OSEE RMS5733 User manual

RMS5733
USER MANUAL

Product Information
Model: RMS5733 LCD MONITOR
Version: V040001
Release Date: March 12th, 2015
Company
OSEE TECHNOLOGY CO., LTD.
Contact Information
Address: No.22 Building, No.68 zone, Beiqing Road, Haidian District,
Beijing, China
Post Code: 100094
Tel: [phone]
Fax: [phone]
Web: http://www.osee-dig.com/
E-mail: [email protected]

About The USER MANUAL
The user manual applies to the following device types:
RMS5733-HSC
RMS5733-SC
The images of RMS5733-HSC are adopted in the following descriptions. Any of the
different specifications between the device types are elaborated. Before reading the manual,
please confirm the device type.

Contents
Chapter 1 Product Overview.............................................................................................. 1
Chapter 2 Safety Precaution for Use.................................................................................. 2
Chapter 3 Unpacking and Installation............................................................................... 4
Chapter 4 Using the RMS5733 ........................................................................................... 5
4.1 Status Display of the Screen..........................................................................................................5
4.2 Front Panel Controls......................................................................................................................6
4.3 Quick Button Descriptions............................................................................................................8
4.3.1 ENTER BUTTON............................................................................................................8
4.3.2 USER BUTTON ...............................................................................................................8
4.3.3 MENU BUTTON..............................................................................................................9
4.4 Rear Panel.....................................................................................................................................10
Chapter 5 Main Menu Structure...................................................................................... 12
5.1 STATUS Sub-menu..................................................................................................................12
5.2 VIDEO Sub-menu....................................................................................................................12
5.3 AUDIO Sub-menu....................................................................................................................13
5.4 MARKER Sub-menu...............................................................................................................14
5.5 OSD Sub-menu.........................................................................................................................15
5.6 USER CONTROL Sub-menu..................................................................................................18
5.7 USER CONFIG Sub-menu......................................................................................................19
Chapter 6 Technical Specifications.................................................................................. 20
Chapter 7 Warranty for LCD Monitor............................................................................ 24

User Manual for RM7023 - 1 -
Chapter 1 Product Overview
The RMS5733 is a 3U high rack mountable LCD monitor that offers video and audio monitoring with
high resolution of 640x480. The unit is equipped with full digital processing technology, and its screens
feature anti-glare. The model accepts HD-SDI, SD-SDI and analog composite signal. A high display
quality of all video signals can be ensured by full digital processing. The precise scaling chip as well as
Gamma correction is a guarantee for high quality display image.
The monitor comes with many in monitor display features including WFM, Dynamic UMD, analog
audio input as well as RS485.
Features：
Auto- Sensing for HD/SD-SDI, Composite signal
Embedded Audio Support，4 or 8 Channels Audio Meter (VU & PPM)
H/V Delay, Under Scan, Safe&Area Marker, Aspect Ratio, Blue Only, Tally
1 Pair Audio Monitoring via Headphone Jack. Built-in speaker.
Support COLOR temperature correction.
Support Dynamic UMD, and TSL and IMAGE VIDEO protocols. RS485 connector.
Waveform and Vectorscope display for SDI signal
Support OSD TALLY (SPLIT TALLY); Support LED TALLY.
Support SD ASPECT. When the input is CVBS or SD-SDI, it supports 16:9 and 4:3 display.
Support HD ZOOM. When the input is HD-SDI, it adds the “HD zoom” function to be
changed from 16:9 and 4:3.
An interface is displayed when USER menu is under operation.
Support FPGA and MCU upgrade via RS485.
Product Number Description
RMS5733-HSC Three monitors: each monitor includes one video input and one video output
(support HD-SDI / SD-SDI / CVBS), two external audio input connectors, two
external audio output connectors. One RS485 input (RJ45), One RS485 output
(RJ45).
RMS5733-SC Three monitors: each monitor includes one video input and one video output
(support SD-SDI / CVBS), two external audio input connectors, two external
audio output connectors. One RS485 input (RJ45), One RS485 output (RJ45).

RMS5733 LCD MONITOR User Manual
—2—
Chapter 2 Safety Precaution for Use
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.

