Oce OP30C User manual

1.1.1.
Océ OP30C Printing System Functions
Operations Guide
Education Services
Océ
Operations Guide
Englishversion

Operation Guide
P
Introduction
Printer-related operation
■1. Features of this Printer
■2. Printer Settings
■3. Paper size setting for manual feed
(for printer use)
■4. e-MPS Functions
■5. Hard Disk/ RAM Disk
■6. Memory Card
■7. Printer Control Commands
■8. Troubleshooting
Software-related operation
■9. Procedure for Installing and Printing
with a Printer Driver
■10. Windows KX Driver
■11. Printer Driver for Macintosh

i
Trademark Information
• PRESCRIBE and ECOSYS are registered trademarks of Kyocera Corporation.
• KPDL and KIR are trademarks of Kyocera Corporation.
• Microsoft, MS-DOS, Windows and WindowsNT are registered trademarks of Microsoft Corporation of America and other countries.
• WINDOWS ME is a trademark of Microsoft Corporation.
• PCL and PJL are registered trademarks of Hewlett-Packard Company.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Ethernet is a registered trademark of Xerox Corporation.
• Novell and NetWare are registered trademarks of Novell, Inc.
• Centronics is a trademark of Centronics Data Computer Corporation.
• IBM and IBM PC-AT are trademarks of International Business Machines Corporation.
• PowerPC and Microdrive are trademarks of International Business Machines Corporation of America and other corporations.
• TrueType and Macintosh are registered trademarks of Apple Computer, Inc.
• AppleTalk is a trademark of Apple Computer, Inc.
• CompactFlash and CF are trademarks of SanDisk Corporation of America.
• This product was developed using Tornado, the real-time operating system (ROTS) general development environment from Wind River Systems, Inc.
• This printer uses PeerlessPrintXL, a PCL compatibility system developed by Peerless Group, to emulate the HP LaserJet Printer Control Language
(PCL6). PeerlessPrintXL is a trademark of Peerless Group (Redondo Beach, CA 90278, U.S.A.).
• Contains UFSTTM and MicroType®from Agfa Corporation.
All other company and product names contained in this Operation Guide are trademarks or registered trademarks of their respective companies.The
designations ™ and ® will not be used in this Operation Guide.
Introduction
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in
writing from the Publisher.
Legal Restriction On Copying
• It may be prohibited to copy copyrighted material without permission of the copyright owner.
• It is prohibited under any circumstances to copy domestic or foreign currencies.
• Copying other items may be prohibited.
About this Operation Guide
This Operation Guide is included with your Printing System (P) and should be read in combination with the Operation Guide <Set-Up
Edition> for that product.
This Operation Guide contains information on making settings in your printer, as well as on installing and setting the printing proper-
ties for the corresponding Printer Drivers.
The explanations in this Operation Guide were written with the assumption that the user has a basic understanding of how to work in
Microsoft Windows. For further information on using Windows, refer to your Microsoft Windows manual.
NOTE:
This Operation Guide contains information that corresponds to using both the inch and metric versions of this printer. When the difference in a
message is only one of upper- and lower-case spelling, we have listed the information as it specifically pertains to the inch version of this machine.
When there is even a slight difference in the message, we have listed the information for the inch version followed, in brackets, by the corresponding
information for the metric version.

ii
IBM PROGRAM LICENSE AGREEMENT
THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG
TO INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”).THIS DOCUMENT DEFINES THETERMS AND CONDITIONS
UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND
CONDITIONS OF THIS LICENSE, THEN WITHIN 14 DAYS AFTERYOUR ACQUISITION OFTHE DEVICEYOU MAY RETURN THE
DEVICE FOR A FULL REFUND.IFYOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS, THENYOU WILL BE ASSUMED
TO HAVE AGREED TO THESE TERMS AND CONDITIONS.
The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in
the country where you acquired the Programs.You obtain no rights other than those granted you under this license.
The term “Programs” means the original and all whole or partial copies of it, including modified copies or portions merged into other
programs. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.
1. License
Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the
Programs and the device to another party. If you transfer the Programs, you must transfer a copy of this license and any other
documentation to the other party.Your license is then terminated. The other party agrees to these terms and conditions by its first use
of the Program.
You may not:
1) use, copy, modify, merge, or transfer copies of the Program except as provided in this license;
2) reverse assemble or reverse compile the Program; or
3) sublicense, rent, lease, or assign the Program.
2. Limited Warranty
The Programs are provided “AS IS.”
THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS (OR CONDITIONS), EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.
SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLING AND DISTRIBUTION FOR ALDC
3. Limitation of Remedies
IBM’s entire liability under this license is the following;
1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM’s liability will be for
actual damages only and will be limited to the greater of ;
a) the equivalent of U.S.$25,000 in your local currency; or
b) IBM’s then generally available license fee for the Program
This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable.
IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if
IBM, or its authorized supplier, has been advised of the possibility of such damages. IBM will not be liable for any damages claimed
by you based on any third party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. IBM's
and the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this Section. Some
jurisdictions do not allow these limitations or exclusions, so they may not apply to you.
4. General
You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this
license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including
personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after
the cause of action arose. If you acquired the Program in the United States, this license is governed by the laws of the State of New
York. If you acquired the Program in Canada, this license is governed by the laws of the Province of Ontario. Otherwise, this license
is governed by the laws of the country in which you acquired the Program.

