Optex VX-402 User manual

VX-402, VX-402REC
MULTI STABILIZED OUTDOOR DETECTOR
Standard model Voice Warning model
No.59-1004- 4 0707-11
2YEAR WARRANTY
FEATURES
CONTENTS
Voice Warning Function
(VX-402REC Only)
Easy Recording with Built-in
microphone or External apparatus
(VX-402REC Only)
Limited Detection Range Function
Size Judging Function
Bright Light Disturbance Immunity
Detection Area Extension Function
Directional Detection Function
VX-402REC is capable of delivering two kinds of audible messages
to an intruder. This has been proven as an effective means of
deterring BREAK-INS.
The VX-402REC detector records warning messages by either of
two different ways: speak direct to its built-in microphone or connect
an external sound source to the detector.
The detection range of the VX-402 can be limited to avoid detecting
unwanted objects. By limiting the detection range, false alarms due
to unwanted movement ( i.e. cars, persons or animals outside the
protected area ) can be reduced.
VX-402 is designed to discriminate between large and small
animals. By utilizing this ability, false alarms due to small animals
can be reduced.
VX-402 is equipped with Double Conductive Shielding (Patent
Listed). This shielding greatly reduces the chance of false alarms
due to car headlights, sunlight and other ambient light sources.
The detection area can be easily extended by using its slave units.
VX-402 can distinguish movement direction by using slave units.
This function increases the operational reliability and allows for use
in new applications (Directional Security).
1.INSTALLATION HINTS
2.DESCRIPTION AND OPERATION
3.INSTALLATION
4.WIRING
5.RECORDING
6.SETTING & ADJUSTMENTS
7.FUNCTIONS
8.OPERATION TEST
9.TROUBLE SHOOTING
10.SPECIFICATIONS
11.DIMENSIONS
2
3
4
5
6
7
10
13
14
16
16
-1-
alarm shop

Safety-Related Precautions
•Before installation, make sure to read this instruction manual carefully for safe and effective product
operation.
•After reading this installation manual, make sure to keep it in a convenient place for future use.
If the sensor is installed with some angle to the ground,
operational reliability of the sensor may be decreased.
1.INSTALLATION HINTS
5.Avoid pointing the sensor towards moving objects
(i.e. swaying trees, bushes, flags,etc.). If moving
objects are unavoidable, please refer to
Trouble Shooting reference for proper installation.
3.Mount the sensor so that a majority of traffic flow is
across the detection pattern.
4.VX-402 is designed to protect any light disturbances.
However, too much light may cause unstable
condition with the sensor, such as; strong sunlight
directed or reflected exactly into the sensor's field
of view. It is recommended to avoid such installation.
2.Installation height is 0.8m-1.2m (2.7ft-4ft)
This icon denotes a situation involving the risk of serious
injury or damage to property if the warning given is ignored.
Caution
This icon denotes a situation involving the risk of serious
injury or even death, if the warning given is ignored.
Warning
This icon indicates actions to be avoided. Details of the actions to be
avoided are written beside or near icon.
This icon indicates instructions that should be strictly followed.
Never use this product for any application except purpose for detecting
moving target such as a human or a car. In addition, never use for any
activation for a shutter or other. It may cause hazards.
Clean and inspect the device periodically for safe operation.
If any defect is detected, ask your local supplier to repair the device.
To avoid the risk of electric shock, never touch the main body of the product
with wet hands. (Also, if the product is wet after rain do not touch it.)
Never attempt to connect the terminals to units which reguire higher
power supply or current draw than its rating. It increases the risk of fire or
damage to the product.
Never attempt to disassemble or modify the product, which
increases the risk of fire or damage of the product.
Avoid applying water in directly from brackets, houses, or otherwise
splashing water directly onto the product. It increases the risk of damaging
the product.
Warning
Warning
Warning
Warning
Caution
Caution
-2-
1.Install the sensor perpendicular to the ground to
making upper detection area parallel to the ground.
Parallel
0.8m-1.2m
(2.7ft-4ft)
alarm shop