User Manual for RM7023 - 3 -
Read and keep these instructions. Heed all warnings. Follow all instructions.
About the Position
1. Do not block any ventilation openings.
2. Do not use this unit near water.
3. Do not expose the unit to rain or moisture.
4. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that product heat.
5. A nameplate indicating operating voltage, etc., is located on the rear panel. Install only in
accordance with the instructions in the section entitled, “Unpacking and Installation” on page 3.
6. The socket-outlet shall be installed near the equipment and shall be easily accessible.
About the Power-supply Cord
7. Do not defeat the safety purpose of the polarized or grounding-type plug.
8. Do not damage the power cord, place the heavy objects on the power cord, stretch the power
cord, or bend the power cord.
9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the unit.
10. If the power cord is damaged, turn off the power immediately. It is dangerous to use the unit
with a damaged power cord. It may cause fire or electric shock.
11. Unplug this apparatus during lighting storms or when unused for long periods of time.
12. Disconnect the power cord from the AC outlet by grasping the plug, not by pulling the cord.
13. Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by
qualified personnel before operating it any further.
Monitor
14. Do not beat with a hard object or scratch the LCD display.
15. Do not make the freeze picture displaying on the screen time too long, otherwise, it will leave
the afterimage on the screen.
16. Install in accordance with the manufacturer’s instructions
17. If the brightness is adjusted to the minimum, then it might be hard to see the display screen.
18. Refer all servicing to qualified service personnel. Servicing will be required under all of the
following conditions:
The unit has been exposed to rain or moisture.
Liquid had been spilled or objects have fallen onto the unit.
The unit has been damaged in any way, such as when the power-supply cord or plug is
damaged.
The unit does not operate normally.
19. Clean only with dry cloth.
20. Specifications are subject to change without notice.

RMS5733 LCD MONITOR User Manual
—4—
Chapter 3 Unpacking and Installation
1. Unpack the RMS5733 Monitor and inspect for any apparent physical damage that
may have occurred in transit. We recommend you retain the shipping carton for future use.
If there be any damage, immediately contact OSEE DIGITAL TECHNOLOGY LTD at
[phone].
2. After inspection, install in your desired location of a standard EIA 19-inch equipment
rack. Adequate ventilation is required when installed to prevent possible damage to the
RMS5733 internal components.
3. Connect required cables for signal input and output. Please note that power must be
applied to the RMS5733 for all outputs to be activated. For BNC connections use 75
rated connectors.
4. Connect A.C. Mains power using the included power cord. Please ensure an Earth
ground present to ensure proper operation of the unit. Fasten the power protect accessory.
5. As a final step turn on each screen of the RMS5733 by depressing the power switch
located on the front of the unit.
Supplied Accessories:
1.Monitor 1
2.12 V DC power supply 1
3.UserManual 1
4.WarrantyCard 1

User Manual for RM7023 - 5 -
Chapter 4 Using the RMS5733
4.1StatusDisplayoftheScreen
1. Tally Light: This tri-color (red/green/amber) light is controlled through a DB9
connector on the rear panel. For more information about the DB9 connector, refer to
“Rear Panel” on Chapter 4.4.
2. Input Signal Format: It displays the input signal format and can be set in the MAIN
Menu.
3. Safe Areas: Multiple safe areas are configurable in the MAIN Menu.
4. Audio Meters: Levels for the audio .For RMS5733-SC, only two meters on the left
side.
5. UMD: The MAIN Menu provides settings to customize the UMD (In-Monitor Display)
text area to show a line of characters, numbers, and/or some symbols.
6. Speakers: Audio may be selected for monitoring through the left and right speakers.
7. Time Code: The de-embedded time code from the HD/SD-SDI source displays in the
top right corner.
8. Waveform and Vectorscope: The signal waveform and vectorscope are configurable
in the MAIN Menu.
Referring to the circumstance of no sync ( power on):
1. Will indicate on the top left hand of screen: IN A: NO SYNC
2. On the bottom of screen will UMD and METER be shown, but the display of
UMD and METER is subject to the current main menu setting. When in the main
Audio Meters
UMD
Input Signal
format
Time Code
Safe Marke
r
Waveform or Vectorscope
Speakers
LED Tally Light
OSD Tally

