Outdoor GreatRoom Company Providence Fire Pit User manual

1 | P a g e
Providence Fire Pit
Installation Instructions For All Providence Fire Pit
Models And top Styles

2 | P a g e
Contents
Package Contents and Required Tools………3
Placing and assembling the Table.…4-7
Gas
Connection……………………….…………….8
Igniter
Installation…………….………………………...9
Locating Propane tank………..………….11
Finishing Touches…………………………..12
90209 REV A 4-4-14

3 | P a g e
Required Tools
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found
on the coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter
installation.
Electric Screw Gun with Philips tip
(used for metal tops excluding brushed
stainless model)
Included in packaging

4 | P a g e
Placing and Assembling the Fire Pit table
(STAINLESS STEEL TOP)
1. Remove all components from packaging.
2. Move the base (remove door) to desired
location and set into place.
3. When locating your coffee table, refer to the
manual included with your burner and maintain
clearance to combustibles.
4. Set burner into place with the igniter at the
opposite end from the door of the fire pit. See the
section labeled Gas Connection and Igniter
Installation to install gas lines and piezoelectric
igniter , then set the stainless steel top into place
on TOP of the burner.
Igniter

5 | P a g e
Placing and Assembling the Fire Pit table
(Silver and Copper Vein Powdercoated Tops)
1. Remove all components from packaging.
2. Move the base (remove door) to desired location
and set into place.
3. When locating your coffee table, refer to the
manual included with your burner and maintain
clearance to combustibles.
4. This model utilizes a metal bracket to keep the
top from sliding around during windy conditions or
when bumped. Place the bracket on the door-side
of the fire pit as shown and line holes up. Insert
two screws as shown.

6 | P a g e
5. Set burner into place with the igniter at the
opposite end from the door of the fire pit. See the
section labeled Gas Connection and Igniter
Installation to install gas lines and piezoelectric
igniter , then set the metal top into place on TOP of
the burner.
6. The underside of this top has two screw holes.
Rotate the top to match these up with the
previously installed tab, set the top onto the base,
and slide the mounting bracket up and under the
lip of the powdercoated top. Line up screw holes
and insert two screws at shown.
NOTE: Do not
attempt to lift or
carry fire pit by its
top. Always lift
from the base!

7 | P a g e
Placing and Assembling the Fire Pit
table (Marbelized SuperCast top)
1. Remove all components from packaging.
2. Move the base (remove door) to desired location
and set into place.
3. When locating your table, refer to the manual
included with your burner and maintain clearance
to combustibles.
4. With the help of another person, carefully set
the SuperCast top into place on the base and
center it.
5. Set burner into place. See the section labeled
Gas Connection and Igniter Installation to install
gas lines and piezoelectric igniter

8 | P a g e
Gas Connection
1. Remove stainless steel top (if applicable) and lift
burner out of base to expose control valve.
2. Connect the incoming gas hose to the valve and
using two wrenches tighten securely. Repeat
with flexible metal gas line from the valve to the
underside of burner. It is not recommended to
use Teflon tape or pipe dope on the connection
to the valve with flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and any
other info not listed here consult your Crystal
Fire owner’s manual.
Attach incoming
gas here
Read and understand your Crystal Fire owner’s manual
before beginning burner hookups or using the device.
NOTE: Check for proper orifice size for the type of gas you are
using. NATURAL GAS: #31 , LIQUID PROPANE: #43
(orifices are screwed into the end of the burner “neck” and
have their size stamped on the outside)

9 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut.
Install as shown below.

10 | P a g e
3. To properly install ignition system, a spark and ground wire
need to be attached to the igniter box.
Make sure both black wires attached to the burner are
securely plugged into the backside of the sparker box
as shown.
Ensure that an AAA battery is installed in the sparker
box with the positive (+) side facing outward. Test
system by depressing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section of burner owner’s manual if spark is weak,
intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position and replace stainless steel top if
applicable.

11 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below. This is to allow
the door to close completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line
Install door by setting the bottom on the catching hooks first and
then closing. Magnets in the table will hold door closed.

12 | P a g e
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1224 BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

13 | P a g e
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.

14 | P a g e

15 | P a g e

16 | P a g e
© 2014 The Outdoor GreatRoom Company
2015 Silver Bell Road •Suite 195 •Eagan, MN 55122
Toll Free: 1-866-303-4028 •[e-mail]