 V External 5 V
D13 - red X -
D14 - green X X
D15 - green X X
Table 1. Power status LEDs
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
6 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
LED VBAT 12 V External 5 V
D16 - red X -
Table 1. Power status LEDs...continued
4.5 Connectors
FRDM665CANFDEVB has multiple connectors for interfacing to MCU, internal GPIO,
and external BCC devices.
Figure 3. FRDM665CANFDEVB connectors
Pin configuration of connectors is shown in Table 2 to Table 8.
Pin number Connection Description
1 VBAT connection to 12 V
2 CANH CANH interface for TJA1443
3 CANL CANL interface for TJA1443
4 GND ground connection for MC33665A and interface boards
Table 2. Power and CAN connector - J6
Pin number Connection Description
1 CANH CANH interface for TJA1443
2 CANL CANL interface for TJA1443
3 GND ground connection for MC33665A and interface boards
4 - no connection
Table 3. CANEVB connector - J10
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
7 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
Pin number Connection Description
1 GPIO0 interface to GPIO0 or INT0 for MC33665A
2 GPIO1 interface to GPIO1 or INT1 for MC33665A
3 GPIO2 interface to GPIO2 or INT2 for MC33665A
4 GPIO3 interface to GPIO3 or INT3 for MC33665A
5 GPIO4 interface to GPIO4 or I2C-bus in MC33665A
6 GPIO5 interface to GPIO5 or I2C-bus in MC33665A
7 GPIO6 interface to GPIO6 or SYNC in MC33665A
8 GPIO7 interface to GPIO7 or HOLD in MC33665A
9 VSS/GND ground
10 VDD5V 5 V supply line
11 VSS/GND ground
12 VIO VIO interface for MC33665A
13 - not connected
14 - not connected
15 NC-CAN_TXD populate R6 to connect CAN_TXD
16 NC-CAN_RXD populate R7 to connect CAN_RXD
17 STB_N_OUT inverted standby signal from MC33665A
18 STB_OUT standby signal from MC33665A
19 RESET reset signal for MC33665A
20 VDD5V 5 V supply line
Table 4. GPIO and interface - J1
Pin number Connection Description
1 EXT5V external 5 V supply
2 VSS/GND ground
Table 5. External 5 V - J11
Pin number Connection Description
1-2 VREG-VDD5V Connection from VREG generated by internal low dropout (LDO) connection to
VDD5V for MC33665A and interface circuits. Note: Default connection.
2-3 EXT5V-VDD5V External 5 V supply can be connected to VDD5V to MC33665A and interface circuits.
Table 6. VDD5V jumper - J8
Pin number Connection Description
1-2 VREG-VIO connect VREG (5 V) generated by internal LDO of MC33665A to VDDIO/VIO of
MC33665A and interface circuit. Note: Default connection.
Table 7. VIO jumper - J13
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
8 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
Pin number Connection Description
2-3 3V3LDO-VIO connect constant 3.3 V generated by external LDO to VIO
Table 7. VIO jumper - J13...continued
Pin number Connection Description
2 CANL CANL interface for TJA1443
3 VSS ground connection for MC33665A and interface boards
7 CANH CANH interface for TJA1443
Others - not connected
Table 8. Sub-D9 CAN connector - J15
4.6 Schematic, board layout and bill of materials
The schematic, board layout and bill of materials for the FRDM665CANFDEVB
evaluation board are available at http://www.nxp.com/FRDM665CANFDEVB
5 Configuring the hardware
FRDM665CANFDEVB can be configured as stacked board to S32K344EVB.
5.1 CAN FD interface
FRDM665CANFDEVB can be connected to a PC/laptop or other ECUs with
power and CAN cable or connector. 12 V supply line can be used to power the
FRDM665CANFDEVB, female sub-D9 connector can be interfaced to relevant CAN tool
or ECU. SW2 can be used to configure the CAN ID for MC33665A. CFG pins can also be
configured to set the arbitration speed for MC33665A. Press SW1 button (RST switch)
after changing any settings on SW2 (ID and CFG). Ensure the settings on J8 for VDD5V
and J13 for VIO selection are appropriate for power supplied to the board. CANEVB
interface J10 can be used for direct interface with S32K344EVB for CAN or CAN FD.
Figure 4. CAN FD EVB interface
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
9 / 13

NXP Semiconductors UM11733
Hardware user manual for FRDM665CANFDEVB
6 Available accessories
Part number Description
FRDM33772CSPEVB evaluation board for MC33772C with SPI communication
RD33771CDSTEVB evaluation board for MC33771C BCC with isolated daisy chain communication
BATT-14EXTENDER battery emulator extender
BATT-14CEMULATOR 14-cell battery pack to supply MC33771C EVBs
BATT-TPLCABLE20 TPL, two-wire, twisted, 20 cm long cable
BATT-TPLCABLE50 TPL, two-wire, twisted, 50 cm long cable
BATT-14CTCABLE25 cell terminal (CT) cable, 14 cells, 25 cm long
Table 9. Accessories
UM11733 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved.
User manual Rev. 1 — 25 July 2022
10 / 13