RMS5733 LCD MONITOR User Manual
—6—
menu UMD DISP is set to ON and, no video input, UMD will display; when it is
set OFF, UMD won’t be displayed. The same applies to the display of METER.
3. The main menu can still be displayed, but the value of parameter relating to image
is not adjustable; and the value of parameter relating to the display effect can be
adjustable.
4.2 Front Panel Controls
1: Power On/Off Switch
When the indicator in the power switch is in green, it indicates that power is on.
When the indicator is flashing, it indicates standby.
2: ASPECT (The screen Aspect Ratio)
The function of “ASPECT” button is the same as “SD ASPECT” parameter in the main menu.
Only for CVBS and SD-SDI input signal, the “SD ASPECT” can be set to display in16:9 or 4:3.
For the model of which the panel is of 4：3 and，when the input is HD-SDI, the “SD ASPECT”
parameter is unavailable. The “HD ZOOM” function (in the USER CONTROL SUB-MENU) will be
available and can be changed from 16:9 (OFF) and 4:3 (ON).
（For more information, please refer to “Chapter 5.6”）
3: USER
“USER” serves as the quick-button; its function can be assigned in the main MENU.
（For more information, please refer to “Chapter 4.3.2”）
4: MENU
Press to display the main menu. （For more information, please refer to “Chapter 4.3.3” and Chapter5）
5/6: Two functions
Press “MENU” button to choose the function you need.
When the “MENU” is not in use, the button of 5/6 can achieve the following functions:

User Manual for RM7023 - 7 -
5. Blue only and mono button:
Blue only: press to eliminate the red and green signals. Only blue signal is displayed as an
apparent monochrome picture on the screen.
Mono: press to display a monochrome picture.
Press the button repeatedly, the button function will circle as follows:
Blue only mono color mode
6. Audio Selection and MUTE button
Audio Selection: press to select the monitoring audio of the corresponding monitor.
Mute: press to mute the sound. “MUTE” will show a continuous flickering lasting for 10S.
To cancel the mute function, press the button again.
Press the button repeatedly, the button function will circle as follows:
Audio Selection Mute
Note: All monitors share one headphone jack. The indicator in lighting shows its audio is being
monitored; in flickering shows its audio is being muted of corresponding monitor.
7: Enter
Enter the menu items when menu is displayed;
Enter instant parameters adjustment when menu isn’t displayed. The following parameters can be
regulated: VOLUME, BRIGHTNESS, CONTRAST, SATURATION, SHARPNESS, HUE.
（For more information, please refer to “Chapter 4.3.1”）
8: HEADPHONE Jack：3.5mm Stereo HEADPHONE Jack

RMS5733 LCD MONITOR User Manual
—8—
4.3 Quick Button Descriptions
4.3.1 ENTER BUTTON
When MENU is not used, you can press ENTER to regulate the following parameters: VOLUME,
BRIGHTNESS, CONTRAST, SATURATION, SHARPNESS, and HUE.
Press ENTER six times, parameters will cycle. You can get the exact value combined with buttons
of ∧（up）or ∨(down).
VOLUME: Used to regulate the volume. Range: -30~0dB, the maximum: 0dB.
BRIGHTNESS: Used to regulate the brightness, range: -116~139, the typical: 0.
CONTRAST: Used to regulate the contrast of image, range: -128~127, the typical: 0.
SATURATION: Used to regulate the saturation of image, range: -128~127, the typical: 0.
SHARPNESS: Used to regulate the sharpness of image, range: 0~15, the typical: 0.
HUE: Used to regulate the hue of image, range: -32~31, the typical: 0.
Note: To regulate the option DEFAULT, use the reset item in video 1/2 of the main MENU. You can reset
the following parameters of BRIGHTNESS, CONTRAST, SATURATION, SHARPNESS, and HUE.
4.3.2 USER BUTTON
Press the USER button on the front panel; it will display the following table. The table will
disappear after 3 seconds without operation.
USER FUNCTION
USER1 H/VDELAY
OFF
USER can be used as quick-button, and include many options. When you choose one option, for
example, if you have already set USER1 at H/V DELAY, you can press “USER1” directly to realize
each function of H/V DELAY, and need not set in the main MENU. Of course you can set “USER1”
at other option accordingly.
The function of USER can be set in the main MENU. Set steps: press MENU, combined with
buttons of ∧（up）or ∨(down), you can find “USER CONFIG” in the sub-MENU, also combined
with buttons of ∧（up）or ∨(down), and you will find USER1~ USER3.

