Outdoor GreatRoom Company Brooks BRK-1224-19 User manual

1
Brooks and Kenwood Fire Pit Table
Installation Instructions for the following Fire Pit Tables:
BRK-1224-19, BRK-1242-19, BRK-2424-19, BRK-1242-19-W,
KW-1224-19, KW-1242-19, KW-2424-19

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this
installation
Contents
Required Tools…………………………………................2
Included with your Fire Pit……………………….……..3
Assembly Instructions…………………………….…..….4
CF-SPARKER Installation …………………………..…...6
Gas Connections…………………………………………….7
Thermocouple Installation……………………………..8
Electrode Installation………………………………….....8
Fire Media Installation……………………………………9
Position Your Tank……………………………………….10
Riser Kit Installation…………………………………..…11
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42490 REV I 11-18-21

3
Included with your Fire Pit
Panel C [X1]
M6 Allen
Wrench [X1]
TOUCH
UP
PAINT
M6X20
Panel B [X1]
Access Door [X1]
Top [X1]
Center Support [X1]
Bolt A [X12]
CFP Burner
Panel A [X1]
Touch-Up
Paint Bottle
[X1]
Optional Riser Kit:
Required to fit 20# propane tank
under table

4
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
1. Unpack contents from box, and remove individual packaging from each
piece.
2. Lay Side Panel with Control Panel on soft, flat surface.
3. Position Support Piece on the Side Panel. NOTE: It is very important to
positon the Support Piece as shown in the picture below, to ensure that
your burner and propane tank fit correctly with your fire pit table base.
Assembly Instructions
INSTALL NOTE: Final tightening of bolts should be completed following
installation of all panels.
1. Unpack all the contents from the box and remove the individual
packaging from each component.
2. Carefully lay the Top, with underside facing upwards, on a soft and flat
surface.
3. Attach Panel A using Bolt A (X2) as shown below.
4. Attach Panel B on the opposite side of Panel A using Bolt A (X2)
as shown below.

5
5. Attach Panel C using Bolt A (X4) as shown below.
6. Attach Center Support piece, as
shown below, to the bottom of
the fire pit using Bolt A (X4).
NOTE: Drainage holes on
Center Support piece must be
facing down towards the
surface on which you will be
placing your fire pit.
NOTE: Drainage holes on
Panel C must be facing
down towards the surface
on which you will be
placing your fire pit.
Drainage holes

6
8. Do a final tightening of the bolts you have installed in your fire pit.
Then, with the help of another person, turn the table right side up.
Top
CF-SPARKER Installation
Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

7
Gas Connections
Read and understand your Crystal Fire® Plus owner’s manual
before beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
See Crystal Fire® Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.
Insert screws
included with
Gas Valve Kit

8
OFF
Thermocouple Installation
•Refer to Crystal Fire® Plus instruction manual for detailed attachment
of thermocouple.
•Attach thermocouple to burner valve as shown below.
Electrode Installation
Connect igniter and ground wire to sparker box. Both wires can
connect to either connection point. The unit will operate in either
configuration.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire® Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

9
Fire Media Installation
Scatter all included glass beads, lava rock, or other approved fire
media evenly across entire burner surface.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED
GLASS BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE® BURNER WITH BURNER COVER IN PLACE

10
After installing CF-SPARKER and making gas connections,
verify that all connections are tight and that no leaks are
present using a solution of soapy water or a commercially
available leak-check solution.
Position Your Tank
(if applicable)
1. Connect the propane hose/regulator to the propane tank and
hand tighten (DO NOT USE A WRENCH) and slide the propane
tank past the dotted line to ensure the Access Door closes
properly. Attach the Access Door.
2. With the tank inside, ensure that no hoses, wires, or any other
components are kinked or touching the burner pan.

11
Riser Kit Installation
1. Assemble base according to
Manual included with table
2. Screw (4) spacers into threads
on the underside of the table
surface
3. Place base, upside-down, onto
spacers
4. Secure base to spacers using 4
screws (included with table
packaging). Do not overtighten.
4X
4X
HAND-TIGHTEN ONLY. DO NOT USE TOOLS TO
TIGHTEN THE RISER KIT HARDWARE.

12
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Care and maintenance note:
Light scratches may be removed from the poly-wood surfaces of this
fire pit by gently sanding with 220-grit sandpaper in the same
direction as the grain. Sanding too deeply or not following the grain
of the material could result in permanent damage.
9583 217th St. W. •Lakeville, MN 55044
Toll Free: 1-866-303-4028 •[e-mail]
Warranty: Fire pit tables are covered under a 1- year
manufacturer’s warranty. Please visit
https://www.outdoorrooms.com/product-registration
to register your product.