iii
Typeface Trademark Acknowledgement
All resident fonts in this printer are licensed from Agfa Corporation.
Helvetica, Palatino and Times are registered trademarks of Linotype-Hell AG.
ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC Zapf Dingbats are registered trademarks of International
Typeface
Corporation.
Agfa Japan License Agreement
1. “Software” shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as well as
the UFST Software.
2. You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and versions of
letters, numerals, characters and symbols (“Typefaces”) solely for your own customary business. Agfa Japan retains all rights,
title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on
the terms expressly set forth in this Agreement.
3. To protect proprietary rights of Agfa Japan, you agree to maintain the Software and other proprietary information concerning
the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and
Typefaces.
4. You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy.
5. This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License may be
terminated by Agfa Japan if you fail to comply with the terms of this License and such failure is not remedied within thirty (30)
days after notice from Agfa Japan. When this License expires or is terminated, you shall either return to Agfa Japan or destroy
all copies of the Software and Typefaces and documentation as requested.
6. You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software.
7. Agfa Japan warrants that for ninety (90) days after delivery, the Software will perform in accordance with Agfa Japan-published
specifications. Agfa Japan does not warrant that the Software is free from all bugs, errors and omissions. THE PARTIES
AGREE THAT ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY, ARE EXCLUDED.
8. Your exclusive remedy and the sole liability of Agfa Japan in connection with the Software and Typefaces is repair or
replacement of defective parts, upon their return to Agfa Japan. IN NO EVENT WILL AGFA JAPAN BE LIABLE FOR LOST
PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY
ABUSE OR MISAPPLICATION OF THE SOFTWARE AND TYPEFACES.
9. New York, U.S.A. law governs this Agreement.
10. You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written consent of
Agfa Japan.
11. Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and
Computer Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use,
duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2).
12. YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS
TERMS AND CONDITIONS. NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT
CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED
BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY.

1-1
1. Printer Settings (15 ppm copier)
1. Features of the Printer
This printer comes equipped with the following features.
KIR (Kyocera Image Refinement)
A smoothing function exclusive to Kyocera. This function uses software to increase the resolution of the printer and ensure high-quality printing. The
factory default setting for this function is “ON”. (This function is available for black and white printing only.)
High-Speed Printing
The printing speed can reach up to 30 pages per minute (11" x 8 1/2" [A4]) for black and white printing and up to 8 pages per minute (11" x 8 1/2" [A4])
for full color printing. (These speeds are applicable when making multiple copies of the same document. Actual printing speed will differ depending
upon the content of the print job.)
Media type selection
If different types of copying media (standard copy paper, OHP transparency film, label sheets, etc.) are set in the various locations for paper feed, the
printer will automatically select the type of paper that was designated for that particular print job.
EcoPrint
This printer comes equipped with an EcoPrint function that enables the reduction of toner consumption. By using the EcoPrint function, the same
quantity of toner will last longer. (This function is available for black and white printing only.)
Two-Way Parallel Interface
Data transfer from your computer to the printer is accomplished using an IEEE 1284 parallel interface.
Printer Control Commands
This printer has built-in Printer Control Commands (PRESCRIBE) with improved graphic functionality. A simple command will enable you to change
the margin setting, the character- or line-spacing, to rotate or fill in outlined fonts and graphics, and much more.
e-MPS Functions
This printer comes equipped with e-MPS (enhanced-Multiple Printing System) functions. With these functions, document data can be stored on the
Hard Disk (option) that is installed in the printer and printed out afterwards using the printer's operation panel. Available e-MPS functions include Quick
Copy, Proof and Hold, Private Print, Stored Job Printing (Job Storage), Virtual Mailbox (VMB), Temporary/Permanent Code Job and Electronic
Sorting.
Hard Disk
The optional Hard Disk can be installed in the printer. By installing the optional Hard Disk in your printer, you will be able to use the available e-MPS
functions as well as increase the efficiency of your printer with electronic sorting.
Memory (Compact Flash) Card Slot
The optional Memory Card can be installed in the printer. By installing the optional Memory Card in your printer, you will be able to use the optional
fonts, macro, and form functions, etc.