2.DESCRIPTION AND OPERATION
-3-
Pole Mount Bracket M4 x 12
Plate
M4 x 6
Mounting Screw
T4 x 20
Terminals
Pyro Electric Sensor
(Do not touch)
Speaker (VX-402REC only)
Plate Lock Screw
Lock Screw
Cover
LED Indicator
DIP Switch A
(Page 9) Lens Holder
Lens
Cover
Area Masking Plate
(Page 8)
DIP Switch B
(Page 9)
Detection Length
Adjustment Switch
(Page 9)
Sensitivity Select
Switch (Page 9)
There are switches only for
VX-402REC in this portion (Page 6, 9)
alarm shop

3.INSTALLATION
Loosen the lock screw and
remove the cover.
3-1.Before the Installation
Loosen the plate lock screw
[about 10mm (0.4")].
3-2.Wall Mount
(a)Upper Knockout Wiring Hole (b)Lower Knockout Wiring Hole
Remove the lower
knockout of the
unite cover, lead
the wire through
the knockout hole.
Remove the upper
wire knockout.
Pull the wire through wiring hole and
install the plate on the wall by using
provided mounting screws (two places). Fasten the plate lock screw and
connect the wires to the terminal.
Lead the wire to the groove
on the unit base, through the
wiring hole at the terminals.
Apply an adhesive sponge pad
over the wiring hole. Hook the
unit base onto the plate.
Adjust the DIP switch, detection
area and sensitivity. Secure the
cover with the lock screw.
Remove the plate by sliding it down
and away from the unit base.
Lead the wire through
the upper side of the
unit base, lead the wire
to the wiring slit then
through the wiring hole.
-4-
IMPORTANT
• Install the unit perpendicular.
• Installation height must be between
0.8m and 1.2m (2.7 ft and 4 ft).
• Secure a space 110mm (4.4") or
more to the upper part of plate for
opening and closing of the cover.
Surface wiring
Wiring Groove
Wiring Hole
( Terminals) Wiring Sponge Pad
Plate Lock
Screw
Wiring Hole
Mounting Screw
T4 x 20
alarm shop

Peel off one of the two
sealings along the
dotted line.
Fix bracket onto mounting plate with
supplied screws (M4x6,4pcs).
Place the bracket around the pole
and tighten firmly with pole locking
screws.
3-3.Pole Mount
An installation pole with an outside diameter of 43mm(1.66") must be used.
(Standard U.S.11/4"pipe has an outside diameter of 1.66".)
For outdoor wiring, bury piping as
deep as possible. Some sites will
require metal coated cables for
underground wiring work.
Avoid aerial wiring
Wiring Sponge Pad
3-4.Electric Box Mount
For connections to single gang
electric boxes, follow instructions
for wall mounting.
Pitch 83.5mm (3.28")
3-5.Conduit Installation
Conduit can be installed directly into the bottom of the unit by
removing the knockout on the bottom on the cover.
Knockout
4.WIRING
VX-402REC
AUX INPUT:[NC]
VX-402
AUX INPUT:[NC]
Power wires should not exceed the following lengths.
VOICE CONTROL INPUT
POWER INPUT:9.5 - 18VDC
ALARM OUTPUT:[NC/NO] SELECTABLE
SPARE SPARE
TAMPER:[NC]
ALARM OUTPUT:[NC/NO] SELECTABLE
VOICE OUTPUT
POWER INPUT:9.5 - 18VDC
TAMPER:[NC]
JUMPER JUMPER
-5-
Approx.
1m(33ft)
Approx.
10cm
(3.3")
Approx.
60cm(20")
IMPORTANT
• Do not remove jumper while
slave is not connected. Otherwise,
VX-402 series continue to give the alarm.
• Use AUX INPUT terminal only
when slave is used.
12V 14V 12V 14V
AWG 22(0.33máu) 200m(670ft) 400m(1330ft) 110m(370ft) 230m(770ft)
AWG 20(0.52máu) 340m(1130ft) 640m(2130ft) 180m(600ft) 360m(1200ft)
AWG 18(0.83máu) 510m(1700ft) 1020m(3400ft) 290m(970ft) 570m(1900ft)
VX-402 VX-402REC
WIRE GAUGE
AWG 22(0.33mm2)
AWG 20(0.52mm2)
AWG 18(0.83mm2)
alarm shop