User Manual for RM7023 - 9 -
The different apparatus model includes different user menu items.
The options are as follows. (The underlined value means the DEFAULT value.)
User Menu Items
MODEL
BUTTON ITEM RMS5733-SC RMS5733-HSC
USER 1 H/V DELAY
WFM DISP
SAFE MARKER
AREA MARKER
OSD CONTROL
MON SOURCE
SCAN
H/V DELAY
WFM DISP
SAFE MARKER
AREA MARKER
OSD CONTROL
MON SOURCE
HD ZOOM
SCAN
And each option will be specified as follows.
H/V DELAY：H/V, V, H, OFF. Function: horizontal/vertical blank, vertical blank, horizontal
blank, or no blank.
WFM DISP: It is used to check the waveform / VECTOR of the current signal picture, showing
on the top-right of the screen. Include three options of WFM, VECTOR, OFF.
SAFE MARKER: Display CENTER mark, 90% mark and 80% mark or not.
AREA MARKER: Images show with one scale of 2.35:1, 1.85:1, 15:9, 14:9, 13:9, 4:3 or OFF.
Only when ASPECT is at 16:9, the setting is available.
OSD CONTROL: Display waveform / VECTOR / TC code, UMD code and audio meter or not.
MON SOURCE: Monitor one audio source of four audio sources. Include four options of MET1,
MET2, MET3 and MET4. When MET1 is selected, the first audio source will be monitored.
Likewise, if you select other MET, the corresponding audio source will be monitored.
HD ZOOM: Only for the model of which the panel is of 4：3 and，when the input is HD-SDI, this
function is available. The “HD ZOOM” function can be changed from 16:9 (OFF) and 4:3 (ON).
SCAN: Press to display the 100% image (UNDER SCAN) and 95% (NORMAL) image.
Note: Please set “USER1” to meet your actual requirement. For example, if you often use H/V
DELAY, you’d better set “USER1” at H/V DELAY.
4.3.3 MENU BUTTON
When you want to change the value of a parameter, you may use MENU, and you can follow four
steps.
Step 1:
Press MENU, and you can enter the main MENU.
Step 2:

RMS5733 LCD MONITOR User Manual
—10—
Press buttons of ∧（up）or ∨(down) to choose an option, and the selected sub-MENU icon will
display in yellow. When you get one and press ENTER, and you can enter the sub-MENU.
Step 3:
Press buttons of ∧（ up）or ∨(down) to choose a parameter, and the selected parameter will display
in yellow. Press ENTER, and press ∧or ∨to acquire the exact value. Press ENTER to set some
value.
Step 4:
Press MENU to return. You can follow the same step to set other parameters.
In a word, when you set a parameter, the buttons of ENTER，MENU，∧ and ∨will be used
frequently. The function of each button is listed below.
ENTER: Enter the sub-menu and set the value of a parameter.
MENU: Return to the super-menu with no saving.
∧（up）or ∨(down): Switch the options in the same menu.
Note: in all sub-menu of main menu, pressing “Menu” is to cancel the current set value and
return back to the menu of top level. If setting a value of some parameter, it’s required to
press “Enter” to save current set value.
4.4 Rear Panel
Connectors
HD-SDI/SD-SDI inputs comply with SMPTE259M，SMPTE292M / ITU-R BT601.
Composite Video inputs comply with SMPTE-170M.
Tally lamps are active, when connected to ground.
DC IN
-
12V 2A
+
Pin5:
Pin7:CH2-G
Pin6:CH1-G
Pin8:CH3-G
35
4
GND
Pin2:CH2-R
Pin1:CH1-R
Pin3:CH3-R
12
7896
RS485
VIDEO 1
INSDI OUT
AUDIO 1
R
L
OUT IN
VIDEO 2
INSDI OUT
IN
AUDIO 2
OUT
R
L
VIDEO 3
SDI OUT IN
AUDIO 3
IN
R
L
OUT
Active Output3 Re-Clocked
And Re-Shaped Analog audio loop out 1 TALLY IN DB-9 Male
Monitor Input3
HD-SDI/SDI/ Analog
Composite Input
Analog audio
input 1
12VDC from
Power Supply
IN/ OUT
RS485