2-1
2. Printer Settings
2. Printer Settings
2-1 Procedure for making settings
1
2
3
4
Press the Printer key. The machine will switch to the printer mode.
Use the “M”and “N”cursor keys to select “MENU”and then press the Enter key.
5
Change the desired setting.
(Refer to “2-3 List of settings”on page 2-7 for information regarding each item and its
possible settings.)
Note
Settings are normally changed (turned ON and OFF, etc.) by using the “M”and “N”
cursor keys to move the selection cursor (e) and select the desired setting, and then
pressing the Enter key.
When it is necessary to type in a value or number directly (such as with a network
address or the time, etc.), use the numeric keys to enter the desired information and
the cursor left and right keys to change the location of the cursor. Once entry is
complete, press the Enter key.
Press the Copier key to switch back to the copier mode.
Select the desired setting.
(Refer to “2-2 Menu flow chart”on page 2-3 for a list of the various possible settings.)
Note
Settings are categorized into a hierarchy under the “MENU”command. Use the “M”
and “N”cursor keys to select “MENU”and then press the Enter key to access the
menu of available setting items. Once the desired setting is selected, press the Enter
key once again.
Inch specification
Metric specification
Inch specification
Metric specification
Inch specification
Metric specification
Inch specification
Metric specification

2-2
2. Printer Settings
■ Operation keys
<Inch version>
<Metric version>

2-3
2. Printer Settings
MENU Printer Status Page print out ....................................................................................................................
e-MPS functions
Quick Copy Job print out ...................................................................................................
Private Print / Stored Job print out ....................................................................................
Virtual Mailbox data print out .............................................................................................
Virtual Mailbox List print out ..............................................................................................
Code Job List print out ......................................................................................................
e-MPS settings
Maximum number of jobs stored for Quick Copy ........................................
Temporary code job partition ......................................................................
Permanent code job partition ......................................................................
Virtual Mailbox partition ..............................................................................
Interface selection ....................................................................................................................................
Parallel setting
Parallel TX/RX mode...................................................................................
Serial settings
Baud rate ....................................................................................................
Data bits......................................................................................................
Stop bit........................................................................................................
Parity ...........................................................................................................
Protocol.......................................................................................................
Barcode mode ............................................................................................
Option 1 (Network Card) settings
NetWare ON/OFF .......................................................................................
NetWare frame type .............................................................
TCP/IP ON/OFF..........................................................................................
DHCP ON/OFF ....................................................................
IP address ............................................................................
Subnet Mask ........................................................................
Gateway address .................................................................
EtherTalk ON/OFF ......................................................................................
Network Card Status Page print out ON/OFF .............................................
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2-2 Menu flow chart

2-4
2. Printer Settings
Emulation protocol ...................................................................................................................................
PCL 5c
Code set selection ......................................................................................
KC-GL
Pen (1 - 8) settings......................................................................................
Pen thickness .......................................................................
Pen color ..............................................................................
Page set ......................................................................................................
KPDL
KPDL Error Report print out ON/OFF .........................................................
KPDL(AUTO)
Auto emulation switching ............................................................................
KPDL Error Report print out ON/OFF .........................................................
Font settings
Internal
Font selection .............................................................................................
Courier font .................................................................................................
Letter Gothic font ........................................................................................
Font List print out ........................................................................................
Option
Font selection .............................................................................................
Font List print out ........................................................................................
Printing environment settings
Number of copies ..............................................................................................................
Printing orientation ............................................................................................................
Page Protect ......................................................................................................................
Line Feed (LF) handling ....................................................................................................
Carriage Return (CR) handling .........................................................................................
Printing resolution settings
Smoothing ON/OFF..........................................................................................................
EcoPrint ON/OFF ..............................................................................................................
Tone ...................................................................................................................................
Gloss mode .......................................................................................................................
28
29
30
31
32
33
34
35
34
36
37
38
39
36
39
40
41
42
43
44
45
46
47
48