5.RECORDING
5-1.Description for Recording
5-2.Recording Method
-6-
The VX-402REC detector records warning messages by either of two different ways: speak direct to its
built-in microphone or connect an external sound source (tape-recorder or computer etc.) to the detector.
1
2
4
5
Set the detectorís recording
level volume for max. Connect the earphone, headphone jack or line out jack of the external sound source
with the detector's jack using connection
cable with monaural plugs.Set the
detector’s recording level volume for min.
Choose track A or track B on which to record.
* To record on track A (track B), set DIP switch B-3 (4) for active.(See page 9.)
Speak a message to the
microphone.
*Speak loud enough to blink the
recording level indicator.
Play back a desired message/sound on the
sound source and adjust the detector’s
recording level volume so that the recording
level indicator may blink.
When recording is completed, the detector automatically plays back the recorded
message/sound. Listen to check if the sound volume and quality are satisfactory.
If not, go back to step 3 above and repeat the procedure thereafter.
Recording Level Indicator
Recording Level Volume
Recording Start Switch
External Input Jack
Microphone
Voice Mode Switch
VoiceVolume
Day/Night Message:
Armed/Disarmed:
Sequential Message:
Pre-Warning:
MIN. MAX.
Microphone Sound Source
IMPORTANT
•Do not record big volume from the beginning, which could overload and damage the speaker.
•Do not record the sound of chimes or a siren, which could overload and damage the speaker.
•For connection with sound source, use the plug which suited for the jack form of the apparatus.
•A blinking recording level indicator shows that an adequate sound volume has been ensured.
If reproduced sound is heard broken, adjust the sound level with the detectorís recording level
volume or the sound source’s volume controller.
3Press the recording start switch.
* The detector can record while its LED indicator blinks approx 8 seconds.
123
4
alarm shop

6-1.Detection Length Adjustment
Length of Lower Detecion Area decides
detection length
The upper detection area stays parallel to the
ground at all time. The lower detection area
moves as shown above depending on the switch
position. So, length of the detection is limited by
the length of lower detection area, since both
upper & lower detection area have to be blocked
at the same time to activate the sensor.
6.SETTING & ADJUSTMENTS
Press and slide the Detection Length Adjustment Switch to the desired position.
Detection Length
Adjustment Switch
D
C
B
A
Detection Length setting chart
Instration Height=1m(3.3ft)
*The maximum detection length may vary as
above due to environmental thermal conditions.
IMPORTANT
If there is a traffic near the dettection area, please
adjustdetectiion 1.5m to 2.0m(5ft to7ft) away from
movements.
(See section 8 OPERATION TEST on page 13
for the details.)
Side view of detection pattern
D
A
Adjustable zone. POSITIONB
0 5 10 12 m
0 10 20 30 40 (ft)
POSITION C
POSITION D
POSITIONA
0 5 10 12 m
0 5 10 12 m
0 10 20 30 40 (ft)
0 10 20 30 40 (ft)
0 5 10 12 m
0 10 20 30 40 (ft)
Only lower
detection area
is blocked
NO
Detection
NO
Detection
Both upper and
lower detection
area are blocked!
Detection!
Detection Length
Detection Length
Only upper
detection area
is blocked
Detection Length
IMPORTANT
BOTH DETECTION AREA MUST BE BLOCKED FOR DETECTON
-7-
1m
(3.3ft)
1m
(3.3ft)
1m
(3.3ft)
1m
(3.3ft)
Standard
12.0 10.0 - 15.0
(40.0) (33.3 - 50.0)
8.0 6.0 - 10.0
(26.7) (20.0 - 33.3)
5.0 4.0 - 5.5
(16.7) (13.3 - 18.3)
2.0 1.5 - 2.5
(6.7) (5.0 - 8.3)
m (ft)
C
D
*
MAX DETECTION LENGTH
A
B
POSITION
alarm shop

