Ojmar LOCKR COMBI User manual

LOCKR COMBI
LOCK 8001
QUICK GUIDE
V.03

WHAT TO DO IF A CODE IS FORGOTTEN
OR LOST.
The 8001 code combination lock can be opened with the
override Master key at anytime if the previously entered code
is forgotten, lost or in an emergency.
Using the Master Key to open the lock it will then also be able
to discover the code used previously.
Note: It is important and advisable that the Master Key is kept
securely and issued and controlled by management only.
1. OPEN DOOR WITH MASTER
KEY.
To open the door using the Master Key, insert into lock cylinder and turn
90º right for right hand doors and 90º left for left hand doors. The door will
now open.
With the door now open, turn the Master key 90º to the locked position
and remove.
2. CODE RECOVERY.
With the door now open and access to the rear of the lock the
combination code stored in the lock can be recovered as follows:
Firmly press and hold the code recovery lever on the inside of the lock.
See diagram bellow:
Whilst maintaining pressure on the lever, turn each code wheel from left to
right until it stops or a click is heard.
See diagram below:
3. CONFIRMING RECOVERED
CODE.
Where the wheels stop will indicate the code stored in the lock and you
should now be able to open and close the lock freely.
If the lock does not open and close freely, repeat step 2. Code recovery.
Lock rear view
Code recovery lever
Mode set screw
Lock front view
Code wheels
Open position Knob turn
Close
position RH Close position LH

HOW TO CHANGE A CODE AND
SET LOCK MODE.
HOW TO SET DEDICATED MODE
OPERATION.
The lock has two operating modes:
In this mode the same code must be used when opening the lock.
2. Free mode (R):
When set in this mode the lock code can be reset by the user of the locker.
On vacating the locker a new user can set a new code once again.
Note: The lock is supplied from the factory with the code 0-0-0-0 and set in
Free mode.
1. Dedicated mode (F):
When set in this mode the code is xed and the same code will be used to
open the lock each time.
1.
With the lock in the closed position ensure that the mode set screw on the
rear of the lock is turned to position R, see diagram below.
2.
Using the knob turn put the lock into the open position, with the blue arrow
vertical, see diagram below.
3.
Now set required private 4 digit code by turning code wheels. Remember
the code!
4.
Next turn the knob 90º left or right to the locked position according to the
hand of your lock. See diagram below:
5.
Now turn the mode set screw on the rear of the lock to position F.
The lock is now ready to be used in dedicated mode with the same code
being used every time to open the lock.
See diagram below:
Open Position
(Blue Indicator)
Closed Position
(Blue Indicator)
Right Hand Lock Left Hand Lock
Fixed Position

HOW TO SET FREE MODE OPERATION.
In this mode the code can be changed by each repeat user of the
locker.
1.
With the lock in the closed position ensure that the mode set screw on the
rear of the lock is turned to position R. See diagram below:
2.
With the knob turn the lock to the open position. See diagram below:
3.
With the lock still in the open position turn the wheels to the required 4
digit code. Remember the code!
4.
Close the door and turn the lock to the closed position according to the
hand of you lock. See diagram below:
IMPORTANT
- After step 4 for both Free and Dedicated mode, user must “scramble”
code by randomly turning code wheels. This will secure the lock and
prevent others opening the door.
Reset Position
Open Position
(Blue Indicator)
Closed Position
(Blue Indicator)
Right Hand Lock Left Hand Lock

INTELLIGENT LOCKING SYSTEMS
®
CONTACT
[e-mail]
+34.943.748.484
OJMAR HQ
Polígono Industrial de Lerun
20870 Elgoibar - SPAIN
OJMAR USA
17155 Von Karman Ave, S111
Irvine CA. 92614 - USA
www.ojmar.com