2-5
2. Printer Settings
Hard Disk settings
Reading data .....................................................................................................................
Reading program data .......................................................................................................
Writing data .......................................................................................................................
Deleting data .....................................................................................................................
Deleting font data ..............................................................................................................
Deleting program data .......................................................................................................
Deleting macro data ..........................................................................................................
Formatting Hard Disk ........................................................................................................
Partition List print out .........................................................................................................
RAM disk ON/OFF ...................................................................................................................................
RAM disk size ....................................................................................................................
Reading data .....................................................................................................................
Reading program data .......................................................................................................
Writing data .......................................................................................................................
Deleting data .....................................................................................................................
Deleting font data ..............................................................................................................
Deleting program data .......................................................................................................
Deleting macro data ..........................................................................................................
Partition List print out .........................................................................................................
Memory Card settings
Reading fonts ....................................................................................................................
Reading macro data ..........................................................................................................
Reading data .....................................................................................................................
Reading program data .......................................................................................................
Writing data .......................................................................................................................
Deleting data .....................................................................................................................
Deleting font data ..............................................................................................................
Deleting program data .......................................................................................................
Deleting macro data ..........................................................................................................
Formatting the Memory Card ............................................................................................
Partition List print out .........................................................................................................
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78

2-6
2. Printer Settings
Paper handling settings
Bypass mode .....................................................................................................................
Bypass paper type .............................................................................................................
Paper source selection ......................................................................................................
Duplex mode .....................................................................................................................
Eject location selection ......................................................................................................
A4 & Letter usage ON/OFF ...............................................................................................
Custom paper type
Custom type (1 - 8) .....................................................................................
Paper thickness ....................................................................
Fuser temperature control ....................................................
Duplex printing ON/OFF.......................................................
Reset custom paper type settings .....................................................................................
Color mode selection (color / black and white print out) ..........................................................................
Color matching
RGB simulation ...........................................................................................
Ink simulation ..............................................................................................
Other settings
Form feed time-out ............................................................................................................
Receive dump mode .........................................................................................................
Printer reset .......................................................................................................................
Resource protect mode .....................................................................................................
Auto Continue ON/OFF .....................................................................................................
Recovery time for Auto Continue ................................................................
Service
Service Rep Status Page print out..............................................................
Color test page 1 print out ..........................................................................
Color test page 2 print out ..........................................................................
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101

2-7
2. Printer Settings
2-3 List of settings
Item No.
1
2
3
4
5
6
7
8
9
10
Item
Printer Status Page print out
Prints out a list of such items as printer
default settings and memory volume, etc.
Quick Copy Job print out
Use this menu to print out Quick Copy jobs
or Proof and Hold jobs.For more information,
refer to “4-2 Quick Copy”on page 4-2.
Private Print / Stored Job print out
Use this menu to print out Private Print jobs
or Stored Job jobs. For more information,
refer to “4-4 Private Print / Stored Job
Printing”on page 4-5.
Virtual Mailbox data print out
Prints out the document data that is stored
in the Virtual Mailboxes. For more
information, refer to “4-5 Virtual Mailbox
(VMB)”on page 4-8.
Virtual Mailbox List print out
Prints out a list of the Virtual Mailboxes.
Code Job List print out
Prints out a list of the documents stored as
permanent code jobs.
Maximum number of jobs stored for
Quick Copy
Sets the maximum number of documents
that can be stored for Quick Copy.
Temporary code job partition
Sets the maximum size of the Hard Disk
partition that can be used for temporary
code jobs.
Permanent code job partition
Sets the maximum size of the Hard Disk
partition that can be used for permanent
code jobs.
Virtual Mailbox partition
Sets the maximum size of the Hard Disk
partition that can be used for virtual
mailboxes.
Display message
Print Status Page
Quick Copy
Private/Stored
Print Virtual MailBox
Data
(PRINT VMB DATA)
Virtual MailBox List
(LIST OF VMB)
Job Code List
(LIST OF CODE
JOB)
Quick Copy
Temp Code JOB
Size
(TEMPORARY
CODE JOB SIZE)
Perm Code JOB
Size
(PERMANENT
CODE JOB SIZE)
VMB Size
Remarks
Displayed only when the optional
Hard Disk is installed.
Displayed only when the optional
Hard Disk is installed.
Displayed only when the optional
Hard Disk is installed.
Displayed only when the optional
Hard Disk is installed.
Displayed only when the optional
Hard Disk is installed.
Displayed only when the optional
Hard Disk is installed.
When the actual free space on the
Hard Disk is smaller than the
amount of free space specified,
only the amount of free space
actually on the Hard Disk can be
used.
When the actual free space on the
Hard Disk is smaller than the
amount of free space specified,
only the amount of free space
actually on the Hard Disk can be
used.
When the actual free space on the
Hard Disk is smaller than the
amount of free space specified,
only the amount of free space
actually on the Hard Disk can be
used.
Available settings
No, Print
---
---
---
No, Print
No, Print
0 - 50
0 - 9999 MB
0 - 9999 MB
0 - 9999 MB