6-2.Area Angle Adjustment
6-3.Area Masking
Hold the pyro electric unit
and turn it to the desired
direction (15°steps).
Area angle is 90°with 7 fingers
by 15°Turn optical cylinder.
Angle moves by 15°per notch.
Active
detection
fingers.
Top view
45°Adjustable
45°Adjustable
12 10 5 0 5 10 12 m
40 30 20 10 0 10 20 30 40 (ft)
0 5 10 12 m
0 10 20 30 40 (ft)
45゜ 90゜
45゜
2. Separate the lens from
the cover.
1. Remove the lens holder from the
cover as shown above. 3. Apply the provided area masking plate to the inside of the lens
on the zone to be eliminated.
IMPORTANT
As shown at left, the active
detection fingers are always 7,
if the area masking plate is not
applied.
The active fingers are varied by
area adjustment as explained at
above.
Before putting the area masking
plate to the inside of the lens,
make sure which part of the
lens will be the detection areas
you want to eliminate. There is
no effect if you put the plate on
the part of the lens which do not
cover the detection area.
4. Put the lens back in by aligning
the 4 projections on the cover to
the 4 cut outs on the lens. Please
do not put the lens up side down.
5. Place the lens holder. Confirm
the lens holder is held by left
and right prongs on the cover.
-8-
alarm shop

:Set Directional Detection to OFF.
:Do not set a voice mode switch as Pre-Warning
When greater sensitivity is desired,
select "H". When the installation site is
poor (bad conditions) select "L".
6-4.Sensitivity Adjustment
Sensitivity Select
Switch (L,M,H)
6-5.Voice Warning Function Setup (VX-402REC only)
3. Volume adjustment
Voice
Volume
MIN.
MAX.
Adjust the voice volume by
turning the adjustment .
6-6.DIP Switch Setup
-9-
1. Choosing a playback mode
The VX-402REC detector provides several playback modes.(See section7 on page 10-12.)
Choose the desired mode using the voice mode switch.
2. Message selection and recording
Choose and record a message suitable for the function to be used.
For message selection, operate the DIP switch B. (See section 6-6.)
4. External speaker
An external speaker may be connected to the VX-402REC detector to thunder the intruder away.
DIP SWITCH A
NIGHT
ONLY DAY NIGHT
DETECTABLE DIRECTION:
ALARM OUTPUT:
DIRECTIONAL DETECTION:
DAY/NIGHT MODE:
:LED INDICATOR
:PULSE COUNT
:MESSAGE A
:MESSAGE B
:LED INDICATOR
:PULSE COUNT
SLAVE
->
VX-402
VX-402
->
SLAVE
N O N C
ONOFF
24
OFF ON
24
ACTIVE PAUSE
PAUSE
VX-402
IMPORTANT
VX-402REC
NIGHT
ONLY DAY NIGHT
DETECTABLE DIRECTION:
ALARM OUTPUT:
STATUS SELECT:
DAY/NIGHT MODE:
SLAVE
->
VX-402
VX-402
->
SLAVE
N O N C
-ARM +ARM
DIP SWITCH B
OFF
VX-402
VX-402REC
When AUX INPUT is not connected, set as follows.
SPEAKER Wiring between Power (–) andVoice Output •Recommended speaker
Impedance : 8
Max powe •r : over 30W
Output S.P.L: over 90dB/m
Weatherproof
•Speaker with amplifier can
not be used.
•Wiring length
AWG18(0.83mm2): 10 m
IMPORTANT
ON
ACTIVE
Wiring Diagram
1234
1234
12
1234
Power (–)Voice Output
alarm shop