User Manual for RM7023 - 11 -
For Tally IN connector (DB9 male) :
Tally IN DB-9 Male
Pin 1 CH1-R Pin 6 CH1-G
Pin 2 CH2-R Pin 7 CH2-G
Pin 3 CH3-R Pin 8 CH3-G
Pin 4 /Pin 9 /
Pin 5 GND
Tally Light Color Screen 1 Screen 2
PIN1 PIN6 PIN2 PIN7
Red GND Open GND Open
Green Open GND Open GND
Amber GND GND GND GND
The description of Screen 3 is similar with Screen 1.
For IN/ OUT RS485 connector (Female RJ-45):
Support for dynamic UMD and updating the new firmware.
( Female RJ-45 Receptacles )
Pin No. RS485 IN Terminal Signal RS485 OUT Terminal Signal
1,2 GND GND
3 Tx- Tx-
4 Rx+ Rx+
5 Rx- Rx-
6 Tx+ Tx+
7,8 NC NC
For Analog audio loop out connector:
The audio loop out interface refers to the loop out for analog audio only and is not applicable to
embedded audio. The monitoring for embedded audio can be done only through headphone jack.

RMS5733 LCD MONITOR User Manual
—12—
Chapter 5 Main Menu Structure
The descriptions of main menu structure are as follows:
(The operation of main menu refers to Chapter 4.3.3)
The main menu includes seven sub-menu icons. The sub-menus are:
A. STATUS
B. VIDEO
C. AUDIO
D. MARKER
E. OSD
F. USER CONTROL
G. USER CONFIG
Note: For the following menu description, “O” stands for the unit including this function; whereas “X”
indicates the unit includes no such function. The underlined values are factory preset setting values.
(The presets are values adjusted before shipment from factories.) The available parameters and
values show in white; the unavailable parameters and values show in blue.
5.1 STATUS Sub-menu
The STATUS Sub-menu is used to display the current status of the unit. The following items are
displayed:
Parameters Input Signal
CVBS SD-SDI HD-SDI Display Value
FORMAT O O O IN A
1080I60
COLOR TEMP O O O D65
MON SOURCE O O O MET 1
SCAN O O O NORMAL
SD ASPECT O O O 4:3
MODEL O O O RMS5733-HSC
This Sub-menu can’t be entered, only display Information. The model will display corresponding unit
type depending on the actual unit.
5.2 VIDEO Sub-menu
Parameters Input Signal Domain Range NOTE
CVBS SD-SDI HD-SDI
VIDEO (1/2)
BRIGHTNESS O O O -116…000…139 Adjust the picture brightness
CONTRAST O O O -128…000…127 Adjust the picture contrast
SATURATION O O O -128…000…127 Adjust the picture saturation
SHARPNESS O O O 000…15 Adjust the picture sharpness
HUE O O O -32…000…31 Adjust the picture hue
RESET O O O Reset BRIGHTNESS, CONTRAST,
SATURATION, SHARPNESS, HUE to
default value. Once “Reset” is set, all
parameters above will respond to change.

