Outdoor GreatRoom Company CR-1242 User manual

1
Cedar Ridge Fire Pit Table
Installation Instructions for Cedar Ridge Fire Pit Table
CR-1242

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this
installation
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
Gas Connections……………………………………….7
Igniter Installation…………………………………….9
Glass Installation………………………………………10
Position Your Tank…………………………………..11
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CF-1242 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
424579 REV B 8.8.16

3
Included with your Fire Pit
Panel C [X 1]
M6 Allen
Wrench [X 1]
Bolt Caps
[X 4]
TOUCH
UP
PAINT
Touch-up
Paint [X 1]
M6X35
M6X20
Center Support
[X 1]
Bottom
Top
Panel A [X 1]
Panel B [X 1]
Access Door [X 1]
Supercast Top
Crystal Fire CF-1242 Burner
Kit
Bolt A [X 4]
Bolt B [X 4]
Gas Valve Kit
Gas Valve (x1)
Mounting
screws (x2)
Control knob
(x1)
Supercast Burner Cover

4
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
Assembly Instructions
1. Unpack the fire pit table contents from the box, and remove individual
packaging from each piece.
2. Lay Panel A on soft, flat surface.
3. Position Center Support on Panel A.
NOTE: it is very important to place the Center Support exactly as shown in
the picture below. This will ensure that your burner (and propane tank, if
applicable) will fit correctly with your fire pit table base. (Refer to “Included
with Your Fire Pit” for component details).
NOTE: curve facing
inward toward
Control Panel.
4. Attach Center Support with Bolt A (x2).
A
A
Panel A

5
4. Stand up Panel A and use 2 more Bolt
Ato attach Center Support to Panel B.
5. Use Bolt B (x4) to attach
Panel C as shown.
A
A
B
Panel C
6. Attach Access Door.

6
7. Hold the Gas Valve in place from behind the control panel while
inserting the two included screws. Use a Philips screwdriver to fasten.
Attach control knob by pressing on to the valve stem.
8. Set Supercast Top directly onto base as shown below.
Press on to stem
Insert screws
included with
Gas Valve Kit

7
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information)
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Gas Connections
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane
input
Natural
gas input
or
Natural gas supply line
as specified by local
building codes

8
3. Set Burner into the fire pit base exactly as shown and make final gas
connection to the Control Panel.
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Igniter
Igniter
Access
Door

9
Igniter Installation
Sparker will not operate correctly without an ignition and ground wire
attached.
Plug both BLACK wires hanging from the burner into the back of
the sparker box.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Owner’s Manual, if
the spark is weak, intermittent, or not present.
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using a
AAA battery (not included).
Negative end should be placed
inside the CF-SPARKER, positive
end outside of the CF-SPARKER.
OFF

10
Glass Installation
1. Scatter all of the included Glass Beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT
GLASS BEADS OR OTHER DECORATIVE MEDIA
PRESENT
DO NOT OPERATE CRYSTAL FIRE BURNER WITH SUPERCAST
BURNER COVER IN PLACE