7-1-1.Detection Area Extension Function (DIP switch A-3/Directional Detection:OFF)
When the Directional Detection mode is selected OFF:
The functions of the VX-402 series can be extended by connecting components such as outdoor
PIR's, active IR beams or magnetic contacts to the AUX INPUT terminal.
7.FUNCTIONS
From POWER SUPPLY
(9.5-18VDC)
Case A=>ALARM
Case B=>ALARM
case:A
VX-402series
When a slave is connected,
Please remove the jumper.
AUX INPUT POWER INPUT ALARM OUTPUT
(NC.)
To Control Panel
ALARM
OTUPUT
VX-402 Series
POWER
INPUT
Slave
(additional sensor)
case:B
Slave
Alarm signal will be sent to the control panel when either VX-402 series
or slave activates.
(In VX-402REC, do not set the voice mode switch as Pre-Warning.)
SLAVE -> VX-402 series :
VX-402 series -> SLAVE :
When the Directional Detection mode is selected ON:
7-1-2.Directional Detection Function (DIP switch A-3/Directional Detection:ON)
When a person passes the SLAVE area then
enters the area covered by the VX-402 series
within 1 minute, the VX-402 series will
activate.(See page 11.)
When a person passes the VX-402 series area
then enters the area covered by the SLAVE
unit within 1 minute, the VX-402 series will
activate. (See page 11.)
-10-
Alarm signal will be sent to the control panel when both VX-402
series and slave activate. In this case, select the direction by the
DIP switch A. (See section 6-6 on page 9.)
InVX-402REC, set the voice mode
switch as Pre-Warning.
7-1.Two Detectors Mode
Wiring Diagram
Voice Mode Switch
1234
alarm shop

No Voice
When it passes along the
area of VX-402REC.
Caution!
(Message A)
When it passes along the
area of VX-402REC.
SLAVE-> VX-402 series :
VX-402 series -> SLAVE :
Slave VX-402/402REC
(No Alarm)
(Alarm)
(No Alarm)
(No Alarm)
Slave VX-402/402REC
Slave VX-402/402REC
Slave VX-402/402REC
(No Alarm)
(No Alarm)
(No Alarm)
(Alarm)
-11-
VX-402REC
When it passes along the
area of slave.
When it passes along the
area of slave.
Caution!
(Message A)
Warning!
(Message B)
VX-402REC
VX-402/402REC
VX-402/402REC
When it passes along the
area of VX-402REC.
Warning!
(Message B)
When it passes along the
area of slave.
Caution!
(Message A)
Caution!
(Message A)
When it passes along the
area of VX-402REC.
When it passes along the
area of slave.
No Voice
VX-402RECVX-402/402REC
VX-402RECVX-402/402REC
IMPORTANT
•During the Direction Detection mode is set ON, the alarm occurs only when the detector which set as
second-detection detects the moving object. If the second-detection detector doesn’t detect the anything
within 60 seconds after the first alarm occurred, the alarm is reset.
•In case the VX series are used for both master and slave unit, use the slave unit with following setting mode.
VX-402 : Set the Direction Detection mode OFF.
VX-402REC : Do not set the voice mode switch as a pre-warning mode.
alarm shop

7-2.Day/Night Message Mode (VX-402REC only)
7-3.Arm/Disarm Mode (VX-402REC only)
7-4.Sequential Message Mode (VX-402REC only)
-12-
In case, the detector detects the moving object 3 times within 30 seconds during the Sequential
Message mode is set ON, the message is automatically changed from 3rd time detection.
1st and 2nd time detection (within 30 seconds) : Message A
3rd time detection (within 30 seconds) : Message B
The detector will automatically change messages from that for the daytime to that for the night-time and
vice versa.
Daytime : Message A
Night-time: Message B
The detector will sound different messages when it is set for the armed mode or disarmed mode.
Armed : Message A
Disarmed: Message B
Caution!
(Message A) Warning!
(Message B)
Caution!
(Message A) Warning!
(Message B)
ARMED
ControlPanel
DISARMED
ControlPanel
Non-Voltage Contact Control Voltage Control Non-Voltage Contact Control Voltage Control
OPEN DC 5 - 18V CLOSE DC 0 - 1V
CLOSE DC 0 - 1V OPEN DC 5 - 18V
+ARM –ARM
Armed
Disarmed
Detector Setting
Control Panel
Non-Voltage Contact Control Voltage Control
Wiring between Power(–)and Voice Contorol Input Wiring to PGM Programmable Output
Control Panel
Non-VoltageContactOutput Control Panel
PGMOutput
Caution!
(Message A) Warning!
(Message B)
Voice Mode Switch
Voice Mode Switch
Voice Mode Switch
Power(–) VoiceContorolInput VoiceContorolInput
123
4
123
4
123
4
alarm shop

