Optex Fit Series User manual

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS

EN-1

FTN-ST Standard model with 2 PIRs

FTN-AM FTN-ST with anti-masking

No.59-2263-1

INSTALLATION INSTRUCTIONS

Compact outdoor

detector

Compact outdoor

detector

fit series

• Compact design

• 190° adjustable bracket

• Intelligent AND logic

• Digital anti-masking (AM model)

• Wall tamper (option)

CONTENTS

The check mark indicates recommendation. The nix sign indicates prohibition.

Warning

Caution

Failure to follow the instructions provided with this indication and improper handling may cause

death or serious injury.

Failure to follow the instructions provided with this indication and improper handling may cause

injury and/or property damage.

Warning Caution Caution

Do not remove the PCB.

2 3 4

0.8 to 1.2 m

(2.6 to 3.9 ft.)

Parallel

Mounting height.

Tilt

Keep the detector parallel to the ground. Consider the direction of the intruder,

for the setting of the detection area.

Do not touch the PCB except for the

DIP switch.

1 INTRODUCTION

1-1 BEFORE INSTALLATION ...................................... 1

1-2 PARTS IDENTIFICATION...................................... 2

1-3 DETECTION AREA................................................ 2

2 INSTALLATION

2-1 INSTALLATION...................................................... 3

3 WALK TEST

3-1 WALK TEST ........................................................... 5

4 DIP SWITCH SETTING

4-1 LED ........................................................................ 5

4-2 ALARM OUTPUT ................................................... 5

4-3 PIR SENSITIVITY .................................................. 5

4-4 ANTI-MASKING...................................................... 6

5 OTHERS

5-1 WALL TAMPER (OPTION) CONNECTION ........... 6

5-2 EXAMPLE OF EOL WIRING.................................. 7

5-3 LED LIGHT PATTERN ........................................... 7

6 SPECIFICATIONS

6-1 SPECIFICATIONS.................................................. 8

6-2 DIMENSIONS......................................................... 8

WIRED MODEL

1INTRODUCTION

1-1

BEFORE INSTALLATION

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS

EN-2

2345

(m)

(ft.)

(m)

-Optional accessories

Wall tamper (WRS-02)

Bracket

Sponge Fixture

Main unit

Main unit cover

Lens

Screw kit

Screw (3 × 20 mm)

0 5 10 15

0.8

(m)

1.0

1.2

2.6

(ft.)

3.3

3.9

10 2 3 4 5

(m)

(ft.)

0 5 10 15

0.8

(m)

1.0

1.2 10 2 3 4 5

(m)

2.6

(ft.)

3.3

3.9

(ft.)

Top view Side view

2 m detection length

5 m detection length

Adjustable range: 95°

(by 5° pitch)

Adjustable range: 95°

(by 5° pitch)

Sponge

Install the detector in a place where it is free from false alarm factors. For example:

• Objects moving in the wind

• Heat source

• Sunlight and reflection

1-2

PARTS IDENTIFICATION

1-3

DETECTION AREA

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS

EN-3

2345

(m)

(ft.)

(m)

-Optional accessories

Wall tamper (WRS-02)

Bracket

Sponge Fixture

Main unit

Main unit cover

Lens

Screw kit

Screw (3 × 20 mm)

0 5 10 15

0.8

(m)

1.0

1.2

2.6

(ft.)

3.3

3.9

10 2 3 4 5

(m)

(ft.)

0 5 10 15

0.8

(m)

1.0

1.2 10 2 3 4 5

(m)

2.6

(ft.)

3.3

3.9

(ft.)

Top view Side view

2 m detection length

5 m detection length

Adjustable range: 95°

(by 5° pitch)

Adjustable range: 95°

(by 5° pitch)

Sponge

Install the detector in a place where it is free from false alarm factors. For example:

• Objects moving in the wind

• Heat source

• Sunlight and reflection

1-2

PARTS IDENTIFICATION

1-3

DETECTION AREA

Open the main unit cover.

Remove the fixture.

Hold the top of the bracket

lifted and remove the main unit.

Note>>

• For wall tamper wiring (option), refer to 5-1.

Bracket

Main unit

Put the wire extending from the wall through the

wiring hole in the bottom of the bracket, and

mount the bracket on the wall.

Pull the wire through the main unit.

Lift the top of the bracket slightly and mount the main

unit to the bracket.

83.5 mm

(3.29 inches)

Screw (3 × 20 mm)

Mounting height:

0.8 to 1.2 m

(2.6 to 3.9 ft.)

Screw (3 × 20 mm)

Sponge

Fixture

Wire terminal connections.

Notes>>

-Power cable length

The power cable should be limited to the following length.