2-8
2. Printer Settings
Item No.
11
12
13
14
15
16
17
18
Item
Interface selection
Displays the interface that is currently
selected. The arrow (>) will indicate the
currently selected interface. The printer will
automatically switch to the appropriate
interface for printing.
Parallel TX/RX mode
Sets the transmission and reception mode
when the printer is connected to your
computer with a parallel interface.
Baud rate
Sets the baud rate for the serial interface.
Data bits
Sets the data bits for the serial interface.
Stop bit
Sets the stop bit for the serial interface.
Parity
Sets the parity for the serial interface.
Protocol
Sets the protocol for the serial interface.
Barcode mode
Set to “ON”when the optional Barcode
Reader is installed.
Display message
Interface
Parallel
Baud Rate
Data Bits
Stop Bits
Parity
Protocol
Barcode Mode
Available settings
Parallel, Serial,
Option 1
Auto, Normal,
High Speed,
Nibble (high)
1200, 2400, 4800,
9600, 19200, 38400,
57600, 115200
7, 8
1, 2
None, Odd, Even,
Ignore
DTR(positive)&XON/
XOFF,
DTR(positive),
DTR(negative),
XON/XOFF, ETX/
ACK
On, Off
Remarks
“Option 1”is displayed only when
the Network Card is installed.
Displayed only when the optional
Barcode Reader is installed.

2-9
2. Printer Settings
Item No.
19
20
21
22
23
24
25
26
27
Item
NetWare ON/OFF
NetWare frame type
Sets the NetWare frame type.
TCP/IP ON/OFF
DHCP ON/OFF
IP address
Subnet Mask
Gateway address
EtherTalk ON/OFF
Network Card Status Page print out ON/
OFF
Sets whether a Status Page regarding
conditions in the Network Card will be
printed out as well when the standard Status
Page for the printer (item No.: 1) or that for
use by your service representative (item No.:
99) are printed out. A more detailed Status
Page is printed out together with the
“Service Rep Status Page print out”setting
(item No.: 99).
Display message
NetWare
NetWare Frame
TCP/IP
DHCP
IP Address
Subnet Mask
Gateway
EtherTalk
Opt. StatusPage
Available settings
On, Off
Auto, 802.3,
Ethernet II, 802.2,
802.3 SNAP
On, Off
On, Off
Enter the address.
Enter the address.
Enter the address.
On, Off
On, Off
Remarks
Displayed only when the NetWare
setting is turned “On”.
Refer to “2-4 Network (TCP/IP)
settings”on page 2-19 for the
procedure on setting the network
addresses.