User Manual for RM7023 - 13 -
COLOR TEMP O O O USR…D56…
D65…D93
Used to select the color temperature that
will become the basis for adjustments.
<USR> Color temperature of user set.
<D56> Color temperature around 5600K
<D65> Color temperature around 6500K
<D93>Color temperature around 9300K
VIDEO (2/2)
R GAIN O O O 0…128…255 Gain elements for RED are adjusted.
G GAIN O O O 0…128…255 Gain elements for GREEN are adjusted.
B GAIN O O O 0…128…255 Gain elements for BLUE are adjusted.
R OFFSET O O O 0…128…255 Offset elements for RED are adjusted.
G OFFSET O O O 0…128…255 Offset elements for GREEN are adjusted.
B OFFSET O O O 0…128…255
Offset elements for BLUE are adjusted.
RESET O O O “R GAIN”- “B OFFSET” values are reset
to color temperatures values selected in
“COLOR TEMP”.
NOTE: When adjusting, the item displays of “BRIGHTNESS”-“HUE” and “R GAIN”-“B OFFSET” move to
the lower part of the screen.
5.3 AUDIO Sub-menu
PARAMETERS Input Signal Domain Range NOTE
CVBS SD-SDI HD-SDI
AUDIO (1/3)
AUDIO MON O O O ON…OFF Used for headphone.
The default of left panel is set to ON, others
is set to OFF. “AUDIO MON” can be only
set from “OFF” to “ON”，a reverse cannot be
allowed.
MON SOURCE O O O MET 1…MET 4 Used to set the monitoring audio source
from among audio meters.
Note: For RMS5733-HSC, there are four
audio meters (MET1~MET4).
For RMS5733-SC, there are only two
audio meters (MET1~MET2).
VOLUME O O O 00dB…-30dB…MUTE Used to adjust the volume value.
“MUTE” changes to a continuous flickering
lasting for 10S.
METER SIZE O O O SMALL…LARGE Used to set the size of the audio meter
display.
When the SD ASPECT is 16:9, the
meter size will only display in type of
SMALL, both in the METER SIZE
selection of SMALL and LARGE.
When the SD ASPECT is 4:3, the meter
size will display the size type,
responding to the METER SIZE
selection of SMALL and LARGE

RMS5733 LCD MONITOR User Manual
—14—
METER H POS L O O O 000…255 Used to set the horizontal position of left
audio meter.
METER H POS R O O O 000…255 Used to set the horizontal position of right
audio meter. Only used for RMS5733-HSC.
TEST LEV O O O -18dB…-20dB Used to set the test level of audio meter.
AUDIO (2/3)
IN A: MET 1 O O O NONE…VU
…PK…VU+PK
Used to set the audio meter types.
Note: For RMS5733-HSC, there are four
audio meters. For RMS5733-SC, there are
only two audio meters.
IN A: MET 2 O O O NONE…VU
…PK…VU+PK
IN A: MET 3 O O O NONE…VU
…PK…VU+PK
IN A: MET 4 O O O NONE…VU
…PK…VU+PK
IN A: MET 1-L O O O EBD1 Used to assign the audio channel for left
audio meter 1 display from among
“EBD1…EBD16” and “EXT1L…EXT1R”.
IN A: MET 1-R O O O EBD2 Used to assign the audio channel for right
audio meter 1 display from among
“EBD1…EBD16” and “EXT1L…EXT1R”.
IN A: MET 2-L O O O EBD3 The similar as meter 1.
AUDIO (3/3)
IN A: MET 2-R O O O EBD4 The similar as meter 1.
IN A: MET 3-L O O O EBD5 The similar as meter 1. Not valid for
RMS5733-SC.
IN A: MET 3-R O O O EBD6
IN A: MET 4-L O O O EBD7
IN A: MET 4-R O O O EBD8
5.4 MARKER Sub-menu
PARAMETERS Input Signal Domain Range NOTE
CVBS SD-SDI HD-SDI
SAFE MARKER1O O O ON…OFF Select ON to enable the safe
area mark of the picture display
and OFF not to display.
CENTER O O O ON…OFF Select ON to display the center
mark of the picture and OFF not
to display.
No function in h/v delay mode
90% O O O ON…OFF Select ON to enable the 90%
safe area size of the image
display and OFF not to display.
No function in h/v delay mode
80% O O O ON…OFF Select ON to enable the 80%
safe area size of the image
display and OFF not to display.
No function in h/v delay mode