VX-402 has a multi-level detection pattern (from side view). A heat source beyond the
detection area may cause the detector a false alarm by reflecting off the ground.
Examples of reflective ground is water (puddle), wet road, smooth surface concrete and
asphalt road. Reflection rate is not 100% of course on the ground, however, if the heat
source is strong and / or reflection rate is high, detectors detection distance will be
longer than required and may detect unwanted objects beyond. According to the
ground condition of the installation site, select the detection range position.
8.OPERATION TEST
1.Turn LED indicator on. (See page 9.)
2. Check and adjust the detection area. (See pages 7,8.)
1) Please adjust the detection length to position B.
The detection length will be around 8m (27ft) which
is rather shorter than ideal length but can remove
the chance of false detection.
a
b
IMPORTANT!
When the car or person goes near the detection area (a), please adjust the detection
area 1.5m to 2m (5ft to 7ft) shorter than movement area (b) and confirm by walk test.
Because, the actual detection area may change from 1.5m to 2m (5ft to 7ft) due to
the environmental thermal conditions.
When around 13m (43ft) detection area is required as shown below.
The detection area might increase when there is a
big temperature difference between the moving
object and the background.
1) If the detection length adjusted to position
A[12m (40ft)], there is a possibility to detect
the car, depending on the environmental
thermal conditions. Approx.12m(40ft)
position A
Approx.8m(27ft)
b
Approx.12m(40ft)
position B
a
Approx.8m(27ft)
position B
Approx.13m(43ft)
In such case,
Confirm by walk test. Detects at area a and no
detection at area b.
2)
1)
2)
-13-
Example
alarm shop

PROBLEM DESCRIPTION PROBABLE CAUSE REMEDY
Incorrect power supply voltage. Set supply voltage for a range of 9.5 to 18 VDC.
LED does not light. LED switch is turned OFF. Turn LED switch ON.
(See section 6-6 on page 9.)
DIP switch A-4 is set for Night Only. Set switch A-4 for Day/Night and see if it works.
(See section 6-6 on page 9.)
DIP switch A-3 (Directional Detection)
is turned ON. Turn OFF DIP switch A-3. (See section 6-6 on page 9.)
Fau
Çå
ty wiring to detector. Rewire alarm output correctly.
(See section 4 on page 5.)
LED blinks
continuously Incorrect power supply voltage. Set supply voltage for a range of 9.5 to 18 VDC.
Make alarm
continuously Jumper is not connected to the AUX INPUT terminal. Connect the jumper to the terminal. (See section 4 on page 5.)
Detector is not installed perpendicularly
to the ground. Reinstall the detector perpendicularly to the ground. (See section3-2 on page 4.)
Lower detection area is unnecessarily long. Confirm and reset the detection area.
(See section6-1,2 on page 7,8.)
Lower detection area receives reflected sunlight
or car light, etc.
Remove the reflector or reset the detection area
or mask the area exposed to reflected light.
(See section6-1 - 3 on page 7,8.)
Lower detection area is exposed to direct sunligh
t
or car light. Reset the area so it may not receive direct light. (See section6-1,2 on page 7,8.)
There is any heat source (stove or heater, etc.)
in the area that may cause temperature change. Reset the area or remove the heat source. (See section6-1,2 on page 7,8.)
There is any moving object (laundry on
clothesline, plants, etc.) in the area. Reset the area or remove moving objects. (See section6-1,2 on page 7,8.)
Detection area is not set appropriately. Reset the area appropriately.
(See section6-1,2 on page 7,8.)
Sensitivity is set for L(ow). Reset sensitivity for M(edium) or H(igh).
(See section 6-4 on page 9.)
No detection
occasionally
Make alarms
even though
no moving
object is in
the area
Detector fails
to work.
Alarm is not outputted.
9.TROUBLE SHOOTING
-14-
Faulty wiring to detector.
Lower detection area is exposed to direct sunlight
or car light.
Set switch A-4 for Day/Night and see if it works.
(See section 6-6 on page 9.)
alarm shop