2-10
2. Printer Settings
Item No.
28
29
30
31
32
33
34
35
Item
Emulation protocol
Sets the emulation protocol that will be used.
Code set selection
When PCL-5c is selected as the emulation
protocol, you can select the code set that
you want to be used.
Pen (1 - 8) settings
When KC-GL is selected, you can set the
parameters of pens (1) - (8). The thickness
and the color of the pens are selectable.
Pen thickness
Sets the thickness of the pen that was
selected under the “Pen (1 - 8)”setting (Item
No.: 30).
Pen color
Sets the color of the pen that was selected
under the “Pen (1 - 8)”setting (Item No.: 30).
Page set
Specifies the original size for the data. The
printer will automatically enlarge/reduce the
data based on the original size that is
specified here and the copy paper size. If
“SPSZ”is selected, the original size that was
designated in the application will be used.
KPDL Error Report print out ON/OFF
Sets whether an Error Report will be
automatically printed out whenever a KPDL
error occurs.
Auto emulation switching
Sets the back-up emulation that, depending
upon the type of data received, may be
switched to for printing out when
“KPDL(AUTO)”is selected under the
“Emulation protocol”setting (item No.: 28).
Display message
Emulation
PCL 5c : Code Set
KC-GL Pen Adjust
Pen Width
Pen Color
(PEN COLOUR)
KC-GL Page set
Print KPDL Errs
Alt. emulation
Available settings
PCL 5c, KC-GL,
KPDL, KPDL
(AUTO)
---
Pen (1) - (8)
1 - 99 dot (s)
Black, Red, Green,
Yellow, Blue,
Magenta, Cyan,
White
A2, A1, A0, B3, B2,
B1, B0, SPSZ
On, Off
PCL 5c, KC-GL
Remarks
Allows you to set a different
emulation protocol for each
interface. Select the desired
interface under the “Interface
selection”setting (Item No.: 11).

2-11
2. Printer Settings
Item No.
36
37
38
39
40
41
42
43
44
Item
Font selection
Selects the font that will be used for printing.
This setting is made by entering the ID of the
desired font. To select an font that is already
installed in the printer, enter “I###”(with the
corresponding font ID entered in place of the
###). To verify font IDs, print out a Font List
by carrying out the “Font List print out”
setting (item No.: 39). It is possible to select
a font other than those already installed,
such as those in the optional Memory Card.
Courier font
Allows you to select between “Regular”and
“Dark”.
Letter Gothic font
Allows you to select between “Regular”and
“Dark”.
Font List print out
Prints out a list of KPDL fonts when the
emulation protocol has been set to “KPDL”
or “KPDL(AUTO)”.
Number of copies
Printing orientation
Page Protect
If “AUTO”is selected here, the machine will
monitor the data and, if necessary, will
automatically turn Page Protect ON. If a
“Print overrun”error does happen to occur
even then, the machine will automatically
change the Page Protect setting to “ON”.
Line Feed (LF) handling
Carriage Return (CR) handling
Display message
Font ID
Courier
Letter Gothic
List of Fonts
Copies
Orientation
Page Protect
LF Action
CR Action
Available settings
---
Regular
Dark
Regular
Dark
No, Print
001 - 999
Portrait, Landscape
Auto, On
LF only,
CR and LF,
Ignore LF
CR only,
CR and LF,
Ignore CR
Remarks
To select an installed font, select
the “Internal”menu. To select a font
other than those already installed,
select the “Option”menu.
Displayed only when the “Internal”
menu is selected.
Displayed only when the “Internal”
menu is selected.
A different setting can be selected
for each interface. Select the
desired interface under the
“Interface selection”setting (Item
No.: 11).
A different setting can be selected
for each interface. Select the
desired interface under the
“Interface selection”setting (Item
No.: 11).
A different setting can be selected
for each interface. Select the
desired interface under the
“Interface selection”setting (Item
No.: 11).

2-12
2. Printer Settings
Item No.
45
46
47
48
49
50
51
52
Item
Smoothing ON/OFF
Allows you to have the jaggies that appear
around the edge of text or graphics to be
evened out through a smoothing process.
EcoPrint ON/OFF
Allows printing in a toner-saving mode. This
mode is especially suited for test pages, etc.,
where high printing quality is not required.
Tone
Selects between “Normal”and “Fine”.
Gloss mode
When “High”is selected, enables print out
with a glossy finish.
Reading data
Reads the selected data on the Hard disk.
Reading program data
Reads the selected program data on the
Hard disk.
Writing data
If “OK”is selected here, the machine will
enter a “waiting for data”state until data is
sent from the host computer. To exit this
state, select the “GO”command in the
printer mode and then press the Enter key.
Deleting data
Deletes the selected data from the Hard
disk.
Display message
KIR Mode
Ecoprint Mode
Tone
Gloss Mode
Read Data
Read Program
Write Data
Delete Data
Available settings
On, Off
On, Off
Normal, Fine
Low, High
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
OK
Select the name of
the partition which
holds the data from
among those
displayed.
Remarks
For black and white print out only.
For black and white print out only.
If “Low”is selected here, the print
speed will be higher than when
“High”is selected.
Displayed only when there is
appropriate data on the Hard Disk.
Displayed only when there is
appropriate program data on the
Hard Disk.
Only when the optional Hard Disk
is installed.
Displayed only when there is
appropriate data on the Hard Disk.