User Manual for RM7023 - 15 -
AREA MARKER2X O O OFF…2.35:1
…1.85:1…15:9
…14:9…13:9
…4:3
Used to set type of the area
marker.
No function in h/v delay mode
and in 4:3 aspect ratio for SD
SDI input
Note: 1. SAFE MARKER
When SAFE MARKER is set to ON, the value of “CENTER”，“90%”，“80%”changes
between ON, OFF. Each function is available.
When SAFE MARKER is set to OFF, the functions of “CENTER”，“90%”，“80%” are not
available.
2. Refer to the “AREA MARKER” parameter:
Only when the image displaying in 16：9 format, this function is available.
5.5 OSD Sub-menu
PARAMETERS Input Signal Domain Range NOTE
CVBS SD-SDI HD-SDI
OSD (1/3)
STD DISP O O O ON…AUTO OFF…OFF Displays the input signal
format on the top left of the
screen.
• ON = Always displayed
• AUTO OFF= Displayed for
about 10 seconds after change
• OFF = Hidden
WFM/VT DISP X O O VECTOR…WFM…
OFF
•VECTOR: Displays
vectorscope.
•WFM: Displays waveform
• OFF: not to display
TC DISP X O O ON…OFF • ON: Displays the time code
• OFF: not to display
UMD DISP O O O ON…OFF • ON: Displays UMD
•OFF: not to display
OSD TLY DISP *1O O O ON…OFF
OSD TLY MODE *1O O O RGY…GR…GR
LED TLY DISP *2 O O O ON…OFF
OSD (2/3)
UMD FIXED SETUP*3 O O O
@ABCDEFGHIJKLMNO
16 CHARS
COLOR *4 O O O RED…GREEN
…YELLOW…WHITE
ALIGN *5 O O O LEFT…CENTER…
RIGHT
UMD PROTOCOL*6 O O O LOCAL…TSL V3.1
…TSL V4.0…IMAGE
VIDEO

RMS5733 LCD MONITOR User Manual
—16—
UMD ID *7 O O O 0…255 The device can be set
independently through the
downloading software and
with the set value, convenient
for remote control
OSD (3/3)
UMD NAME(S/N)*8 O O O S00000 16 Characters totally. UMD
NAME is in compliance with
IMAGE VIDEO Protocol
UMD TLY MODE *9 O O O T1…T2…T1T2…T2T1
…T1-…T2-…T1T2-
…T2T1-…
UMD TLY MODE is in
compliance with IMAGE
VIDEO Protocol
UMD BAUD RATE *10 O O O 2400…4800…9600…
19200…38400…57600…
115200
TLY SOURCE *11 O O O STANDARD…IMAGE
VIDEO HW…IMAGE
VIDEO 422…
STANDARD+IV422…
TSL
NOTES:
*1. OSD TLY DISP, OSD TLY MODE
Use these settings to choose how tally is displayed on the screen. The available OSD Tally
options depend on the Tally Source. OSD TLY DISP can be set to Off，ON；OSD TLY MODE
can be set to RGY, RG, or GR:
When the Tally Source is set to STANDARD or STANDARD+IV422, OSD TLY MODE is
available. When the Tally Source is set to IMAGE VIDEO 422、TSL and IMAGE VIDEO HW,
OSD TLY MODE is unavailable.
• Off: On-screen tally is disabled.
• ON: On-screen tally is enabled.
• RGY: Red, yellow, or green tally signals are indicated at both the bottom left and bottom right
corners of the screen near UMD.
• RG: Red tally is shown at the bottom left of the screen and green is shown at the bottom right.
• GR: Green tally is shown at the bottom left of the screen and red is shown at the bottom right.
*2. LED TLY DISP
Use this setting to enable or disable the LED Tally. When it is set to ON, the yellow, red and
green LED above each display will respond to tally commands, according to the Tally Source
setting.
*3. UMD FIXED SETUP
Use this setting to display static UMD text on the screen. This setting is used to enter UMD text
locally, when a serial protocol is not used for remote control. The UMD will be overridden by serial
protocol commands.
Press ENTER to edit the UMD. Use the ENTER button to move the cursor. Press ENTER with the