-15-
PROBLEM DESCRIPTION PROBABLE CAUSE REMEDY
Volume controller is set for Low. Reset volume for an appropriate level.
(See section 6-5 on page 9.)
Voice control input is not wired correctly. Wire the voice control input correctly.
(See section 4 on page 5.)
Set DIP switch B-3 (Message A) and
DIP switch B-4 (Message B) for PAUSE. Set DIPswitch B-3 and DIP switch B-4 for ACTIVE.(See section 6-6 on page 9.)
Message A not
displayed. Set DIP switch B-3 for PAUSE. Set DIP switch B-3 for ACTIVE. (See section 6-6 on page 9.)
Message B not
displayed. Set DIP switch B-4 for PAUSE. Set DIP switch B-4 for ACTIVE. (See section 6-6 on page 9.)
No message come out. Too much noise is applied to power supply. Move the detector from the noise source as
much as possible.
Microphone dead. Recording volume controller is not set for Max and recording level indicator does not blink
during recording.
Set the controller for Max and make sure that th
e
indicator blinks during recording.
(See section 5-2 on page 6.)
Connection cable is not suitable for monaural
recording.
Cable is not connected to the earphone or
headphone jack.
Recording level indicator does not blink
during recording.
All recording functions
dead. Both DIP switch B-3 and B-4 are set for ACTIVE or PAUSE.
Set either Track A (DIP switch B-3) or
Track B (DIP switch B-4) for ACTIVE.
Also, make sure that the indicator blinks
during recording.
(See section 5-1 on page 6.)
Message A fails to
record. Not only DIP switch B-3 but also B-4 is set for ACTIVE. Set only DIP switch B-3 (Message A) for ACTIVE.(See section 6-6 on page 9.)
Message B fails to
record. Not only DIP switch B-4 but also B-3 is set for ACTIVE. Set only DIP switch B-4 (Message B) for ACTIVE.(See section 6-6 on page 9.)
External sound sourse
dead.
Use a monaural connection cable to connect the
Detector to the earphone or headphone jack of t
h
sound source. Also, make sure that the indicat
o
blinks during recording.
(See section 5-1,2 on page 6.)
No message at all.
Recording
fails.
No message
output.
alarm shop

This unit is designed to detect movement of an
intruder and activate an alarm control panel.
Being only a part of a complete system, we cannot
accept responsibility for any damages or other
consequences resulting from an intrusion.
This Product conforms to the EMC Directive.89/
336 EEC.
Note: Specifications and design are subject to change without prior notice.
10.SPECIFICATIONS
11.DIMENSIONS
NOTE
-16-
Pitch
83.5mm(3.28")
68.5mm(2.7")
198mm(7.8")
80mm(3.15") 82mm(3.23")
MODEL VX-402 VX-402REC
Detection Method Passive Infrared
Coverage 12m(40ft)90°wide
Detection Zones 14zones
Mounting Height 0.8-1.2m(2.7-4ft)
Sensitivity 2.0°C(3.6°F) at 0.6m/s
Detectable Speed 0.3-1.5m/s(1-5ft/s)
Power Input 9.5-18VDC
Current Draw NC Normal 25mA Max 28mA Normal 25mA Max 180mA
NO Normal 10mA Max 35mA Normal 12mA Max 200mA
Alarm Period 2±1sec
Alarm Output Selectable N.C./N.O.; 28VDC 0.2A Max
Tamper Switch N.C.Opens when cover removed
Pulse Count 20±5sec 2 or 4
Warm-up Period Approx 30sec(LED blinks)
LED blinking during warm-up period
LED Indicator Alarm condition
Recording condition
Weatherproof IP54
Operating Temperature –20 - +50°C(–4 - +122°F)
Environment Humidity 95% Max
RF Interference No Alarm 30V/m
Mounting Wall, Pole, Conduit and Electric box
Weight 550g(19.4oz)
Accessories Pole mount kit, Screw Kit, Area Masking Plate
alarm shop