Optex AP-360BR User manual

AP-360BR(C)
Indoor Recessed Mount PIR Detector
360°/Battery operated model
INSTALLATION INSTRUCTIONS
No.59-3222-0 2207-04
1
- Manufacturer’ s statement
- Parts identification
- Specifications
- Dimensions
- Detection area
- Troubleshooting
- Timing chart
- Compliance
Before installation
Others
<< Contents >>
Page
2
3
Installation
Ceiling mount
without switch box
Wiring
2
Ceiling mount
with 86-type box
Checking3
56
4
7
9
10
11
11
8
10
Settings1
12
Indoor Recessed Mount PIR Detector
AP-360BR(C)
360° ø6.0 m (20’ ) detection area at 4.5 m (14’ 9” ) mounting height
EN

- Manufacturer’ s statement
NOTE
Failure to follow the instructions provided with this indication
and improper handling may cause death or serious injury.
Failure to follow the instructions provided with this indication
and improper handling may cause injury and/or property damage.
Check mark indicates recommendation.
Nix sign indicates prohibition.
Special attention is required to the
section of this symbol.
Mounting height
2.5 to 4.5 m (8’2” to 14’9”)
Symbol Meaning
Warning
Caution
Warning
Caution
Wetting with water
2
Symbol Meaning
Before installation
Destroy
modify Outdoor installation
Detection through glass
Follow to the Regulations
Partial/complete obscuration
of the detection area.

- Parts identifications
3
Top cover
Lens
Base cover
JP2
PIR sensitivity
JP1
Alarm output mode
SW1
Tamper switch
Accessories
Retaining spring x 2
Fixing screw
Mounting Bezel
for an 86-type box
Screw cap x 2
JP3
Battery saving timer

Disassemble
Settings
1
4
Open the base cover, and to set the detector.
N.C. (default) N.O.
Turn the jumper PIN
by 90 degrees to prevent
interference with the casing.
Jumper pin settings
Assemble
Close the base cover, and fasten the screw to fix the cover.
JP1
Alarm output mode
JP2
PIR sensitivity
1
2
3
120 s (default) 5 s
JP3
Battery saving timer
H (recommended) M (default) L
Mounting height: > 3.5 m 3.0 to 3.5 m < 3.0 m
(11’6”) (9’10” to 11’6”) (9’10”)

2-1. Ceiling mount without switch box
5
Installation
2
Install a retaining spring on both sides.
(follow the illustrated arrow steps to complete the assembly of the retaining spring.)
1
2
3
Mount the detector on the ceiling.
(Be sure to arrange the wires with a downward slope to prevent water igress into the detector.)
1
4
2 3 Insert the detector into the hole with the retaining spring facing up.Make a ø45 mm (1.77”) hole in the ceiling for mounting.
ø45 mm
(1.77”)
Accessories
used in this installation
Retaining spring x 2
Transmitter

6
2-2. Ceiling mount with 86-type box
Alarm
Tamper
Transmitter
For the 86-type box mount, dual 86-type boxes are recommended
with the additional one used to accommodate the transmitter.
NOTE
Accessories
used in this installation
Mounting Bezel
for an 86-type box
Screw cap x 2
Options
to procure in the market
86-type box x 1 or 2
Screw x 2
1
Prepare an 86-type box on the ceiling.
Install the detector into the 86-type box.
2
Align the bump with the triangle recess as illustrated in the figure.
NOTE
Fix the detector with two screws and cover their heads with two caps.
3
Transmitter

7
2-3. Wiring
[1] Red
[2] Black
[3] White
[4] Yellow
[5] Green
[6] Blue
Power supply: positice
Power supply: negative
Alarm output
Alarm output
Tamper output
Tamper output


Alarm
Tamper
Transmitter

8
Power on. Wait for 60 seconds to complete the warm-up time.
Walk in the detection area to check the detecting performance.
3-1. Walk test
3Checking
12
3Start operation.
4
Power
60 sec.

9
• Specifications and designs are subject to change without prior notice.
• These units are designed to detect an intruder and activate an alarm control panel.
Being only a part of a complete system, we cannot accept responsibility for any
damages or other consequences resulting from an intrusion.
- Specifications
Others
Detection method
Detection area
Mounting height
Mounting mode
Sensitivity
Detection speed
LED indicator
Alarm cycle
Battery saving timer
Alarm output
Tamper switch
Warm-up time
Power supply
Current
PIR sensitivity
Weight
Operation temprature
Operation humidity
Location
Dimensions
Passive infrared
N.C. 28 V DC 100 mA max.
The contact opens once the casing is detached.
Approx. 60 s
H/ M/ L
< 95%
Indoors

Model AP-360BR(C)
Warm-up upon power on: blinking
Stand-by: off
Walk test: solid on
Alarm: off
Approx. 2 s
120 s/ 5 s selectable
N.O./N.C., 3.6 V DC 10 mA max.
2.7 to 3.6 V DC (CR123A battery)
3 V DC
Stand-by: 10цA, Max.: 4 mA
ø6 m (ø20’ at mounting height: 4.5 m (14’9” ft.)
2.5 to 4.5 m (8’2” ft. to 14’9” ft.)
2.0℃at 0.6 m/s (3.6°F at 2’/s)
0.3 to 3.0 m/s (1‘/s to 9’10”/s)
50 g (1.76 oz)
-20 to +50℃(-4°F to +122°F)
86 x 86 x 42.5 mm (3.39 x 3.39 x 1.67 in.): with 86-type box mount
ø52 x 42.5 mm (ø2.05 in. x 1.67 in.): without switch box mount
Recessed ceiling mount/86-type box mount

10
- Dimensions
- Detection area
0
2.0 (6’7”)
2.5 (8’2”)
3.0 (9’10”)
3.5 (11’6”)
4.0 (13’1”)
4.5 (14’9”)
Side view
Top view
3 2 1 0 1 2 3
(9’10” 6’7” 3’3” 0 3’3” 6’7” 9’10”)
3.0 (9’10”)
2.0 (6’7”)
1.0 (3’3”)
0
1.0 (3’3”)
2.0 (6’7”)
3.0 (9’10”)
Mounting height
Detection area
Maximum detection area
2.5
(8’ 2’ )
ø3.3
(ø10’ 10” )
3.0
(9’ 10” )
ø4.0
(ø13’ 1” )
3.5
(11’ 6” )
ø4.6
(ø15’ 1” )
4.0
(13’ 1” )
ø5.4
(ø17’ 8” )
4.5
(14’ 9” )
ø6.0
(ø20’ )
Unit: m (ft., in.)
3 2 1 0 1 2 3
(9’10” 6’7” 3’3” 0 3’3” 6’7” 9’10”)
Without switch box mount
  
With 86-type box mount
Unit: mm (inch)
86 (3.39)
86 (3.39) 42.5 (1.67)
ø52 (2.05) 42.5 (1.67)
102 (4.02)