FTN-ST FTN-AM

12 V 14 V 12 V 14 V

Power input (+)

Power input (-)

Alarm output

COM

Spare

Tamper

FTN-ST

(-)

Alarm output

COM

Trouble output

Tamper

FTN-AM

Power input (+)

Power input

• Anti-masking output is recognized as

TROUBLE.

• For EOL, refer to 5-2.

Unit: m (ft.)

Cable diameter

AWG22 (0.33 mm2)

AWG20 (0.52 mm2)

AWG18 (0.83 mm2)

340 (1120)

530 (1740)

850 (2790)

730 (2400)

1160 (3810)

1850 (6070)

290 (950)

450 (1480)

720 (2360)

620 (2030)

980 (3220)

1570 (5150)

2INSTALLATION

2-1

INSTALLATION

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS

EN-4

8Determine the detection length. (2 m or 5 m)

Side view

0 5 10 15

2.6

0(ft.)

3.3

3.9

0.8

(m)

1.0

1.2

(ft.)

10 2 3 4 5

(m)

0 5 10 15

0.8

(m)

1.0

1.2

2.6

0(ft.)

3.3

3.9

10 2 3 4 5

(m)

(ft.)

Side view

5 m detection length (Factory default)

2 m detection length

If 2 m is required, rotate the lower

lens 180 degrees.

9Attach the main unit cover. 10 Perform walk test.

Note>>

• To prepare for walk test, check that DIP switch

1 (WALK TEST MODE) is set to “ON (TEST)”

before attaching main unit cover.

7Determine the horizontal detection angle

and attach the fixture.

• When the unit is mounted on the

wall to look transversely,

choose the guide-mark

engraved.

• When the unit is mounted on the

corner to look ahead along the wall,

choose the guide-mark

located on the opposite

side of the wall.

Note>>

• Check that the fixture and

bracket engage correctly.

Note>>

Align the detection area

parallel to the wall to

reduce interference with

the wall.

Note>>

• To make adjustments, remove the fixture.

Note>>

• Do not remove the upper lens.

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS

EN-5

Set DIP switch 1 (LED) to “ON”.

1234

Note>>

• The switch is set to “ON” by factory default.

DIP switch

Check that LED lights for 2 seconds

when the intended object is detected.

1234

If the LED does not need to be turned on at all times,

set the DIP switch 1 (LED) to “OFF”.

DIP switch

N.O.

N.C.

STD

LOW

1234

Do not touch the PCB except

for the DIP switch and the

terminal.

●: Factory default

DIP switch

1 LED

2 ALARM OUTPUT

3 PIR SENSITIVITY

4 ANTI-MASKING

(Factory default)

LED OFF

LED ON

FunctionPosition

OFF

N.O.

N.C. output

N.O. output

FunctionPosition

N.C.

(Factory default)

STD

(Factory default)

Low sensitivity

Normal sensitivity

FunctionPosition

LOW

OFF

1234

3WALK TEST

4DIP SWITCH SETTING

3-1

WALK TEST

4-1

LED DIP switch 1 FTN-ST

FTN-AM

4-2

ALARM OUTPUT DIP switch 2 FTN-ST

FTN-AM

4-3

PIR SENSITIVITY DIP switch 3 FTN-ST

FTN-AM

Detected Not detected

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS

EN-6

Note>>

-ANTI-MASKING function

ANTI-MASKING test mode

The trouble is output after 20 seconds.

Normal mode

The trouble is output after 3 minutes.

10 minutes1 minute

Teaching

When masking condition continues more than 3 minutes, TROUBLE will be generated.

TROUBLE is generated after 20 seconds under the anti-masking test mode.

Please close the main unit cover before turning on the power supply.

“Teaching mode” will begin immediately after the power is supplied.

Re-starting the power is necessary if the power has been applied prior to the closing.

Please be careful not to leave any object within 1 m from the unit.

• If a trouble is output (mal-detection of anti-masking) immediately after the operation has

started, set the DIP switch 4 (ANTI-MASKING) to “OFF” and then to “ON”, and close the cover.

OFF

Connect the tamper lead as shown below when connecting a wall tamper (option).

CAL

+SP TP TP

Twist and swage

the wires.

Control panel

-Mounting position

Note>>

• Pull the wire through the bracket before

installing the wall tamper (option).

Bracket

Sponge

(Factory default)

ANTI-MASKING OFF

ANTI-MASKING ON

FunctionPosition

OFF

4-4

ANTI-MASKING DIP switch 4 FTN-ST

FTN-AM

5OTHERS

5-1

WALL TAMPER (OPTION) CONNECTION

1234

Wall tamper (option)

WRS-02

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS

EN-7