2-13
2. Printer Settings
Item No.
53
54
55
56
57
58
59
60
61
62
Item
Deleting font data
Deletes the selected font data from the Hard
disk.
Deleting program data
Deletes the selected program data from the
Hard disk.
Deleting macro data
Deletes the selected macro data from the
Hard disk.
Formatting Hard Disk
If “OK”is selected here, the machine will
start formatting the Hard Disk.
Partition List print out
RAM disk ON/OFF
RAM disk size
Sets the amount of memory that will be used
as a RAM disk. The maximum size that can
be selected is the total amount of memory
installed minus the amount used by the
system (48 MB).
Reading data
Reads the selected data on the RAM disk.
Reading program data
Reads the selected program data on the
RAM disk.
Writing data
If “OK”is selected here, the machine will
enter a “waiting for data”state until data is
sent from the host computer. To exit this
state, select the “GO”command in the
printer mode and then press the Enter key.
Display message
Delete Font
Delete Program
Delete Macro
Format
List of Partitions
RAM DISK Mode
RAM DISK Size
Read Data
Read Program
Write Data
Available settings
Select the name of
the font from among
those displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
Select the name of
the partition which
holds the macro
from among those
displayed.
No, OK
No, Print
On, Off
01 - 1024 (MBytes)
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
OK
Remarks
Displayed only when there is
appropriate font data on the Hard
Disk.
Displayed only when there is
appropriate program data on the
Hard Disk.
Displayed only when there is
appropriate macro data on the
Hard Disk.
Displayed only when formatting of
the Hard Disk is required.
Only when the optional Hard Disk
is installed.
Displayed only when “On”is
selected under the “RAM disk ON/
OFF”setting (item No.: 58).
Displayed only when there is
appropriate data in the RAM disk.
Displayed only when there is
appropriate program data in the
RAM disk.
Displayed only when “On”is
selected under the “RAM disk ON/
OFF”setting (item No.: 58).

2-14
2. Printer Settings
Item No.
63
64
65
66
67
68
69
70
71
72
73
Item
Deleting data
Deletes the selected data from the RAM
disk.
Deleting font data
Deletes the selected font data from the RAM
disk.
Deleting program data
Deletes the selected program data from the
RAM disk.
Deleting macro data
Deletes the selected macro data from the
RAM disk.
Partition List print out
Reading fonts
If “OK”is selected here, the font data in the
Memory Card will be read all at once.
Reading macro data
If “OK”is selected here, the macro data in
the Memory Card will be read all at once.
Reading data
Reads the selected data in the Memory
Card.
Reading program data
Reads the selected program data in the
Memory Card.
Writing data
If “OK”is selected here, the machine will
enter a “waiting for data”state until data is
sent from the host computer. To exit this
state, select the “GO”command in the
printer mode and then press the Enter key.
Deleting data
Deletes the selected data from the Memory
Card.
Display message
Delete Data
Delete Font
Delete Program
Delete Macro
List of Partitions
Read Fonts
Read Macro
Read Data
Read Program
Write Data
Delete Data
Available settings
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the font from among
those displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
Select the name of
the partition which
holds the macro
from among those
displayed.
No, Print
OK
OK
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
OK
Select the name of
the partition which
holds the data from
among those
displayed.
Remarks
Displayed only when there is
appropriate data in the RAM disk.
Displayed only when there is
appropriate font data in the RAM
disk.
Displayed only when there is
appropriate program data in the
RAM disk.
Displayed only when there is
appropriate macro data in the RAM
disk.
Displayed only when “On”is
selected under the “RAM disk ON/
OFF”setting (item No.: 58).
Displayed only when there is
appropriate font data in the
Memory Card.
Displayed only when there is
appropriate macro data in the
Memory Card.
Displayed only when there is
appropriate data in the Memory
Card.
Displayed only when there is
appropriate program data in the
Memory Card.
Displayed only when the Memory
Card is installed.
Displayed only when there is
appropriate data in the Memory
Card.